Specifications

3 - 2 3 - 2
3. SPECIFICATIONS
3.2 Performance Specifications
The following describes the performance specifications of the RFID interface module.
Table 3.1 Performance Specifications
Item Specifications
RFID
side
Connectable antenna
V680-HA63A+V680-HS□□
V680-HA63B+V680-HS□□
V680-H01-V2
Number of connectable
antennas
1 antenna
CC-Link
side
CC-Link station type Remote device station
CC-Link version Ver. 1.10 and Ver. 2.0
Station number selections
With 2 occupied stations: Station numbers 1 to 63
With 4 occupied stations: Station numbers 1 to 61
Transmission speed
156kbps/625kbps/2.5Mbps/5Mbps/10Mbps (selectable)
Number of occupied stations
and data transfer volume
CC-Link
version
Number of
occupied
stations
Expanded
cyclic setting
Data transfer
volume
*1
Amount of data
readable/writable with
one ID command
Ver.1.10
2 occupied
stations
8 words 10 bytes
4 occupied
stations
16 words 26 bytes
Ver.2.0
2 occupied
stations
Double 16 words 26 bytes
Quadruple 32 words 58 bytes
Octuple 64 words 122 bytes
Connection cable
Ver. 1.10 compatible CC-Link dedicated cable
CC-Link dedicated cable (Ver. 1.00 compatible)
CC-Link dedicated high performance cable (Ver. 1.00 compatible)
External power supply
24V DC (20.4 to 26.4V DC) (ripple rate: within 5%)
Current consumption: 0.33A
Noise resistance
DC-type noise voltage 500Vp-p, noise width 1μs, based on a noise simulator with
a noise frequency of 25 to 60Hz
Withstand voltage All DC external terminals – Ground: 500V AC, 1 minute
Insulation resistance
All DC external terminals – Ground: 500V DC,
10MΩ using insulation resistance tester
Outer dimensions 65(H)X150(W)X45(D)[mm]
Weight 0.3kg
External
connection
method
Communication area,
module power supply area
7-point 2-piece terminal block [transmission circuit, module power supply, FG]
M3 x 5.2 screws (tightening torque range: 4.70 to 5.22in•lbs (0.54 to 0.59N•m)
Number of inserted compatible crimp terminals: 2 or less
Module installation screws
M4 screw with plain washer finished round
(tightening torque range: 0.79 to 1.08N•m)
DIN rail installable, installable in 6 directions
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (JIS C 2812 compliant)
Applicable crimp terminals
• N1.25-3 (JST Mfg. Co., Ltd.)
[compatible wire size : 0.3 to 1.25mm
2
(AWG20 to 16)]
• N2-MS3 (JST Mfg. Co., Ltd.)
[compatible wire size : 1.25 to 2.0mm
2
(AWG16 to 14)]
Applicable Compression tools for wire
connectors
• YNT-2216 (JST Mfg. Co., Ltd.),
T-212 (Nippon Tanshi Co., Ltd.),
NH11 (Nichifu Co., Ltd.)
[compatible wire size : 0.3 to 1.25mm
2
(AWG20 to 16)]
• YNT-1614 (JST Mfg. Co., Ltd.),
T-221N (Nippon Tanshi Co., Ltd.),
NH12 (Nichifu Co., Ltd.)
[compatible wire size : 1.25 to 2.0mm
2
(AWG16 to 14)]
*1. The value includes the command code specification area, etc., as well.
3