MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL FFT9905SKHFW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor.
CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards.
RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
In and after the middle of this page, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development Unit S-114 94 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address: http//www.tco-info.
Diamond Scan 90e User’s Guide CONTENTS 1. INTRODUCTION .................................................................................................. 1.1 Features ..................................................................................................... 1.2 Internal Preset Memory Capability ............................................................. 1.3 Power Management Function .................................................................... 1.4 DDC ...................................
1 INTRODUCTION Congratulations on your purchase of the Diamond Scan 90e high resolution color monitor. Mitsubishi designed this monitor to provide you with years of reliable trouble-free operation. Once again, thank you for selecting our product and welcome to Mitsubishi! This guide tells you how to connect, adjust and care for your Diamond Scan 90e monitor. This guide also provides technical specifications and instructions for troubleshooting any basic problems you may experience with your monitor. 1.
1.2 Internal Preset Memory Capability To minimize adjustment needs, the factory has preset popular display standards into the monitor, as shown in Table 1. If any of these display standards are detected, the picture size and centering are automatically adjusted. All of the factory presets may be overwritten by adjusting the user controls. The monitor is capable of automatically storing up to 6 additional display standards.
1.4 DDC The monitor includes the DDC1 and DDC2B feature. DDC (Display Data Channel) is a communication channel over which the monitor automatically informs the host system about its capabilities (e.g. each supported resolution with its corresponding timing). DDC is routed through previously unused pins of the 15-pin VGA connector. The system will perform "Plug and Play" feature if both, monitor and host, implement the DDC protocol. 1.
1.7 Unpacking After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you ship or transport the monitor. Complete and mail in warranty cards. 1 4 3 2 N 1 5 20 -A AD O 2 3 M 4 IT 5 SU BI 6 SH I 1. Diamond Scan 90e Color Monitor 2. AC Power Cord 3. Signal Cable SC-B102 4. Macintosh Adapter AD-A205 5. User’s Guide 6.
1.9 Quick Operation Chart To summarize the steps in connecting your computer and adapter with Diamond Scan 90e color monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the Diamond Scan 90e color monitor and the signal cable between the Diamond Scan 90e and the graphics adapter. See 2.1 AC Power Connection 2.2 Signal Cable Connection Turn on the computer. Turn on the Diamond Scan 90e color monitor. See 3. USER CONTROLS 4.
2 CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P connector, BNC connector for video and a DIN-8P connector for the optional USB-unit. 2.1 AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet.
2.2.2 Connecting to An Apple Macintosh Centris, Quadra, and Apple Macintosh II Family Figure 4 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple Macintosh. 1. 2. 3. 4. 5. 6. 7. Power off, both the monitor and the computer. Set the DIP switches of Macintosh Adapter according to the setting chart. (See 7.
BNC CONNECTION (1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN): Connect the R, G and B video signals to the BNC receptacles on the back of the monitor. D-SUB R G B COMP. HD VD Serial (2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively. D-SUB R G B COMP.
3 USER CONTROLS 3.1 Control Names See Figure 6 and 7 for the location of the following user controls and indicators. Each control is identified by number and is described individually on page 14. [How to use the front control panel] ” on Press the button marked “ the control panel to open.To close, press it again. FRONT 1. POWER SWITCH 2. POWER-ON INDICATOR 4. OSD OFF BUTTON BNC/D-SUB 6. FUNCTION ADJUST BUTTONS OFF ADJUST DEGAUSS SELECT 3. INPUT CONNECTOR SELECT BUTTON 7. DEGAUSS BUTTON 5.
REAR D-SUB R G B Serial COMP. HD VD SIGNAL INPUT CONNECTOR (DB9-15P) AC POWER CONNECTOR 9. DC POWER OUTPUT CONNECTOR D-SUB R G B COMP. HD VD Serial 8. SERIAL INTERFACE CONNECTOR (DIN-8P) SIGNAL INPUT CONNECTOR (BNC) Figure 7 8. SERIAL INTERFACE CONNECTOR: The monitor has a DIN-8P connector for serial interface communication. This connector will be used for optional USB unit. For the information about connecting, please refer to the instruction which is included in each optional kit.
4 OSD(On Screen Display) FUNCTIONS (1) (2) (3) (4) CONTRAST: Adjusts to the desired contrast level. BRIGHTNESS: Adjusts to the black level of the screen. COLOR-TEMPERATURE: Adjusts the color temperature of the screen image. INFORMATION: Indicate current Scanning frequency and input Video signal port (signal connector) (5) H-SIZE (Horizontal Size): Controls the horizontal size of the image on the screen. (6) H-PHASE (Horizontal Position): Controls the horizontal position of the image on the screen.
4.1 Operation Press any select button and control indicators will be superimposed on the display screen called 1st layer. Refer to Figure 6 for the location of the monitor function ( ) controls. Press the select buttons to choose one of the following controls. The indication of a function symbol changes to blue. When selected the function symbol of above OSD, press the adjust button ( or ), the OSD screen changes to following called 2nd layer. Then you can adjust each function by buttons.
2 10 6 14 15 3 7 11 1 4 5 8 9 12 16 13 z 17 USB z z CLAMP VIDEO 20 CONT R AS T 18 Symbol of 1st OSD layer 19 Press the Minus Adjust Button: Press the Plus Adjust Button: 2nd OSD layer 1 CONTRAST CON T R A S T 9 0% LEVEL: 00 - 100% To increase the contrast. To decrease the contrast. Press plus and minus buttons together, to restore to factory preset level. 2 BRIGHTNESS BR I GH T N E S S 9 0% To decrease the brightness. To increase the brightness.
Symbol of 1st OSD layer Press the Minus Adjust Button: Press the Plus Adjust Button: To narrow the width of the image on the screen. To expand the width of the image on the screen. To move the image to the left. To move the image to the right. 2nd OSD layer 5 H-SIZE H-S IZE 9 0% LEVEL: 00 - 100% 6 H-PHASE H - PHASE 9 0% LEVEL: 00 - 100% 7 V-SIZE V- S I ZE 9 0% LEVEL: 00 - 100% To narrow the height of the image on the screen. To expand the height of the image on the screen.
Symbol of 1st OSD layer 10 Press the Minus Adjust Button: Press the Plus Adjust Button: The decrease the width at the top of the screen image and to increase the width at the bottom. The increase the width at the top of the screen image and to decrease the width at the bottom. 2nd OSD layer KEYSTONE KE Y S T ONE 9 0% LEVEL: 00 - 100% 11 PIN-BALANCE P I N - B AL A NCE 9 0% LEVEL: 00 - 100% 12 To move the top and bottom of the screen image to the right.
Press the Minus Adjust Button: Symbol of 1st OSD layer 15 Press the Plus Adjust Button: 2nd OSD layer ROTATION RO T A T I ON 9 0% To rotate to the left. LEVEL: 00 - 100% 16 To rorate to the right. Press plus and minus buttons together, to restore to factory preset level. GEOMETRY RESET To cancel the geometry reset operation. GEOME T R Y - R E S E T C A NC E L PROCEED To reset the geometry data to factory adjusted condition. MEMORY 17 POWER-SAVE To select the constant power-on mode.
Press the Minus Adjust Button: Symbol of 1st OSD layer 20 USB PORT SELECT USB 21 Press the Plus Adjust Button: 2nd OSD layer USB S T A T US P L E A S E C H E CK MO N I T OR CO N NE C T I ON OR USB IS S US P E NDED This "USB PORT SELECT" is prepared for optional part "USB-unit KT-X406" installed only. Attention OSD screen is displayed without USB unit. For installing USB-unit, please read the manual of USB kit. ADJUST LOCK 1.
4.2 POWER SAVE NOTE When the monitor has no sync signal or incorrect connection and the signal frequency is out of range, the following CAUTION comes on the screen. Check input signal, signal cable connection and signal frequency. 1. POWER SAVE IS OFF When POWER SAVE is OFF and there is no sync signal, the following screen is displayed. AT T E N T I ON NO S I GNAL P L E A S E C H E CK I N P U T S I GNAL OR CO N NE C T I ON . 2.
5 TROUBLESHOOTING Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in SPECIFICATION 6 and APPENDIX 7. ITEMS TO CHECK PROBLEM No picture • Front (Adjust to the maximum brightness or push the reset button) • Front Power switch. • Rear AC power cord disconnected. • Rear Signal cable disconnected.
6 SPECIFICATIONS Size Mask type Gun Deflection angle Phosphors 49.5cm/19" (46cm/18" Diagonal Viewable Image) Shadow Mask In-line 100° CRT Red, Green, Blue EBU (medium short persistence) Crystal pigment Dot pitch 0.25mm Face Plate Anti-glare, Anti-reflection and Anti-static coating Focusing method Double Quadrupole-Dynamic Astigmatism and Focus system (DQ-DAF) INPUT SIGNAL Video 0.7 and 1.0Vp-p analog RGB Sync Sync. on Green or separated H, V sync.
7 7.1 APPENDIX Monitor Signal Input Connector (DB9-15P) Pin No. 1 2 (Female) 5 DB9-15P 4 14 15 2 3 9 10 12 13 1 7 8 6 11 MOUNTED ON THE REAR PANEL DDC ............. SDA .............. SCL .............. NC ................ 7.
7.3 SC-B102 Signal Cable PIN ASSIGNMENT AND SIGNAL LEVEL Approx. 1.8m 2 1 6 11 DB9-15P (Male) DB9-15P (Male) Wire : 5 coaxial SIGNAL ANALOG PIN ASSIGNMENT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RED GREEN BLUE GROUND DDC GROUND RED GROUND GREEN GROUND BLUE GROUND NC SYNC GROUND GROUND SDA HORIZONTAL SYNC VERTICAL SYNC(VCLK) SCL SIGNAL LEVEL NC .....................
7.4 Macintosh Adapter AD-A205 settings The AD-A205 Macintosh Adapter allows you to take advantage of the built-in video capabilities of your Macintosh computer with the monitor. With it, you may select any available video mode via the DIP Switches. Using the following chart, find the computer/resolution combination you wish to configure. There are alternate settings available for most computer / resolution combinations, but we recommend you set the factory preset timing. (see 1.
AD-A205 Mac Adapter settings Chart Apple Apple Power Macintosh Macintosh Macintosh Macintosh Macintosh Macintosh Macintosh Macintosh Macintosh LC 630, LC III, IIvi,llvx Quadra Quadra Quadra display display Macintosh LC,LC II IIci COMPUTER LC 475 -orPerforma 700,900 605,610, 840AV, Card Card Workgroup -orIIsi -orPerforma 630 650,800, 660AV 4•8,8•24, 24AC Server Performa -or600, 950 -or8•24GC 9150 400,405, Performa 450,460, 600 CD Quadra -orCentris (revision B) 410,430 466,467, 630 Centris 600AV RESOLUTION 61
CP871C144A90 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE: MITSUBISHI DENKI BLD, MARUNOUCHI, TOKYO 100-0005 TELEX J24532 CABLE MELCO TOKYO
