DIAMOND DIGITAL DX-D191P Colour TFT LCD Monitor 19” (43 cm) LCD Panel Size
Copyright 2008, Mitsubishi Electric Australia Pty. Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission.
IMPORTANT SAFETY INSTRUCTIONS ...................................... iii Disclaimer .......................................................................................... iv CHAPTER 1 INTRODUCTION....................................................... 5 1.1 Product Description ............................................................... 5 1.2 Product Features .................................................................... 5 1.3 Package Contents ..................................................
CHAPTER 6 WARRANTY ........................................................... 20 After Sales Service ..................................................................... 20 Warranty Does NOT Cover: ....................................................... 20 Service Contacts ........................................................................
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Disclaimer Mitsubishi Electric Australia Pty. Ltd. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Mitsubishi Electric Australia reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
CHAPTER 1 INTRODUCTION Thank you for choosing the Diamond Digital DX-D191P LCD monitor. Your LCD monitor is safe to use and completely free from any X-ray radiation. We hope you enjoy using our product, and would like to provide the following additional information to assist you in obtaining the best results, using the product safely and in complete comfort. Please follow ALL instructions and cautions carefully before using this product. And keep this user manual handy for future reference. 1.
1.3 Package Contents Standard package includes the following: 1. 2. 3. 4. 19" TFT LCD Monitor. (Depend on the screen diagonal) Power Adapter. Signal Cable. (VGA Cable) User Manual. 1.4 Product Care 1. To remove dust or dirt from the screen, use a soft clean cotton cloth and wipe gently. 2. Do not apply pressure to the screen surface while wiping. 3. Do not use any water or chemical detergent to clean the surface. Chemicals detergent may damage the surface of the LCD panel. 1.5 Product Dimension 1.
● PRODUCT 1. Do not cover or block the ventilation holes in the back of the monitor case. 2. Do not insert any metal objects into the ventilation holes of the monitor case and be careful not to spill liquids over this product as this could result in severe injury. 3. Unplug the monitor’s power cable if it’s not to be used for a long period of time. 4. Do not attempt to dismantle this product.
● POWER CORD AND SIGNAL CABLE 1. Do not place anything on the power cord or signal cable. 2. Do not allow any cables from the monitor to lie on the floor in an area where pedestrians are likely to trip, causing injury. 3. This product is supplied with a 3 line-grounding plug. The grounding plug provides an additional safety feature for anyone using this equipment and should not be removed.
CHAPTER 2 OPERATION INSTRUCTIONS 2.1 Front Control Panel 1. Power Switch: press to switch monitor on / off. 2. LED Indicator: power indicator. 3. Mode: press to select input signal. (See ※ Note) 4. Auto: VGA signal auto adjustment. 5. Plus (+): press to increase the value of OSD option selected; press to increase volume. 6. Minus (-): press to decrease the value of OSD option selected; press to decrease volume. 7. Up (Contrast): select OSD options upwards; press to adjust contrast. 8.
※ Note: On the first press, the monitor shows OSD of the current signal. Before the OSD disappears, press the button again to change the input signal source. 2.2 OSD Menu ● VGA / DVI Signal ※ ※ ※ ※ 1. 2. 3. 4. 5. 6. 7. 8. 9. 10 11. 12. 13. 14. 15. 16. 17. Brightness Contrast H-Position V-Position Clock Phase Colour Temp. User Colour R User Colour G User Colour B OSD H-Pos. OSD V-Pos. Volume PIP PIP Size/Pos. Language Recall 26 25 25 32 25 1 User Colour 51 51 51 25 25 10 Off DEF.
● VIDEO (Composite / S-Video / Component) Signal ※ 1. 2. 3. 4. 5. 6. 7. 8. 9. 10 11. 12. 13. Colour Tint Brightness Contrast Sharpness Volume H-Position Language Colour Temp. Scan PIP PIP Size/Pos. Recall 30 26 26 25 4 10 25 English Standard Over Off DEF. Hot Key ※ The Colour Temp. Dependent on the region. Above Value / data is for reference only.
2.3 OSD Function Table ● VGA / DVI 1. 2. 3. 4. 5. 6. Brightness Contrast H-Position V-Position Clock Phase 7. Colour Temp. 8. 9. 10. 11. 12. 13. User Colour R User Colour G User Colour B OSD H-Pos. OSD V-Pos. Volume 14. PIP 15. PIP Size/Pos. 16. Language 17. Recall Adjust back ground black level of the screen image. Adjust fore ground white level of the screen image. Adjust the left or right position of the screen image. Adjust the up or down position of the screen image.
● VIDEO (Composite / S-Video / Component) 1. 2. 3. 4. 5. 6. 7. Colour Tint Brightness Contrast Sharpness Volume H-Position 8. Language 9. Colour Temp. 10. Scan 11. PIP 12. PIP Size/Pos. 13. Recall Adjust the colour density. Adjust the colour tint. (NTSC only) Adjust back ground black level of the screen image. Adjust fore ground white level of the screen image. Adjust the clarity and focus of the screen image. Adjust the volume control. Adjust the left or right position of the screen image.
2.4 Input Signal Icon VGA Signal DVI Signal Composite Signal S-VIDEO Signal Component Signal 2.
CHAPTER 3 SIGNAL CONNECTOR AND INSTRUCTION Input / Output Interface 1. DC In 2. DC Out: DC 12V / MAX. 1A. 3. VGA In 4. VIDEO In / Out (BNC-TYPE) 5. Y/C In / Out (4-Pin mini-Din) S-Video 6. Audio In / Out (RCA Jack) If you choose a video input without connecting any video signal, “No Signal" will be displayed onto the screen. If a video cable is disconnected while the display is being used, “Video Loss " will be displayed onto the screen. Note: ※ It takes about 2 ~ 3 seconds to switch between modes.
Caution: AVOID directly pulling any cables, when disconnecting devices from the monitor. Always disconnect devices carefully by firmly gripping the metal or plastic connector body and gently easing the connector from its socket. CHAPTER 4 VIEWING ANGLE For the user’s convenience, the LCD screen may be tilted according to viewing requirements. The monitor can be tilted forward up to 5 degrees or backward up to 40 degrees.
● RAK191 - RACK MOUNTING BRACKET【OPTIONAL】 ● CM191 - CEILING MOUNTING BRACKET【OPTIONAL】 17
● WB-191 - WALL MOUNTING BRACKET【OPTIONAL】 ● Base Dismounting Process (Step 1) Remove the Hinge Cover (1-1) Insert a thin tool into the hole of the hinge cover, then pull upward and outward to remove the cover. . (1-2) Pull the cover outward 4~5 mm as indicated by arrow A, then pull the cover upward as indicated by arrow B, then remove the cover.
CHAPTER 5 PANEL SPECIFICATION Please refer to attach specification sheet. MODEL 19" Pixel pitch (H x V mm) 0.294 x 0.294. VGA / DVI Max. Resolution VIDEO 1280 x 1024 pixels. Dimension (W x H x D mm) Packing Dimension (W x H x D mm) Display Mode Signal Connector Front Control Panel Buttons 500TVL. 421.2 x 405.6 x 170.0 553.0 x 534.0 x 242.0 VGA、DVI、Composite、S-VIDEO、Component. DC In/Out, VGA In, DVI In【OPTION】, BNC In/Out, Y/C In/Out, Y Cb Cr In【OPTION】, Audio In/Out.
CHAPTER 6 WARRANTY After Sales Service After this product is unpacked, keep the carton and packing materials to ensure safe transportation in case of any after sales service. The warranty is covered by a 3 year limited warranty, subject to normal conditions of use. If you experience any problems with this product please contact your local dealer or supplier for repair and maintenance instructions.
Service Contacts Australian Service Contacts Visit the Customer Support page of Mitsubishi Electric Australia’s web site at; www.mitsubishielectric.com.
South Australia and Northern Territory 77 Port Road Hindmarsh, SA, 5007 Telephone: (08) 8340-0444 Fax: (08) 8340-0555 Victoria and Tasmania 4 / 303 Burwood Hwy East Burwood, VIC, 3151 Telephone: (03) 9262-9899 Fax: (03) 9262-9850 Western Australia 5 / 329 Collier Road Bassendean, WA, 6054 Telephone: (08) 9377-3411 Fax: (08) 9377-3499 22
