Specifications

II Parameters
User Parameters
II - 10
【#8156】 Fine thread cut E
Select the address E type when cutting an inch screw.
(The same value as "#1229 set01/bit1" will be reflected. When either setting changes, the
other will change accordingly.)
0: Specify the number of threads per inch for inch screw cutting.
1: Specify the precision lead for inch screw cutting.
【#8157】 Radius comp type B (M system) / Nose R comp type B (L system)
For M system
Select the method of the arithmetic processing for the intersection point when the start-up or
cancel commands are operated during radius compensation.
(The same value as "#1229 set01/bit2" will be reflected. When either setting changes, the
other will change accordingly.)
0: The processing does not handle the start-up or cancel command block: handle the
offset vector in the direction vertical to that of the command instead.
1: The processing is executed for the intersection point between the command block
and the next block.
For L system
Select the method of the arithmetic processing for the intersection point when the start-up or
cancel commands are operated during nose R or radius compensation.
(The same value as "#1229 set01/bit2" will be reflected. When either setting changes, the
other will change accordingly.)
0: The processing does not handle the start-up or cancel command block: handle the
offset vector in the direction vertical to that of the command instead.
1: The processing is executed for the intersection point between the command block
and the next block.
【#8158】 Init const sur spd
Select the initial state after power-ON.
(The same value as "#1229 set01/bit3" will be reflected. When either setting changes, the
other will change accordingly.)
0: Constant surface speed control cancel mode.
1: Constant surface speed control mode.
【#8159】 Synchronous tap
Select whether to use the floating tap chuck in G74 and G84 tap cycles.
(The same value as "#1229 set01/bit4" will be reflected. When either setting changes, the
other will change accordingly.)
0: With a floating tapping chuck
1: Without a floating tapping chuck
【#8160】 Start point alarm
Select an operation when the operation start point cannot be found while moving to the next
block of G117.
(The same value as "#1229 set01/bit5" will be reflected. When either setting changes, the
other will change accordingly.)
0: The auxiliary function is enabled after the block for the movement has finished.
1: The program error (P33) occurs.
【#8173】 Hold intr amount
Select whether to clear or hold the interruption amount after the "NC reset 1 (or 2)" signal is
ON when the manual ABS switch is OFF.
0: Clear (Reset the coordinate deviation due to the interruption)
1: Hold
【#8201】 AX. RELEASE
Select the function to remove the control axis from the control target.
0: Control as normal.
1: Remove from control target.
【#8202】 OT-CHECK OFF
Select whether to enable the stored stroke limit II function set in #8204 and #8205.
0: Enable
1: Disable
【#8203】 OT-CHECK-CANCEL
When the simple absolute position method ("#2049 type" is "9") is selected, the stored
stroke limits I, II (or IIB) and IB can be disabled until the first reference position return is
executed after the power is turned ON.
0: Enable (according to #8202)
1: Temporarily cancel
(Note) "#8203 OT-CHECK-CANCEL" affects all the stored stroke limits.
【#8204】 OT-CHECK-N
Set the coordinates of the (-) direction in the movable range of the stored stroke limit II or
the lower limit coordinates of the prohibited range of stored stroke limit IIB.
If the sign and value are the same as #8205, the stored stroke limit II (or IIB) will be invalid.
If the stored stroke limit IIB function is selected, the prohibited range will be between two
points even when #8204 and #8205 are set in reverse. When II is selected, the entire range
will be prohibited if #8204 and #8205 are set in reverse.
---Setting range---
-99999.999 to 99999.999 (mm)