Specifications

III PLC Devices
Bit Type Output Signals (PLC->CNC)
Device
A
bbrev. Si
g
nal name
Y1048 TAL14 Tool alarm 1 / Tool-ski
p
$4
Y1049 TAL24 Tool alarm 2 $4
Y104A TCEF4 Usage data count valid $4
Y104B TLF14 Tool life management input $4
Y104C TRST4 Tool change reset $4
Y104D Tool escape and return transit point designation $4
Y104E Manual tool length measurement interlock temporarily canceled $4 ▲
Y1050 ZSL14 Reference position selection code 1 $4
Y1051 ZSL24 Reference position selection code 2 $4
Y1052
Tool length compensation along the tool axis compensation amount
chan
g
e mode $4
Y1053 RTNST4 Tool retract and return 2 : Tool return start $4 ▲
Y1055 In balance cut timing synchronization invalid $4 ▲
Y1057 Reference position selection method $4
Y105D Manual s
p
eed command valid $4
Y105E Manual speed command sign reversed $4
Y105F Manual speed command reverse run valid $4
Y1060 CX114 Manual arbitrary feed 1st axis selection code 1 $4
Y1061 CX124 Manual arbitrary feed 1st axis selection code 2 $4
Y1062 CX144 Manual arbitrary feed 1st axis selection code 4 $4
Y1063 CX184 Manual arbitrary feed 1st axis selection code 8 $4
Y1064 CX1164 Manual arbitrary feed 1st axis selection code 16 $4
Y1067 CX1S4 Manual arbitrary feed 1st axis valid $4
Y1068 CX214 Manual arbitrary feed 2nd axis selection code 1 $4
Y1069 CX224 Manual arbitrary feed 2nd axis selection code 2 $4
Y106A CX244 Manual arbitrary feed 2nd axis selection code 4 $4
Y106B CX284 Manual arbitrary feed 2nd axis selection code 8 $4
Y106C CX2164 Manual arbitrary feed 2nd axis selection code 16 $4
Y106F CX2S4 Manual arbitrary feed 2nd axis valid $4
Y1070 CX314 Manual arbitrary feed 3rd axis selection code 1 $4
Y1071 CX324 Manual arbitrary feed 3rd axis selection code 2 $4
Y1072 CX344 Manual arbitrary feed 3rd axis selection code 4 $4
Y1073 CX384 Manual arbitrary feed 3rd axis selection code 8 $4
Y1074 CX3164 Manual arbitrary feed 3rd axis selection code 16 $4
Y1077 CX3S4 Manual arbitrary feed 3rd axis valid $4
Y1078 CXS14 Manual arbitrary feed smoothing off $4
Y1079 CXS24 Manual arbitrary feed axis independent $4
Y107
A
CXS34 Manual arbitrar
y
feed EX.F / MODAL.F $4
Y107B CXS44 Manual arbitrar
y
feed G0 / G1 $4
Y107C CXS54 Manual arbitrar
y
feed MC / WK $4
Y107D CXS64 Manual arbitrar
y
feed ABS / INC $4
Y107E *CXS74 Manual arbitrary feed stop $4
Y107F CXS84 Manual arbitrary feed strobe $4
Y1080 ILM14 Current limit mode 1 $4
Y1081 ILM24 Current limit mode 2 $4
Y1083 LDWT4 Load monitor I : Teaching / Monitor execution $4 ▲
Y1084 Load monitor I : Teaching mode $4 ▲
Y1085 Load monitor I : Monitor mode $4 ▲
Y1086 Load monitor I : Alarm reset $4
Y1087 Load monitor I : Warning reset $4 ▲
Y1088 *ZRIT4 2nd reference position return interlock $4
Y1089 Load monitor I : Adaptive control execution $4 ▲
Y108A Small diameter deep hole drilling cycle $4
Y108B Chuck barrier on $4
Y108C High-speed retract function valid $4 ▲
Y108F Tool retract start $4 ▲
Y1090 Waiting ignore $4
Y1091 Spindle-spindle polygon cancel $4
Y1092 Synchronous tapping command polarity reversal $4
Y1093 Spindle off mode $4
Y1094 Longitudinal hole drilling axis selection $4
Y1095
Optimum acceleration / deceleration parameter switching request [axis]
$4 ▲
Y1096 TRVEC4 Tap retract possible state cancel $4
Y1097 CHPRCR4 Cho
pp
in
g
com
p
ensation u
p
date
p
revention re
q
uest $4
Y1098 Barrier valid (left) $4
Y1099 Barrier valid (right) $4
Y109A Tool presetter sub-side valid $4 ▲
Y109E HOBRTR4 Hob machinin
g
: retract re
q
uest $4
Y109F HOBARTC4 Hob machinin
g
: alarm retract control $4
Y10A1 Door open II $4
Y10A2
Door open signal input (spindle speed monitor) $4
Y10A3 Door interlock spindle speed clamp $4 ▲
Y10A8 Door open II (2 channels per 1 part system) $4
Ⅲ - 77