Specifications

III PLC Devices
Bit Type Output Signals (PLC->CNC)
Device
A
bbrev. Si
g
nal name
YF2C CX2163 Manual arbitrary feed 2nd axis selection code 16 $3
YF2F CX2S3 Manual arbitrary feed 2nd axis valid $3
YF30 CX313 Manual arbitrary feed 3rd axis selection code 1 $3
YF31 CX323 Manual arbitrary feed 3rd axis selection code 2 $3
YF32 CX343 Manual arbitrary feed 3rd axis selection code 4 $3
YF33 CX383 Manual arbitrary feed 3rd axis selection code 8 $3
YF34 CX3163 Manual arbitrary feed 3rd axis selection code 16 $3
YF37 CX3S3 Manual arbitrary feed 3rd axis valid $3
YF38 CXS13 Manual arbitrary feed smoothing off $3
YF39 CXS23 Manual arbitrary feed axis independent $3
YF3
A
CXS33 Manual arbitrar
y
feed EX.F / MODAL.F $3
YF3B CXS43 Manual arbitrar
y
feed G0 / G1 $3
YF3C CXS53 Manual arbitrar
y
feed MC / WK $3
YF3D CXS63 Manual arbitrar
y
feed ABS / INC $3
YF3E *CXS73 Manual arbitrary feed stop $3
YF3F CXS83 Manual arbitrary feed strobe $3
YF40 ILM13 Current limit mode 1 $3
YF41 ILM23 Current limit mode 2 $3
YF43 LDWT3 Load monitor I : Teaching / Monitor execution $3 ▲
YF44 Load monitor I : Teaching mode $3 ▲
YF45 Load monitor I : Monitor mode $3 ▲
YF46 Load monitor I : Alarm reset $3
YF47 Load monitor I : Warning reset $3 ▲
YF48 *ZRIT3 2nd reference position return interlock $3
YF49 Load monitor I : Adaptive control execution $3 ▲
YF4A Small diameter deep hole drilling cycle $3
YF4B Chuck barrier on $3
YF4C High-speed retract function valid $3 ▲
YF4F Tool retract start $3 ▲
YF50 Waiting ignore $3
YF51 Spindle-spindle polygon cancel $3
YF52 Synchronous tapping command polarity reversal $3
YF53 Spindle off mode $3
YF54 Longitudinal hole drilling axis selection $3
YF55
Optimum acceleration / deceleration parameter switching request [axis]
$3 ▲
YF56 TRVEC3 Tap retract possible state cancel $3
YF57 CHPRCR3 Cho
pp
in
g
com
p
ensation u
p
date
p
revention re
q
uest $3
YF58 Barrier valid (left) $3
YF59 Barrier valid (right) $3
YF5A Tool presetter sub-side valid $3 ▲
YF5E HOBRTR3 Hob machinin
g
: retract re
q
uest $3
YF5F HOBARTC3 Hob machinin
g
: alarm retract control $3
YF61 Door open II $3
YF62
Door open signal input (spindle speed monitor) $3
YF63 Door interlock spindle speed clamp $3 ▲
YF68 Door open II (2 channels per 1 part system) $3
YF6F Load monitor I : Cuttin
g
tor
q
ue estimation execution $3
YF74 BCHK3 Barrier check invalid $3
YF7A DRNC3 Dry run invalid $3
YF7D G71 Shape judgement disable $3 ▲
YF7E Appropriate machining diagnosis in progress $3 ▲
YF7F Appropriate machining diagnosis error reset $3 ▲
YF88 RVSP3 Reverse run from block start $3
YF89 RVIT3 Macro interrupt priority $3
YF8A RVMD3 Reverse run control mode $3
YF8B
A
CCG3 Ra
p
id traverse time constant : Switchover re
q
uest $3
YF94 3D coordinate conversion : Manual feed coordinates conversion $3 ▲
YF98 MJCT3
Manual feed for 5-axis machining (JOG, INC) in tool axis coordinate
s
y
stem $3
YF99 MJCB3
Manual feed for 5-axis machining (JOG, INC) in table coordinate
s
y
stem $3
YF9A MJCF3
Manual feed for 5-axis machining (JOG, INC) in feature coordinate
s
y
stem $3
YF9B MH1CT3
Manual feed for 5-axis machining (1st handle) in tool axis coordinate
s
y
stem $3
YF9C MH1CB3
Manual feed for 5-axis machining (1st handle) in table coordinate
s
y
stem $3
YF9D MH1CF3
Manual feed for 5-axis machining (1st handle) in feature coordinate
s
y
stem $3
YF9E MH2CT3
Manual feed for 5-axis machining (2nd handle) in tool axis coordinate
s
y
stem $3
YF9F MH2CB3
Manual feed for 5-axis machining (2nd handle) in table coordinate
s
y
stem $3
Ⅲ - 74