Specifications

III PLC Devices
Bit Type Output Signals (PLC->CNC)
Device
A
bbrev. Si
g
nal name
YDA7 FVS2 Cutting feedrate override method selection $2
YDA8 ROV12 Rapid traverse override code 1 $2
YDA9 ROV22 Rapid traverse override code 2 $2
YDAF ROVS2 Rapid traverse override method selection $2
YDB0 *JV12 Manual feedrate code 1 $2
YDB1 *JV22 Manual feedrate code 2 $2
YDB2 *JV42 Manual feedrate code 4 $2
YDB3 *JV82 Manual feedrate code 8 $2
YDB4 *JV162 Manual feedrate code 16 $2
YDB7 JVS2 Manual feedrate method selection $2
YDB8 PCF12 Feedrate least increment code 1 $2
YDB9 PCF22 Feedrate least increment code 2 $2
YDBB JHAN2 Jog handle synchronous $2
YDBC Each axis manual feedrate B valid $2
YDBD Manual feedrate B surface speed control valid $2
YDBE Circular feed in manual mode valid $2
YDC0 MP12
Handle / incremental feed ma
g
nification code 1 $2
YDC1 MP22
Handle / incremental feed ma
g
nification code 2 $2
YDC2 MP42
Handle / incremental feed ma
g
nification code 4 $2
YDC6 Magnification valid for each handle $2
YDC7
MPS2 Handle / incremental feed ma
g
nification method selection $2
YDC8 TAL12 Tool alarm 1 / Tool-ski
p
$2
YDC9 TAL22 Tool alarm 2 $2
YDCA TCEF2 Usage data count valid $2
YDCB TLF12 Tool life management input $2
YDCC TRST2 Tool change reset $2
YDCD Tool escape and return transit point designation $2
YDCE Manual tool length measurement interlock temporarily canceled $2 ▲
YDD0 ZSL12 Reference position selection code 1 $2
YDD1 ZSL22 Reference position selection code 2 $2
YDD2
Tool length compensation along the tool axis compensation amount
chan
g
e mode $2
YDD3 RTNST2 Tool retract and return 2 : Tool return start $2 ▲
YDD5 In balance cut timing synchronization invalid $2 ▲
YDD7 Reference position selection method $2
YDDD Manual s
p
eed command valid $2
YDDE Manual speed command sign reversed $2
YDDF Manual speed command reverse run valid $2
YDE0 CX112 Manual arbitrary feed 1st axis selection code 1 $2
YDE1 CX122 Manual arbitrary feed 1st axis selection code 2 $2
YDE2 CX142 Manual arbitrary feed 1st axis selection code 4 $2
YDE3 CX182 Manual arbitrary feed 1st axis selection code 8 $2
YDE4 CX1162 Manual arbitrary feed 1st axis selection code 16 $2
YDE7 CX1S2 Manual arbitrary feed 1st axis valid $2
YDE8 CX212 Manual arbitrary feed 2nd axis selection code 1 $2
YDE9 CX222 Manual arbitrary feed 2nd axis selection code 2 $2
YDEA CX242 Manual arbitrary feed 2nd axis selection code 4 $2
YDEB CX282 Manual arbitrary feed 2nd axis selection code 8 $2
YDEC CX2162 Manual arbitrary feed 2nd axis selection code 16 $2
YDEF CX2S2 Manual arbitrary feed 2nd axis valid $2
YDF0 CX312 Manual arbitrary feed 3rd axis selection code 1 $2
YDF1 CX322 Manual arbitrary feed 3rd axis selection code 2 $2
YDF2 CX342 Manual arbitrary feed 3rd axis selection code 4 $2
YDF3 CX382 Manual arbitrary feed 3rd axis selection code 8 $2
YDF4 CX3162 Manual arbitrary feed 3rd axis selection code 16 $2
YDF7 CX3S2 Manual arbitrary feed 3rd axis valid $2
YDF8 CXS12 Manual arbitrary feed smoothing off $2
YDF9 CXS22 Manual arbitrary feed axis independent $2
YDF
A
CXS32 Manual arbitrar
y
feed EX.F / MODAL.F $2
YDFB CXS42 Manual arbitrar
y
feed G0 / G1 $2
YDFC CXS52 Manual arbitrar
y
feed MC / WK $2
YDFD CXS62 Manual arbitrar
y
feed ABS / INC $2
YDFE *CXS72 Manual arbitrary feed stop $2
YDFF CXS82 Manual arbitrary feed strobe $2
YE00 ILM12 Current limit mode 1 $2
YE01 ILM22 Current limit mode 2 $2
YE03 LDWT2 Load monitor I : Teaching / Monitor execution $2 ▲
YE04 Load monitor I : Teaching mode $2 ▲
YE05 Load monitor I : Monitor mode $2 ▲
YE06 Load monitor I : Alarm reset $2
YE07 Load monitor I : Warning reset $2 ▲
YE08 *ZRIT2 2nd reference position return interlock $2
YE09 Load monitor I : Adaptive control execution $2 ▲
YE0A Small diameter deep hole drilling cycle $2
Ⅲ - 70