Specifications

III PLC Devices
Bit Type Input Signals (CNC->PLC)
Device
A
bbrev. Si
g
nal name
X19B4 SSRI4 In spindle reverse run 4th-Spindle
X19B5 Z phase passed 4th-Spindle
X19B6 SIMP4 Position loop in-position 4th-Spindle
X19B7 STLQ4 In spindle torque limit 4th-Spindle
X19BD SD24 Speed detection 2 4th-Spindle
X19BE MCSA4 In M coil selection 4th-Spindle
X19BF Index positioning completion 4th-Spindle
X19C0 ENB4 Spindle enable 4th-Spindle
X19C1 LRUC4 In changeover to L coil 4th-Spindle ▲
X19C2 HRUC4 In changeover to H coil 4th-Spindle ▲
X19C7 Spindle synchronization speed detect 4th-Spindle ▲
X19C8 SPSYN14 In spindle synchronization 4th-Spindle
X19C9 FSPRV4 Spindle rotation speed synchronization completion 4th-Spindle
X19CA FSPPH4 Spindle phase synchronization completion 4th-Spindle
X19CB SPSYN24 In spindle synchronization 2 4th-Spindle
X19CC SPCMP4 Chuck close confirmation 4th-spindle
X19CE SPSYN34 In tool spindle synchronization II 4th-spindle
X19D3 PHOVR4 Hob axis delay excess 4th-spindle
X19D5 EXOFN4 In spindle holding force up 4th-spindle
X19D6 SPOFFA4 Spindle being excluded 4th-Spindle
X1A02 SIGE5 S command gear No. illegal 5th-Spindle
X1A03 SOVE5 S command max. / min. command value over 5th-Spindle
X1A04 SNGE5 S command no gear selected 5th-Spindle
X1A05 GR15 Spindle gear shift command 1 5th-Spindle
X1A06 GR25 Spindle gear shift command 2 5th-Spindle
X1A07 (Always "0") 5th-Spindle
X1A08 Spindle 2nd in-position 5th-Spindle
X1A09 CDO5 Current detection 5th-Spindle
X1A0A VRO5 Speed detection 5th-Spindle
X1A0B FLO5 In spindle alarm 5th-Spindle
X1A0C ZSO5 Zero speed 5th-Spindle
X1A0D USO5 Spindle up-to-speed 5th-Spindle
X1A0E ORAO5 Spindle in-position 5th-Spindle
X1A0F LCSA5 In L coil selection 5th-Spindle
X1A10 SMA5 Spindle ready-ON 5th-Spindle
X1A11 SSA5 Spindle servo-ON 5th-Spindle
X1A12 SEMG5 In spindle emergency stop 5th-Spindle
X1A13 SSRN5 In spindle forward run 5th-Spindle
X1A14 SSRI5 In spindle reverse run 5th-Spindle
X1A15 Z phase passed 5th-Spindle
X1A16 SIMP5 Position loop in-position 5th-Spindle
X1A17 STLQ5 In spindle torque limit 5th-Spindle
X1A1D SD25 Speed detection 2 5th-Spindle
X1A1E MCSA5 In M coil selection 5th-Spindle
X1A1F Index positioning completion 5th-Spindle
X1A20 ENB5 Spindle enable 5th-spindle
X1A21 LRUC5 In changeover to L coil 5th-Spindle ▲
X1A22 HRUC5 In changeover to H coil 5th-Spindle ▲
X1A27 Spindle synchronization speed detect 5th-Spindle ▲
X1A28 SPSYN15 In spindle synchronization 5th-Spindle
X1A29 FSPRV5 Spindle rotation speed synchronization completion 5th-Spindle
X1A2A FSPPH5 Spindle phase synchronization completion 5th-Spindle
X1A2B SPSYN25 In spindle synchronization 2 5th-Spindle
X1A2C SPCMP5 Chuck close confirmation 5th-spindle
X1A2E SPSYN35 In tool spindle synchronization II 5th-spindle
X1A33 PHOVR5 Hob axis delay excess 5th-spindle
X1A35 EXOFN5 In spindle holding force up 5th-spindle
X1A36 SPOFFA5 Spindle being excluded 5th-Spindle
X1A62 SIGE6 S command gear No. illegal 6th-Spindle
X1A63 SOVE6 S command max. / min. command value over 6th-Spindle
X1A64 SNGE6 S command no gear selected 6th-Spindle
X1A65 GR16 Spindle gear shift command 1 6th-Spindle
X1A66 GR26 Spindle gear shift command 2 6th-Spindle
X1A67 (Always "0") 6th-Spindle
X1A68 Spindle 2nd in-position 6th-Spindle
X1A69 CDO6 Current detection 6th-Spindle
X1A6A VRO6 Speed detection 6th-Spindle
X1A6B FLO6 In spindle alarm 6th-Spindle
X1A6C ZSO6 Zero speed 6th-Spindle
X1A6D USO6 Spindle up-to-speed 6th-Spindle
X1A6E ORAO6 Spindle in-position 6th-Spindle
X1A6F LCSA6 In L coil selection 6th-Spindle
X1A70 SMA6 Spindle ready-ON 6th-Spindle
Ⅲ - 23