Specifications

III PLC Devices
Bit Type Input Signals (CNC->PLC)
Device
A
bbrev. Si
g
nal name
XDEA
Optimum acceleration / deceleration parameter switch completion [axis]
$2 ▲
XDEB ESTSVIN2
Optimum acceleration / deceleration selection : NC axis inertia
estimation in
p
ro
g
ress $2 ▲
XDEC GETSVAF2
Optimum acceleration / deceleration selection : NC axis estimated
resonance fre
q
uenc
y
ac
q
uisition in
p
ro
g
ress $2 ▲
XDEE HOBRTM2 Hob machining : retracting $2
XDEF HOBRTF2 Hob machining : retract complete $2
XDF0 In Spindle-NC axis polygon mode $2
XDF1 AL52 NC alarm 5 $2
XDF2 In Spindle-Spindle polygon mode $2
XDF3 Spindle-spindle polygon synchronization completion $2
XDF9 In 3-dimensional coordinate conversion $2
XE00 RTAP2 In synchronized tapping selection (M command) $2
XE01 In small diameter deep hole cycle $2
XE02 High-speed retract function valid state $2 ▲
XE03 In high-speed retract function operation $2 ▲
XE08 In barrier valid (left) $2
XE09 In barrier valid (right) $2
XE0A TLMSFIN2 Tool length measurement completion $2 ▲
XE0B TLMSERR2 Tool length measurement error $2 ▲
XE0E
TLMSSELO
2
Tool length measurement sub-side selected $2 ▲
XE0F Tool retract position reached $2 ▲
XE10 TRME2 With tool retract amount command $2 ▲
XE11 TRRP2 In tool repositioning $2 ▲
XE18 Door open enable $2
XE28 Door open enable (2 channels per 1 part system) $2
XE2D Optimum machining diagnosis in progress $2 ▲
XE2E Load monitor I : Cutting torque estimation in progress $2
XE2F Load monitor I : Cuttin
g
tor
q
ue estimation com
p
leted $2
XE4B G0AC2 Ra
p
id traverse time constant : In switchover $2
XE54 3D coordinate conversion : Manual feed valid $2 ▲
XE58 MJST2
Tool axis coordinate system in manual feed for 5-axis machining (JOG,
INC
)
$2
XE59 MJSB2
Table coordinate system in manual feed for 5-axis machining (JOG,
INC
)
$2
XE5A MJSF2
Feature coordinate system in manual feed for 5-axis machining (JOG,
INC
)
$2
XE5B MH1ST2
Tool axis coordinate system in manual feed for 5-axis machining (1st
handle
)
$2
XE5C MH1SB2
Table coordinate system in manual feed for 5-axis machining (1st
handle
)
$2
XE5D MH1SF2
Feature coordinate system in manual feed for 5-axis machining (1st
handle
)
$2
XE5E MH2ST2
Tool axis coordinate system in manual feed for 5-axis machining (2nd
handle
)
$2
XE5F MH2SB2
Table coordinate system in manual feed for 5-axis machining (2nd
handle
)
$2
XE60 MH2SF2
Feature coordinate system in manual feed for 5-axis machining (2nd
handle
)
$2
XE61 MH3ST2
Tool axis coordinate system in manual feed for 5-axis machining (3rd
handle
)
$2
XE62 MH3SB2
Table coordinate system in manual feed for 5-axis machining (3rd
handle
)
$2
XE63 MH3SF2
Feature coordinate system in manual feed for 5-axis machining (3rd
handle
)
$2
XE67 TCPRS2 In tool center
p
oint rotation $2
XE68 RSSCT2 R-Navi : selectin
g
machine surface $2
XE69 RSIND2 R-Navi : machine surface indexin
g
$2
XE6
A
RSIDF2 R-Navi : machine surface index com
p
lete $2
XE80 JO3 In jog mode $3
XE81 HO3 In handle mode $3
XE82 SO3 In incremental mode $3
XE83 PTPO3 In manual arbitrary feed mode $3
XE84 ZRNO3 In reference position return mode $3
XE85 ASTO3 In automatic initial set mode $3
XE86 In jog-handle simultaneous mode $3
XE88 MEMO3 In memory mode $3
XE89 TO3 In tape mode $3
XE8A In online operation mode $3
XE8B DO3 In MDI mode $3
XE90 MA3 Controller ready completion $3
XE91 SA3 Servo ready completion $3
XE92 OP3 In automatic operation "run" $3
Ⅲ - 16