Specifications

II Parameters
Spindle Parameters
II - 160
【#3059】 sptc6 Spindle synchronization multi-step acceleration/deceleration changeover
speed 6
Set the speed which switches from 6th step to 7th step in spindle synchronization multi-step
acceleration/deceleration control. Set the same value for the reference axis and
synchronous axis.
Set the value of limit rotation speed (slimit) or higher not to carry out a step shift.
---Setting range---
0 to 99999 (r/min)
【#3060】 sptc7 Spindle synchronization multi-step acceleration/deceleration changeover
speed 7
Set the speed which switches from 7th step to 8th step in spindle synchronization multi-step
acceleration/deceleration control. Set the same value for the reference axis and
synchronous axis.
Set the value of limit rotation speed (slimit) or higher not to carry out a step shift.
---Setting range---
0 to 99999 (r/min)
【#3061】 spdiv1 Time constant magnification for changeover speed 1
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 1 (sptc1) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3062】 spdiv2 Time constant magnification for changeover speed 2
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 2 (sptc2) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3063】 spdiv3 Time constant magnification for changeover speed 3
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 3 (sptc3) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3064】 spdiv4 Time constant magnification for changeover speed 4
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 4 (sptc4) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3065】 spdiv5 Time constant magnification for changeover speed 5
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 5 (sptc5) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3066】 spdiv6 Time constant magnification for changeover speed 6
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 6 (sptc6) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3067】 spdiv7 Time constant magnification for changeover speed 7
Set the acceleration/deceleration time constant to be used at the speed of changeover
speed 7 (sptc7) and higher in spindle synchronization multi-step acceleration/deceleration
control. Set this as a magnification in relation to the spindle synchronization acceleration/
deceleration time constant (spt).
---Setting range---
0 to 127
【#3068】 symtm1 Phase synchronization start confirmation time
Set the time to confirm that synchronization is attained before spindle phase
synchronization control is started.
When "0" is set, the time will be 500ms. When "100" or less is set, the time will be 100ms.
---Setting range---
0 to 9999 (ms)