Specifications

II Parameters
Spindle Parameters
II - 155
【#3011】 ssift 3 Shift rotation speed (Gear: 10)
Set the spindle speed for gear shifting with gear 10.
(Note) Setting too large value may cause a gear nick when changing gears.
---Setting range---
0 to 32767 (r/min)
【#3012】 ssift 4 Shift rotation speed (Gear: 11)
Set the spindle speed for gear shifting with gear 11.
(Note) Setting too large value may cause a gear nick when changing gears.
---Setting range---
0 to 32767 (r/min)
【#3013】 stap 1 Synchronous tapping 1st step rotation speed (Gear: 00)
Set the speed which switches from 1st step to 2nd step in synchronous tapping multi-step
acceleration/deceleration control when gear 00 is selected.
The inclination of linear acceleration/deceleration control for 1st step is determined by the
ratio of stap1(#3013) to stapt1(#3017).
When the inclination is not set after 2nd step or it is higher than that of 1st step, the
acceleration/deceleration control is executed with the same inclination as the 1st step for
the rotation speed of stap1 or higher.
---Setting range---
0 to 99999 (r/min)
【#3014】 stap 2 Synchronous tapping 1st step rotation speed (Gear: 01)
Set the speed which switches from 1st step to 2nd step in synchronous tapping multi-step
acceleration/deceleration control when gear 01 is selected.
The inclination of linear acceleration/deceleration control for 1st step is determined by the
ratio of stap2(#3014) to stapt2(#3018).
When the inclination is not set after 2nd step or it is higher than that of 1st step, the
acceleration/deceleration control is executed with the same inclination as the 1st step for
the rotation speed of stap2 or higher.
---Setting range---
0 to 99999 (r/min)
【#3015】 stap 3 Synchronous tapping 1st step rotation speed (Gear: 10)
Set the speed which switches from 1st step to 2nd step in synchronous tapping multi-step
acceleration/deceleration control when gear 10 is selected.
The inclination of linear acceleration/deceleration control for 1st step is determined by the
ratio of stap3(#3015) to stapt3(#3019).
When the inclination is not set after 2nd step or it is higher than that of 1st step, the
acceleration/deceleration control is executed with the same inclination as the 1st step for
the rotation speed of stap3 or higher.
---Setting range---
0 to 99999 (r/min)
【#3016】 stap 4 Synchronous tapping 1st step rotation speed (Gear: 11)
Set the speed which switches from 1st step to 2nd step in synchronous tapping multi-step
acceleration/deceleration control when gear 11 is selected.
The inclination of linear acceleration/deceleration control for 1st step is determined by the
ratio of stap4(#3016) to stapt4(#3020).
When the inclination is not set after 2nd step or it is higher than that of 1st step, the
acceleration/deceleration control is executed with the same inclination as the 1st step for
the rotation speed of stap4 or higher.
---Setting range---
0 to 99999 (r/min)
【#3017】 stapt 1 Synchronous tapping 1st step acceleration/deceleration time constant
(Gear: 00)
Set the time constant for synchronous tapping 1st step linear acceleration/deceleration
control when gear 00 is selected. (linear acceleration/deceleration pattern)
---Setting range---
1 to 5000 (ms)
【#3018】 stapt 2 Synchronous tapping 1st step acceleration/deceleration time constant
(Gear: 01)
Set the time constant for synchronous tapping 1st step linear acceleration/deceleration
control when gear 01 is selected. (linear acceleration/deceleration pattern)
---Setting range---
1 to 5000 (ms)
【#3019】 stapt 3 Synchronous tapping 1st step acceleration/deceleration time constant
(Gear: 10)
Set the time constant for synchronous tapping 1st step linear acceleration/deceleration
control when gear 10 is selected. (linear acceleration/deceleration pattern)
---Setting range---
1 to 5000 (ms)