Specifications

II Parameters
Axis Specifications Parameters
II - 117
【#2121】 vbacklash valid Variable backlash valid/continuous or Variable backlash II valid
Select whether the variable backlash is to be disabled/enabled/continuous, or variable
backlash II enabled.
0: Disable
1: Enable
2: Continuous
3: Enable variable backlash II
("#2011 G0back" and "#2012 G1back" will not work unless "0: Disable" is selected. )
【#2122】 G0vback+ Variable G0 backlash +
Set the compensation amount for the range of each position during rapid traverse.
(+: B1, =: B2, -: B3 on the compensation amount table)
---Setting range---
-99999999 to 99999999 (Interpolation unit)
【#2123】 G0vback= Variable G0 backlash =
Set the compensation amount for the range of each position during rapid traverse.
(+: B1, =: B2, -: B3 on the compensation amount table)
---Setting range---
-99999999 to 99999999 (Interpolation unit)
【#2124】 G0vback- Variable G0 backlash -
Set the compensation amount for the range of each position during rapid traverse.
(+: B1, =: B2, -: B3 on the compensation amount table)
---Setting range---
-99999999 to 99999999 (Interpolation unit)
【#2125】 G1vback+ Variable G1 backlash +
Set the compensation amount for the range of each position during cutting feed.
(+: A1, =: A2, -: A3 on the compensation amount table)
---Setting range---
-99999999 to 99999999(Interpolation unit)
【#2126】 G1vback= Variable G1 backlash =
Set the compensation amount for the range of each position during cutting feed.
(+: A1, =: A2, -: A3 on the compensation amount table)
---Setting range---
-99999999 to 99999999 (Interpolation unit)
【#2127】 G1vback- Variable G1 backlash -
Set the compensation amount for the range of each position during cutting feed.
(+: A1, =: A2, -: A3 on the compensation amount table)
---Setting range---
-99999999 to 99999999 (Interpolation unit)
【#2128】 G1vback feed1 G1 variable backlash compensation amount changeover speed 1
Set the speed range during cutting feed.
(The speed less than 1 is the low speed, and the speed exceeding 2 is the high speed.)
Note that the speed range is identified in the order of low, high and medium speed.
Consider whether the set value should be larger or smaller than other values.
---Setting range---
0 to 480000 (mm/min)
【#2129】 G1vback feed2 G1 variable backlash compensation amount changeover speed 2
Set the range of the speed during cutting feed.
(The speed less than 1 is the low speed, and the speed exceeding 2 is the high speed.)
Note that the speed range is identified in the order of low, high and medium speed.
Consider whether the set value should be larger or smaller than other values.
---Setting range---
0 to 480000 (mm/min)
【#2130】 G1vback dist1 G1 variable backlash compensation amount changeover distance 1
Set the range of the distance during cutting feed.
(The distance less than 1 is the small distance, and the distance exceeding 2 is the large
distance.)
Note that the distance range is identified in the order of small, large and medium. Consider
whether the set value should be larger or smaller than other values.
---Setting range---
0 to 999999.999999 (mm)
【#2131】 G1vback dist2 G1 variable backlash compensation amount changeover distance 2
Set the range of the distance during cutting feed.
(The distance less than 1 is the small distance, and the distance exceeding 2 is the large
distance.)
Note that the distance range is identified in the order of small, large and medium. Consider
whether the set value should be larger or smaller than other values.
---Setting range---
0 to 999999.999999 (mm)