Specifications

II Parameters
Base Specifications Parameters
II - 100
【#11022】 SRAM Output Type SRAM output type
Set the SRAM output type.
(Note) In M700 Series, the conventional SRAM output type is set regardless of the setting of
this parameter.
0: The latest SRAM output type is set.
(Not compatible with F3 and versions older than F3.)
1: The conventional SRAM output type is set.
(Compatible with F3 and versions older than F3.)
【#11023】 G33.n Drn G33.n dryrun
Not used.
【#11024】 G33.n fhd G33.n feed hold
Not used.
【#11028】 Tolerance Arc Cent Tolerable correction value of arc center error
Set the tolerable correction value for the calculated coordinate value error of R-specified
circular center.
When a difference between "a line between the start and end points" and "commanded
radius x 2" is the tolerance or smaller, the error is corrected so that the middle of a line
between the start and end points will be the arc center.
When [Setting value < 0] : 0 (Not correct)
When [Setting value = 0] : 2 x minimum setting increment
When [Setting value > 0] : Setting value
---Setting range---
-1 to 0.100(mm)
【#11029】 Arc to G1 no Cent Change command from arc to linear when no arc center
designation
Select the operation when arc center or radius designation is omitted from arc command.
0: Program error
1: Change into linear command
【#11030】 Man tap sync cancl Synchronization cancel in manual synchronous tapping
Select whether the tapping axis in manual synchronous tapping synchronizes with the
spindle.
0: Synchronize with the spindle
1: Not synchronize with the spindle
【#11031(PR)】 Cursor pos search Cursor position search
Select the cursor position searching method.
0: Disable
1: Pressing the INPUT key in [Monitr] - [Edit] menu starts the operation search for the
block with the cursor.
2: Turning ON/OFF the "Edit/Search" signal in [Monitr] - [Edit] menu starts the operation
search for the block with the cursor.
3: Turning ON/OFF the "Edit/Search" signal in [Monitr] - [Edit] menu starts the operation
search for the block with the cursor. Pressing the reset key shows the top of the
program on the [Edit/Search] window.
【#11032(PR)】 Menu sel para lkof Validate menu selection parameter setting
Select whether to enable the setting of the "menu selection parameters" (#10501 to #10530,
#10551 to #10580, and #10601 to #10630), with which the order of main menus on Monitor,
Setup and Edit screens can be rearranged. And also select who is allowed to do this setting.
0: Disable
1: Enable (machine tool builder password is required)
2: Enable (users are allowed to set)
【#11033(PR)】 skipB_no_sens Unconnected sensor selection when skip is set to contact B
Select the contact of the sensor which you wish to set as unconnected, when the skip signal
is set to contact B.
Set "1" for the contact to be unconnected.
bit0: Skip input 1
bit1: Skip input 2
bit2: Skip input 3
bit3: Skip input 4
bit4: Skip input 5
bit5: Skip input 6
bit6: Skip input 7
bit7: Skip input 8
(Note 1)This parameter is enabled when "#1258 set30/bit0" is set to "1".
(Note 2)This parameter is independent of PLC skip.
---Setting range---
00000000 to 11111111 (Binary)
【#11034】 G12AddrCheckType Command address type to check in circular cutting
Select the type of command address to check in circular cutting.
0: Regard command addresses other than D, F, I as illegal.
1: Regard the command address H as illegal. And commands other than D,F,I and
M,S,T,B are disabled.