Specifications

II Parameters
Base Specifications Parameters
II - 95
【#1542】 crsax[6]
Set the axis to be interchanged during the mixed control (cross axis control).
Using two digits, set the name of the axis to be interchanged with the axis in the part system
where the mixed control (cross axis control) request signal is input, or the name of the axis
to be shifted to that part system.
---Setting range---
Two digits between A to Z and 1 to 9
(Setting will be cleared when "0" is set)
【#1543】 crsax[7]
Set the axis to be interchanged during the mixed control (cross axis control).
Using two digits, set the name of the axis to be interchanged with the axis in the part system
where the mixed control (cross axis control) request signal is input, or the name of the axis
to be shifted to that part system.
---Setting range---
Two digits between A to Z and 1 to 9
(Setting will be cleared when "0" is set)
【#1544】 crsax[8]
Set the axis to be interchanged during the mixed control (cross axis control).
Using two digits, set the name of the axis to be interchanged with the axis in the part system
where the mixed control (cross axis control) request signal is input, or the name of the axis
to be shifted to that part system.
---Setting range---
Two digits between A to Z and 1 to 9
(Setting will be cleared when "0" is set)
【#1561】 3Dcdc Switch workpiece coordinate display during 3D coordinate conversion
Select the workpiece coordinate display during 3D coordinate conversion.
0: Workpiece coordinate system
1: G68 program coordinate system
(Note) The special display unit's absolute coordinates also follow this parameter setting.
【#1562】 3Dremc Switch remaining command display during 3D coordinate conversion
Select the remaining command display during 3D coordinate conversion.
0: Workpiece coordinate system
1: G68 program coordinate system
【#1563】 3Dcdrc Switch coordinate reading during 3D coordinate conversion
Select the coordinate system of the workpiece/skip coordinate read value in the 3D
coordinate conversion modal.
0: G68 program coordinate system
1: Workpiece (local) coordinate system
【#1564】 3Dspd Hole drilling speed during 3D coordinate conversion
Select the rapid traverse rate for the hole drilling cycle during 3D coordinate conversion.
0: The cutting feed clamp speed is used.
Other than 0: The set speed is used.
Note that if the rapid traverse rate is exceeded, the speed will be clamped at the rapid
traverse rate.
---Setting range---
0 to 1000000mm/min
【#1565】 helgear Helical machining base axis
Set the base axis for helix angle calculation in helical machining. When no setting, Z axis
will be used.
---Setting range---
Axis name such as X, Y, Z, U, V, W, A, B, and C
【#1566】 3DSelctDrillaxMode Switch drill axis's mode from rapid traverse during 3D
coordinate conversion
Select the rapid traverse mode in non-drilling blocks among a drilling cycle to the cutting
feed mode during 3-dimensional coordinate conversion.
0: Rapid traverse mode. The speed follows the setting of "#2001 rapid".
1: Cutting feed mode. The speed follows the setting of "#1564 3Dspd".
【#1568】 SfiltG1 G01 soft acceleration/deceleration filter
Set the filter time constant for smoothly changing the acceleration rate for the cutting feed
acceleration/deceleration in pre-interpolation acceleration/deceleration.
---Setting range---
0 to 200 (ms)
Notch frequency Hz
Displays the notch frequency(Hz) for the S-pattern filter set in "#1568 SfiltG1 (G01 soft
acceleration/deceleration filter)"
【#1569】 SfiltG0 G00 soft acceleration/deceleration filter
Set the filter time constant for smoothly changing the acceleration rate for the rapid traverse
acceleration/deceleration in pre-interpolation acceleration/deceleration.
---Setting range---
0 to 200 (ms)