Specifications

II Parameters
Base Specifications Parameters
II - 92
【#1418】 M_wait[M255-224] Special operation registration M code
Register an M code (224 to 255) that needs special operation.
Each bit of the setting value corresponds to the M code number.
(Example) To register M05, set 00000020 in #1411.
(Note) Note that the registered M code operation varies according to M_mode (#1401).
---Setting range---
0 to FFFFFFFF (hexadecimal)
【#1493(PR)】 ref_syn Synchronization at zero point initialization
0: Primary axis and second axis determine their zero points individually.
1: The zero points of both primary and secondary axes are determined by initializing the
primary axis' zero point.
The secondary axis moves in perfect synchronization with the primary axis.
Set this to "1" for speed/current command synchronization control.
【#1494(PR)】 dsp_ax_change Axis order of counter display
Set this in order to change the axis order of counter display.
The axes will be displayed in ascending order of the setting values "1" to "8".
However, axis whose setting is "0" will be displayed after axes whose settings are between
"1" and "8" are displayed.
(Note 1) When the same value is set for more than one axis, axis that is displayed on the left
side on the parameter screen will be first displayed.
(Note 2) When both of the mixed control (cross axis control) and interchange coordinate
position display ("1280 ext16/bit2" OFF) are valid, and when there are two or more
valid part systems, this parameter will be ignored.
---Setting range---
1 to 8: Axes are displayed in ascending order.
Other than 1 to 8: Axes are displayed after the display of the axes with setting value "1"
to "8".
【#1495(PR)】 grf_ax_direction Axis travel direction in 2D graphic
Select the axis travel direction in the 2D graphic drawing (trace, check).
If set to 1, the positive/negative directions are reversed.
---Setting range---
0/1
【#1501】 polyax Rotational tool axis number (for L system only)
Set the number of the rotational tool axis used for polygon machining (G51.2). Set "0" when
not using polygon machining (spindle-servo axis), or when using spindle-spindle polygon
machining. A value exceeding the base specification parameter "#1002 axisno" cannot be
specified.
This parameter is valid when the G code system is 6 or 7 (7 or 8 is set in base specification
parameter "#1037 cmdtyp").
【#1502】 G0Ipfg G1 -> G0 deceleration check
Select whether to perform a deceleration check when the travel direction is changed from
G1 to G0.
0: Not perform
1: Perform
【#1503】 G1Ipfg G1 -> G1 deceleration check
Select whether to perform a deceleration check when the travel direction is changed from
G1 to G1.
0: Not perform
1: Perform
【#1505】 ckref2 Second reference position return check
Select whether the check is carried out at the specified position in manual second reference
position return mode upon completion of spindle orientation or at second reference position
return interlock signal.
0: Upon completion of spindle orientation
1: At second reference position return interlock signal
【#1506】 F1_FM Upper limit of F1-digit feedrate
Set the maximum value up to which the F 1-digit feedrate can be changed.
---Setting range---
0 to 1000000 (mm/min)
【#1507】 F1_K F 1-digit feedrate change constant
Set the constant that determines the speed change rate per manual handle graduation in F
1-digit feedrate change mode.
---Setting range---
0 to 32767
【#1510】 DOOR_H Shorten door interlock II axis stop time
Select whether to shorten the time during which the axis is stopped when the door is
opened.
0 : Use the conventional axis stop time.
1 : Shorten the axis stop time.
(Note) When the door interlock II signal is input via a ladder, the conventional axis stop time
will be used.