Specifications
II Parameters
Base Specifications Parameters
II - 57
【#1099】 Treset Cancel tool compensation amount
Select how to handle the tool compensation vector when resetting the system.
0: Clear the tool length and wear compensation vectors when resetting
1: Hold the tool length and wear compensation vectors when resetting
When the values are cleared, the compensation will not be applied. So the axis will be
shifted by the compensation amount in the next compensation operation.
When the values are kept, the compensation will be applied, so the axis will shift the
differential amount of the compensation amount in the next compensation operation.
【#1100】 Tmove Tool compensation
Select when to perform tool length compensation and wear compensation.
0: Compensate when T command is executed.
1: Superimpose and compensate with the travel command in the block where the T
command is located. If there is no travel command in the same block, compensation
will be executed after the travel command is superimposed in the next travel
command block.
2: Compensate the wear amount when the T command is executed. Superimpose and
compensate the tool length compensation amount with the travel command in the
same block. If there is no travel command in the same block, compensation will be
executed after the travel command is superimposed in the next travel command
block.
【#1101】 Tabsmv Tool compensation method
Select the type of travel command when “#1100 Tmove” is set to “1” or “2”.
0: Compensate regardless of the travel command type
1: Compensate only at the travel command in the absolute command
【#1102】 tlm Manual tool length measuring system (for L system only)
Select the measurement method for manual tool measurement l.
0: Align tool with basic point
1: Input measurement results
(Note) Interpreted as “0” when other than “0” or “1” is set.
【#1103】 T_Life Validate life management
Select whether to use the tool life management.
0: Not use
1: Use
【#1104】 T_Com2 Tool command method 2
Select how to handle the tool command in the program when "#1103 T_Life" is set to "1".
0: Handle the command as group No.
1: Handle the command as tool No.
(Note) In the case of the tool life management III, the program tool command will be
handled as the tool No. regardless of the setting.
【#1105】 T_Sel2 Tool selection method 2
Select the tool selection method when "#1103 T_Life" is set to "1".
0: Select in order of registered No. from the tools used in the same group.
1: Select the tool with the longest remaining life from the tools used or unused in the
same group.
【#1106】 Tcount Life management (for L system only)
Select the input method when address N is omitted in inputting the data (G10 L3 command)
for tool life management function II.
0: Time specified input
1: Number of times specified input
【#1107】 Tllfsc Split life management display screen (for L system only)
Set the number of groups to be displayed on the tool life management II (L system) screen.
0: Displayed group count 1, maximum number of registered tools: 16
1: Displayed group count 2, maximum number of registered tools: 8
2: Displayed group count 4, maximum number of registered tools: 4
【#1108】 TlrectM Life management re-count M code (for L system only)
Set the M code for tool life management II (L system) re-count.
---Setting range---
0 to 99
【#1109】 subs_M Validate alternate M code
Select the user macro interrupt with the substitute M code.
0: Disable alternate M code
1: Enable alternate M code
【#1110】 M96_M M96 alternate M code
Set an M code to replace M96 when “#1109 subs_M” is set to “1”.
---Setting range---
3 to 97 (excluding 30)
【#1111】 M97_M M97 alternate M code
Specify an M code to replace M97 when #1109 subs_M is set to 1.
---Setting range---
3 to 97 (excluding 30)