Specifications

I Alarms
Operation Errors (M)
I - 7
M01 No speed set out of soft limit 0160
Details
The axis, without any maximum speed outside of the soft limit range set, was returned from
the outside of the soft limit range.
Remedy
- Correct the "#2021 out_f (Maximum speed outside soft limit range)" setting.
- Correct the soft limit range (with "#2013 OT- (Soft limit I-)" and "#2014 OT+ (Soft limit I+)").
M01 Ill. op during T tip control 0170
Details
Illegal operation was attempted during tool tip center control.
Remedy
- Change the operation mode to the previous one and restart.
M01 Illegal OP in tilted face cut 0185
Details
Any of the following illegal operations was attempted during inclined surface machining mode.
- Manual interrupt
- Handle interrupt in automatic operation
- MDI interrupt
- PLC interrupt
- Arbitrary reverse run
Remedy
- Switch the operation mode back to the previous to remove the cause of this failure.
M01 Interference check invalidated 0200
Details
The 3D machine interference check is invalidated. This alarm is output to NC alarm 5.
Remedy
- Validate all the interference check settings.
- If there is any axis which has not completed zero point return, establish the zero point first.
M01 Machine interference 1 0201
Details
It was judged that an interference occurred in the No.1 step interference check and caused a
deceleration stop.
When machine interference is detected, the interfered part is highlighted (yellow/red) and the
part's name is displayed on the 3D monitor's model display.
Remedy
- Move the axis in a direction which does not cause interference.
- Press RESET to cancel the alarm.
- You can move the axis in the same travel direction as before the interference.
But the axis movement is done using the 2nd step interference check distance.
(In manual operation)
M01 Machine interference 2 0202
Details
It was judged that an interference occurred in the No.2 step interference check and caused a
deceleration stop.
When machine interference is detected, the interfered part is highlighted (red) and the part's
name is displayed on the 3D monitor's model display.
Remedy
- Move the axis in a direction which doesn't cause interference.
- Press RESET to cancel the alarm.
M01 Multi ax for 5-ax manual feed 0230
Details
More than one axis was designated simultaneously in manual mode while the manual feed for
5-axis machining was valid.
Remedy
- Command the manual feed to each axis one by one.
M01 5-ax manual feed coord sys err 0231
Details
- More than one of the three bits for selecting hypothetical coordinate system was turned ON.
- Hypothetical coordinate system was selected while the manual feed for 5-axis machining
was invalidated by the parameter setting.
Remedy
- Check the sequence program.
- Validate the manual feed for 5-axis machining (parameter "#7912 NO_MANUAL").
M01 Illegal op in 5 ax tool R comp 0232
Details
An illegal operation (such as manual interrupt) was attempted during tool radius compensation
for 5-axis machining.
Remedy
- Operations such as manual interrupt are disabled while the tool radius compensation for 5-
axis machining is being performed.
M01 Machining surface operation disabled 0250
Details
Machining surface operation (selection, indexing or cancel) was attempted while the operation
is disabled.
Remedy
- Cancel the other modes so that the inclined surface machining command (G68.2), tool axis
direction control (G53.1) and the inclined surface machining cancel command (G69) can be
issued.
- Wait until the axes stop completely (until the smoothing for all axes reaches zero).
- Perform operation search for machining programs.
M01 Axs travel n/a in manual index 0251
Details
Moving a rotary axis was attempted during manual machining surface indexing, when a man-
ual operation mode other than handle mode was selected.
Remedy
- Change the operation mode to a handle mode before carrying out the manual surface index-
ing.