Specifications

II Parameters
User Parameters
II - 20
【#8920】 3D tool ofs select
Select the method to calculate the drawing position when drawing a solid.
With 3D drawing, the drawing position (tool tip position) is calculated with the method
designated with this parameter, and the image is drawn.
0: For tool radius compensation, use the tool compensation amount set in tool
compensation screen. For tool length, use the value in tool set window. (for tool
length measurement type I)
1: Use the tool compensation amount set in tool compensation screen for both tool
radius and tool length compensation. (for tool length measurement type II)
2: Use the value set in tool set window for both tool radius and tool length
compensation. (for tool length measurement type I)
3: Use the value set in tool set window for both tool radius and tool length
compensation. (for tool length measurement type II)
【#8921】 Mass Edit select
Select the editing mode for the machining programs saved in HD, FD, and memory card.
When the program size is 1.0MB (When "#8910 Edit Undo" is invalid, 2.0MB) or more,
mass-editing will be applied.
0: Regular editing mode
1: Mass-editing mode
【#8922】 T-reg-dup check
Set whether to enable the duplication check in registering tools to magazine pots, and in
setting tool Nos. for spindle/standby.
0: Duplication check valid for all valid magazines
1: Duplication check invalid
2: Duplication check valid only for the selected magazine
【#8923(PR)】 Hide Edit-IO menu
Set whether to enable the edit-in/out menu. When disabled, the edit-input/output menu
won't appear. However, the maintenance-in/out menu is always enabled regardless of this
parameter setting.
0: Enable
1: Disable
【#8924】 MEAS. CONFIRM MSG
Select whether to display a confirming message when attempting to write compensation
data for tool measurement, or coordinate system data for workpiece measurement.
However, the confirmation message will not appear in L system tool measurement simple
mode "#8957 T meas (L)-Simple".
0: Not display a confirming message
1: Display a confirming message
【#8925】 SP on 1st part sys
Set a spindle No. to be displayed on the 1st part system window when 2-part system
simultaneous display is valid. On the 15-type display, 1-part system display can be also
specified.
High-order: Select an upper side spindle No.
Low-order: Select a lower side spindle No.
(Note 1) When "00" is set in 2-part system simultaneous display, spindles will be displayed
in a default order (the 1st spindle on the upper side, the 2nd spindle on the lower
side). When "00" is set in 1-part system display of the 15-type display, all spindles will
be displayed.
(Note 2) If you designate a bigger number than the setting of "#1039 spinno", or either the
high-order or low-order setting is "0", the 1st spindle will be displayed.
(Note 3) If the low-order is set to "F", the spindle speed command value and the actual
rotation number which are specified in the high-order will be displayed.
---Setting range---
High-order: 0 to 6
Low-order: 0 to 6, F
【#8926】 SP on 2nd part sys
Set a spindle No. to be displayed on the 2nd part system window when 2-part system
simultaneous display is valid. On the 15-type display, 1-part system display can be also
specified.
High-order: Select an upper side spindle No.
Low-order: Select a lower side spindle No.
(Note 1) When "00" is set in 2-part system simultaneous display, spindles will be displayed
in a default order (the 1st spindle on the upper side, the 2nd spindle on the lower
side). When "00" is set in 1-part system display of the 15-type display, all spindles will
be displayed.
(Note 2) If you designate a bigger number than the setting of "#1039 spinno", or either the
high-order or low-order setting is "0", the 1st spindle will be displayed.
(Note 3) If the low-order is set to "F", the spindle speed command value and the actual
rotation number which are specified in the high-order will be displayed.
---Setting range---
High-order: 0 to 6
Low-order: 0 to 6, F