User`s manual

ManualsBrandsMitsubishi ManualsComputer equipmentAS120-1

Table 7.17 Data Format (4/8)

Data

Data Format ④

Alarm state 1

(46/n)

LEN130

391

Data

Bit

Content ON(1) OFF(0)

ME96

SSH

ME96

SSR

b16 Digital Input 1 ON OFF ○ ○

b17 Digital Input 2 ON OFF ○ ○

b18 Digital Input 3 ON OFF ○ ○

b19 Digital Input 4 ON OFF ○ ○

b20 Reserved - - - -

b21 Alarm (Total) Non-Alarm Alarm ○ ○

b22 Alarm of Current Demand Non-Alarm Alarm ○ ○

b23 Alarm of Active power Demand Non-Alarm Alarm ○ -

b24 Alarm of Voltage Non-Alarm Alarm ○ ○

b25 Alarm of Current Non-Alarm Alarm ○ ○

b26 Alarm of Active power Non-Alarm Alarm ○ ○

b27 Alarm of Reactive power Non-Alarm Alarm ○ ○

b28 Alarm of Frequency Non-Alarm Alarm ○ ○

b29 Alarm of Power factor Non-Alarm Alarm ○ ○

b30 Alarm of T.H.D (Voltage) Non-Alarm Alarm ○ ○

b31 Alarm of Harmonic current Non-Alarm Alarm ○ ○

Alarm judging items of each phase wiring are shown as follows.

Monitored phase

Upper/lower limit alarm element

3P4W 3P3W(3C

,2CT) 1P3W（1N2） 1P3W（1N3）

Upper limit current, current demand 1, 2, 3 1, 2, 3 1, N, 2 1, N, 3

Lower limit current, current demand 1, 2, 3 1, 2, 3 1, 2 1, 3

Upper limit N-phase current, N-phase current demand N ― ― ―

Lower limit N-phase current, N-phase current demand N ― ― ―

Upper limit voltage (L-L) (*1) 12, 23, 31 12, 23, 31 1N, 2N, 12 1N, 3N, 13

Lower limit voltage (L-L) (*1) 12, 23, 31 12, 23, 31 1N, 2N, 12 1N, 3N, 13

Upper limit voltage (L-N) 1N, 2N, 3N ― ― ―

Lower limit voltage (L-N) 1N, 2N, 3N ― ― ―

Upper limit active power, reactive power, power factor Total Total Total Total

Lower limit active power, reactive power, power factor Total Total Total Total

Upper limit frequency 1N 12 1N 1N

Lower limit frequency 1N 12 1N 1N

Harmonic current total RMS value 1, 2, 3 1, 2, 3 (*2) 1, 2 1, 3

Harmonic current total RMS value N-phase N ― ― ―

Harmonic voltage total distortion ratio 1N, 2N, 3N 12, 23 1N, 2N 1N, 3N

Upper limit rolling demand Total Total Total Total

*1: For phase 12 (or phase 31) at 1-phase 3-wire, alarm monitoring is executed using a value that is two times the

set upper/lower limit alarm value.

*2: Only 3P3W (3CT) is measured for the phase 2 harmonic current.

b15 b8 b7 b0

Format④

Index number

Low data

Unused (00H fixed)

High data

Unused (0000H fixed)

High data

b31 b23

b24 b16

Alarm state