User`s manual

3 - 2
MELSEC-
A
3 SPECIFICATION
3.2 Performance Specification
Table 3.2 indicates the performance specifications of the AJ65SBT-64AD.
Table 3.2 Performance specification
Item Specification
Analog input
Voltage
-10 to 10V DC (input resistance 1M
)
Current
0 to 20mA DC (input resistance 250
)
Digital output 16-bit signed binary (-4096 to 4095)
I/O characteristics, maximum
resolution, accuracy*
1
(accuracy
relative to maximum value of digital
output value)
Analog input range Digital output
Accuracy
Max.
Resolution
Ambient
temperature
0 to 55°C
Ambient
temperature
25±5°C
Voltage
-10 to 10V
-4000 to +4000
±0.4%
(±16 digit*
2
)
±0.2%
(±8 digit*
2
)
2.5mV
User range setting 1
(-10 to 10V)
0 to 5V
0 to 4000
1.25mV
1 to 5V
1.0mV
User range setting 2
(0 to 5V)
Current
0 to 20mA
0 to 4000
5µA
4 to 20mA
4µA
User range setting 3
(0 to 20mA)
Factory setting is -10 to 10V.
Maximum conversion speed 1ms/channel
Absolute maximum input Voltage ±15 V, current ±30mA*
3
Analog input points 4 channels/1 module
CC-Link station type Remote device station
Number of occupied stations 1 station
Communication cable CC-Link dedicated cable
Dielectric withstand voltage Between power supply/communication system batch and analog input batch: 500VAC, 1 minute
Isolation system
Across communication system terminals and all analog input terminals: Photocoupler isolated
Across power supply system terminals and all analog input terminals: Photocoupler isolated
Across channels: Non-isolated
Noise immunity By noise simulator of 500Vp-p noise voltage, 1µs noise width and 25 to 60Hz noise frequency
External
connection
Communication area,
module power supply
7-point 2-piece terminal block [transmission circuit, module power supply, FG]
M3
5.2 Tightening torque: 0.59 to 0.88N·m
Applicable solderless terminals: 2 max.
I/O area
Direct-coupled, 18-point terminal block [analog input area]
M3 5.2 Tightening torque: 0.59 to 0.88N·m
Applicable solderless terminals: 2 max.
Applicable wire size 0.3 to 0.75mm
2
Applicable solderless terminals
RAV1.25-3 (conforming to JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm
2
]
V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm
2
]
Module mounting screw
M4 screw
0.7mm 16mm or more (tightening torque range: 0.78 to 1.08N m)
Can also be mounted to DIN rail
Supported DIN rail TH35-7.5Fe, TH35-7.5Al (conforming to IEC 60715)
External supply power
24V DC (20.4 to 26.4V DC)
Inrush current: 8.5A, within 2.3ms
Current consumption: 0.090A (at 24VDC)
Weight 0.20kg
*1 For the details of the I/O conversion characteristic, refer to Section 3.3.
*2 digit indicates digital value
*3 Current value indicates value of instant input current that does not break module inner electrical resistance.
3