Specifications

56
Modem Interface Modules
■
Q6TEL modem interface unit
Item Specifications
A/QnA conversion switch Set to “QnA” Set to “A”
Applicable CPUs All of the QnA Series All of the A Series
CPU connection method Add-on method
Add-on method for A2CCPU
and A2CJCPU
Local Devices Connection:
Connection cable
User Supplied (Compatible with AC30N2(A))
Modem Connection:
cable included with modem or specified cable
Interface RS232C (Modem or DOS/V computer used for connecting)
Telephone circuit Analog 2 line type, ISDN
Number of notification
items
Pager notification
message length
fixed or variable fixed
Consumption current
(DC5V)
0.15A (current from CPU unit)
Outer dimensions 102(4.02)H× 109(4.29)W× 21(0.83)D mm (inch)
Weight 0.20kg
Software package
SWMD5C-GPPW
(
M: version 3 or higher
)
Model Software Package
■
SW
M
D5C-GPPW
(
M
: version 3 or higher
)
model
●
Telephone Line Restrictions
Because data may be altered or the connection severed
due to an incoming call alert signal, please refrain from
using call waiting.
Because the connection may be severed when a receiver
is picked up, avoid using lines to which multiple phones
are connected.
■
Additional modem information
●
Modem Specifications
Transmission Standards: Transmission speed depends
on the modem
Error Detection: MNP Class 4/10 or V.42
Data Compression: MNP Class 5 or ITU-T V.42bis
NCU Type: AT Command
Both DIP switch and AT command (for use with
terminal software) can be used to independently
change the DR signal to H status.
●
Connection Cable
RS-232C cable included with the modem or specified
cable can be used. (See Performance Specifications)
●
Q6TEL: 25 pins; D sub-connector
●
Personal Computer: 9 pins; D sub-connector
●
When Using a Cell Phone
When the recipient is using a cell phone the error
detection function requires an MNP Class 10 Support
Modem. It may not function properly when the line
quality is poor.
If when using a cell phone, messages are set to be
received automatically, use a transmission unit for cell
phones that can manage such a function.
Item Function
Circuit connection Connect via a telephone circuit to the location you designate.
Circuit disconnection Disconnect the circuit
Telephone number
registration
System settings
Send and receive
files
Prepare data
for Q6TEL
Set the location and telephone number for the connection
being made. A maximum of 250 circuits can be used.
Set the modem used to make the connection and the location
where log files are to be housed.
Send and Receive files between GPP peripheral devices such
as DOS/V computers.
*Not supported by the Q6TEL function.
Configure the connecting modem, password, and
notifications registered with Q6TEL and register with A6TEL.
Q6TEL
Features
●
The QnA/A switch allows for connection to all QnA Series
and A Series sequencer CPUs.
●
Sequencer maintenance via remote access GPP peripheral
devices such as DOS/V personal computers can be
connected with the sequencer via a phone line allowing
monitoring, testing, programming, and other revisions to
be conducted at long distances. GPP peripheral devices
such as DOS/V computers, and the sequencer when
connected by RS-422 operate with the same GPP function.
●
Notification System
When an abnormality occurs in the sequencer or trouble
is detected at the operation facilities, notification and a
message of up to 10 characters will be sent from Q6TEL
to your pager.
●
Password Registration
When you register your password with Q6TEL, only
authorized parties will be allowed remote access.
●
RS-232C–RS-422 Conversion Function
When Q6TEL is installed to the sequencer, peripheral
devices can be connected with RS-232C (See Performance
Specifications) cable making monitoring, testing, program
scheduling and other changes to the GPP function
possible. (An RS232C–RS422 Converter and conversion
cable is not required.)
6 items
(pager notification only)
10 items (Including Q6TEL
transmission)
SWMD5C-GPPW
(
M: version 3 or higher) Model
GPP Software Package or
SW2SRXV/NX/IVD-GPPA Model
GPP Software Package plus
SW2SRXV/NX/IVD-GPPATEL
Model GPP Software Package
SWMD5C-GPPW
(
M: version 2 or higher)
Model GPP Software
Package
RyansElectric.com