Product manual

43
352),%860'3#&RPPXQLFDWLRQV#,QWHUIDFH#0#+$7968948334
,QLWLDO#6HW0XS#IRU#3URILEXV
&RQILJXULQJ#WKH#'ULYH
Using the Operator Station (MMI) or
other suitable PC programming tool,
the TEC OPTION function block
requires configuring before the
PROFIBUS option can be used.
The parameter names/functions in this
function block are inter-dependant and
will change with different parameter
values and the various Options that can
be fitted.
The top Function Block diagram shows
the ConfigEd Lite parameter names,
which are also displayed on the MMI if
no Option is fitted or an incorrect TYPE
is selected for the fitted Option.
ConfigEd Lite is Eurotherm Drives’
Windows-based block programming
software.
When the TYPE parameter is set to
display PROFIBUS, the function block
parameters take on new identities, as shown in the lower Function Block diagram.
6HOHFWLQJ#352),%86#'3
(Select Advanced view level on the Operator Station and view the TEC OPTION function
block).
• Select PROFIBUS DP in the TYPE parameter
• Enter a slave ADDRESS
• Check the FAULT parameter for error messages, rectify if necessary
When setting values for parameters from ConfigEd Lite (or other suitable PC programming tool)
you are able to select any value in the parameter’s range, i.e. -32768 to 32767. If the value is
incorrect, i.e. it doesn’t correspond to a value that can be set using the MMI, then the FAULT
output parameter will be set to PARAMETER.
00,#3DUDPHWHU#'HVFULSWLRQV#IRU#(,#%,6<1&+
TYPE
Range: Enumerated - see below
Selects the type of Technology Option card.
Enumerated Value : Technology Option
3#=#121(
4#=#567;8
5#=#352),%86#'3
6#=#/,1.
7#=#'(9,&(1(7
8#=#&$123(1
9#=#/21:25.6
:#=#7<3(#:
ADDRESS
Range: 0 to 125
The PROFIBUS slave address. Note that addresses 0, 1 and 2 are usually reserved for
PROFIBUS Masters and so should be avoided.
TEC OPTION
FAULT [756]
–
NONE
VERSION [757]
–
0000
OUTPUT 1 [758]
–
0000
OUTPUT 2 [759]
–
0000
NONE – [750] TYPE –
0
–
[751] INPUT 1
–
0
–
[752] INPUT 2
–
0
–
[753] INPUT 3
–
0
–
[754] INPUT 4
–
0
–
[755] INPUT 5
–
Non-specific ConfigEd-Lite view
00,#0HQX#0DS
1RQ0VSHFLILF#00,#YLHZ
4
SETUP PARAMETERS
5
FUNCTION BLOCKS
6
SERIAL LINKS
7
TEC OPTION
TEC OPTION TYPE
TEC OPTION IN 1
TEC OPTION IN 2
TEC OPTION IN 3
TEC OPTION IN 4
TEC OPTION IN 5
TEC OPTION FAULT
TEC OPTION VER
TEC OPTION OUT 1
TEC OPTION OUT 2
TEC OPTION
FAULT [756]
–
NONE
VERSION [757]
–
0101
NETWORK STATE [758]
–
DISABLED
INT DIAGNOSTIC [759]
–
0000
PROFIBUS DP – [750] TYPE –
0
–
[751] ADDRESS
–
0
–
[752] EXT DIAGNOSTIC
–
0
–
[753] INT DIAG SELECT
–
0
–
[754] UNUSED 1
–
0
–
[755] UNUSED 2
–
PROFIBUS DP ConfigEdLite view
00,#0HQX#0DS
352),%86#'3#YLHZ
4
SETUP PARAMETERS
5
FUNCTION BLOCKS
6
SERIAL LINKS
7
TEC OPTION
TYPE
ADDRESS
EXT DIAGNOSTIC
INT DIAG SELECT
UNUSED 1
UNUSED 2
FAULT
VERSION
NETWORK STATE
INT DIAGNOSTIC
SERIAL LINKS is at
Menu Level 1 for the
590+ and 590+DRV.