User`s manual

FX communication
Optional programming port 11
11-1
11
11. Optional Programming Port
This section describes connection to peripheral equipment (programming tool, data access unit
and electronic operation terminal) using the FX
2N
-232-BD, FX
1N
-232-BD, FX
0N
-232ADP, FX
2NC
-
232ADP, FX
1N
-422-BD, or FX
2N
-422-BD as well as cautions on communication. For the operating
procedure of each peripheral equipment and installation of each interface, refer to the
corresponding manual.
11.1 FX
2N
-422-BD, FX
1N
-422-BD
When an FX
2N
-422-BD is installed on the FX
2N
Series, or when an FX
1N
-422-BD is installed on
FX
1N
or FX
1S
Series, the following peripheral equipment (programming tool, data access unit and
electronic operation terminal) can be connected.
However, the FX
2N
-422-BD consumes 5V DC, 60 mA from the FX
2N
programmable controller,
and the FX
1N
-422-BD consumes 5V DC, 60 mA from the FX
1S
or FX
1N
programmable controller.
Make sure that the current consumption of 5V DC for special extensions and peripheral
equipment does not exceed the capacity of the 5V DC power of the FX
2N
, FX
1N
or FX
1S
.
*1: When using other products or cables please check the product manual for required 5V DC
supply.
Note;
These products cannot be connected via FX-2PIF to port of FX
1N
-422-BD or FX
2N
-422-BD. If
connecting, power supply circuit in PLC will go down.
Product Connecting cable Required 5V DC
FX-20P-E
FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP
180mA
FX-10P-E 120mA
Personal computer
(For programming tool)
F
2
-232CAB-1 + FX-232AW(C) + (FX-422CAB0 or
FX-422CAB + FX-20P-CADP) *1
220mA
FX-10DM FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP 220mA
FX-10DU-E FX-20P-CAB0 or FX-20P-CAB + FX-20P-CADP 220mA
FX-20DU-E FX-20DU-CAB0 or FX-20DU-CAB + FX-20P-CADP 180mA
FX-25DU-E, FX-30DU-E,
FX-40DU-ES, FX-40DU-TK-ES,
FX-50DU-TK(S)-E
FX-50DU-CAB0 (-1M, -10M, -20M, -30M, L)
or FX-40DU-CAB (-10M, -20M, -30M) + FX-20P-
CADP
0mA
F940GOT-SWD (LWD)-E,
F930GOT-SBD
FX-50DU-CAB0 (-1M, -10M, -20M, -30M, L) 0mA
F940GOT-SBD (LBD)-H
F9GT-HCAB2-150 + F9GT-HCAB-3M (-10M)
or FX-50DU-CAB0 (-1M) + F9GT-HCNB + F9GT-
HCAB-3M (-10M)
0mA
GOT-A900 (Connecting direct
CPU port type)
F9GT-CAB0 (-150, -10M) 0mA