Ser vice Manual 2008 MITSUBISHI ELECTRIC DLP PROJECTION HDTV V39, V39+, V39++ & V39- CHASSIS WD-52327 WD-52527 V39 Chassis WD-60735 WD-65735 WD-73735 V39+ Chassis WD-65736 WD-73736 V39++ Chassis WD-65835 WD-73835 V39- Chassis WD-60C8 WD-65C8 WD-73C8 Pb Solder CAUTION: Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and "PRODUCT SAFETY NOTICE" contained in this manual.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 CONTENTS INTRODUCTION ................................................................................................................................ 5 Dimensions, weight, power usage, etc. ........................................................................................... 5 PRODUCT SAFETY NOTICE ...........................................................................................
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 USING LEAD FREE SOLDER .......................................................................................................... 33 CHIP PARTS REPLACEMENT ......................................................................................................... 34 REPLACEMENT PARTS ..................................................................................................................
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 INTRODUCTION This service manual provides service instructions for the V39, V39-, V39+ and V39++ chassis types. The specific models for each chassis type, dimensions and weight are listed below. Service personnel should read this manual thoroughly before servicing these chassis.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SAFETY PRECAUTIONS NOTICE: WARNING: 1. 2. Observe all cautions and safety related notes located inside the receiver cabinet and on the receiver chassis. Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard from the receiver's power supplies.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 DISASSEMBLY Back Cover Removal Back Cover Removal Procedure Back Cover Installation 1) Remove the Lamp Cover. 2) Remove screws (A) from the back cover. 3) Pull the back cover from the TV. Reverse the removal procedure but install the Lamp Cover Last. Chassis Removal Chassis Removal 1) Remove four screws (A) 2) Disconnect all cables connecting to the chassis.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Chassis Disassembly Rear Inputs Cover Removal DO NOT use a power driver on this screw. Rear Inputs Cover Removal Procedure 1) Remove 2 nuts (B) from the RF inputs. 2) Remove screws (A) that secure the cover to the chassis. 3) Pull the Inputs Cover from the chassis.. PWB-POWER Removal 1) Remove five screws (B) 2) Disconnect all cables to the PWBPOWER. 3) Release clips (C).
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Chassis Disassembly (continued) Chassis Cover Removal 1) Remove 3 screws (C). 2) Lift the Chassis Cover from the chassis box. PWB-HDMI-FRONT Removal 1) Disconnect all cables to PWBHDMI-FRONT 2) Remove three screws (D). 3) Carefully lift the PWB-HDMIFRONT from the chassis box. 4) To remove PWB-HDMI, remove two screws (E) and slide the PWB out the rear of the shield.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 PWB-MAIN Removal 1) 2) 3) 4) Disconnect all cables to PWB-MAIN Remove two screws (D). Remove screws (E). Carefully lift the PWB-MAIN from the chassis box. PWB-MAIN Installation 1) Install two screws (D) first 2) Then install screws (E). 3) Transfer Index Data from Engine (refer to page 32) 4) Restore Alignment and White Balance Settings. 5) Restore Keystone Geometry from Backup.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 OPTICAL ENGINE REMOVAL OPTICAL ENGINE ASSEMBLY REMOVAL 1) Remove 3 screws (C) from the Optical Engine. 2) Disconnect all cables to the Optical Engine Assembly. 3) Carefully slide the Optical Engine assembly from the cabinet.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 OPTICAL ENGINE REMOVAL FROM THE DUCT ASSEMBLY Upper Duct Assembly Removal Procedure 1) Disconnect the Ballast Fan and Lamp Fan from the back of the Engine (connectors J4 and J8) and loosen wiring harnesses from the looms, refer to page 11 for connector locations. 1) Loosen two screws (a) to remove the Lamp Cartridge, refer to Figure 1.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Figure 4: Lower Duct rear Mounting Screw Figure 5: Lower Duct front Mounting Screw LOWER DUCT REMOVAL 1) Remove the 2 screws (C) one in front and one in the rear of the lower duct, refer to Figures 4 and 5. 2) Carefully remove the lower duct from the Engine. ENGINE REPLACEMENT (Reverse the Removal Procedure) 1) 2) 3) 4) Install Duct assembly on the new Engine.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 BALLAST ASSEMBLY REMOVAL REMOVAL PROCEDURE 1) Remove screw (A) from the Ballast support and screw (B) if the Engine is still mounted in the cabinet. 2) Slide the Ballast Assembly out the rear of the Engine assembly and unplug the Lamp connector (C) at the Ballast. 3) Disconnect connectors CJ1 and CJ3. 4) Remove screw (D) to remove the PWBBALLAST from the Ballast Support.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SCREEN REPLACEMENT (continued) 65 inch Models 73 inch Models Page 15
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SCREEN REPLACEMENT (continued) Screen Assembly Removal (continued) 2) Open the Control Panel door and remove two screws (A). 3) Remove the remaining rear screw in the upper corner and carefully pull the screen assembly from the cabinet. Screen Removal From the BEZEL-FRONT 1) Remove the screws (A) from the top, bottom and side rails.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SCREEN REPLACEMENT (continued) Page 17
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Screen Replacement CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun. This may cause fire and heat related injuries. Lenticular Screen and Fresnel Lens Removal 1) Remove the top, bottom and side HOLDER-SCREEN rails and their cushions from the Bezel.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Speaker Replacement 1) 2) 3) 4) 5) Remove the Bezel screen assembly to access the speakers. Remove 2 screws (A) and carefully slide the Speaker Assembly from the cabinet. Disconnect the leads to the speaker. Remove 4 screws (B) to remove the speaker from the speaker cover. Reverse the procedure to install a replacement speaker.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 OPTION MENU REMOTE CONTROL 1. Press the “MENU” button on the remote hand unit. 2. Press the buttons “2”, “4”, “7” and “0” in order. (The screen will change to the option menu.) V39 OPTION MENU V39+ & V39++ OPTION MENU Digital Signal Strength 1. Tune to a Digital Channel 2. From the Option menu scroll down and highlight Digital Signal Strength 3.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Reset / Initialization SERVICE TIP: Many customer generated symptoms, intermittent symptoms or no symptom found can be resolved by using the various Reset and Initialization options.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 INIT IAL SETTIN GS Audio/Video Settings Video Picture Mode Brilliant Contrast Brilliant Brightness C olor T int Sharpness Brilliant Color Temp.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 INITIAL SETTINGS (continued) Parental Lock Menu U.S. Ratings Lock TV Rating Movie Rating Time Lock by Time Lock Time Unlock Time Off TV-PG PG Off 12:00PM 12:00PM Front Panel Front Button Lock Off 30 TV Volume Format Ant1, 2 (480i) Stretch Ant1, 2 (HD Digital) Standard Input-1, 2, 3 Stretch Comp-1, 2, 3 Standard HDMI-1, 2, 3, 4 (Video or PC) Standard USB Photo Standard A.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 LED Indicator Diagnostics The front panel LEDs provide an indication of the set’s operation, and the possible cause of a malfunction. There are three front panel LEDs, “Power”, “Status” and “Lamp”. The LED display shows the current status or indicates a possible malfunction.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 4. Error Codes The Error Code designations indicating malfunction, or no malfunction, are listed below: ERROR CODES Description Code 12 No Error found 17 Communication loss, TV Micro - Engine (3.3V-ENG-SDA & SC L) Most Likely Cause 18 Engine will not accept data (ASIC-READY signal from Engine is not detected). 32 48 Lamp cover is open. Lamp turns Off while the TV is playing.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Color Wheel Replacement (Part # 938P137010) Symptoms • Noise - Bad Motor Bearing • Solarized Picture - Before replacing the Color Wheel, try adjusting the IDL (Index Delay), refer to page 27 for the alignment procedure. Replacement Procedure CAUTION: This procedure should be done in a dust free environment. Any dust entering into the color wheel chamber can cause abnormalities in the picture.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Replacement Procedure (continued) Handle 6) Remove 3 screws (C) as shown in picture CW3 7) Hold the color wheel by the handle and pull it from the chamber. 8) Install the new color wheel and reverse the above procedure making sure to not scratch the wheel or allow dust inside the chamber CAUTION: Do not twist the ribbon cable to J6 (the shiny silvery contacts must be facing up).
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SERVICE ADJUSTMENTS There are 3 Service Adjustments required in these models: Electrical Adjustments (there are no mechanical adjustments) • • • • • Horizontal Centering Vertical Centering 16 Point Keystone Alignment Letterbox Geometry 4:3 Geometry Measuring Equipment and Jigs • • No additional Test Equipment is required.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 3. Adjustment Function Selection Use the “AUDIO” button to select a specific Adjustment Function. NOTE: There are 2 Service Functions on these models: “TVM” and the “ASIC” function. Service adjustments are performed in the TVM mode. 4. Adjustment Selection Use the “VIDEO” button to select a specific electrical adjustment, “1.HVPOS”. MENU + 2 4 5 7 ISF Function TVM Adjustment 1.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 ® ¦ ¦ ¦ ¦ CURSOR ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ¦ ADUSTMENT POINTS (16 TOTAL) ¦ ¦ 2. Manual Keystone Geometry Alignment (There are 2 modes of adjustment: FULL and TOUCH UP) 1. 2. 3. 4. 5. 6. 7.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 4:3 MODE Select Straightest Blue Lines Figure 2: 4 by 3 Mode Pattern Part 2 (4 by 3 & Letter Box Alignment Mode) 8. Pressing “VIDEO” activates the 4x3 alignment mode, refer to Figure 2. 9. Use the (ff) or (ee) buttons to step through 11 preset 4x3 patterns. Select the pattern with the straightest blue vertical lines that are parallel to the Bezel edge. 10.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 4:3 MODE Select Straightest Red Line (Bottom) Figure 4: Bottom Letter Box Mode Pattern 12. Press “VIDEO” to activate the Bottom Letter Box alignment mode, refer to Figure 4. 13. Use the (ff) or (ee) buttons to step through 10 preset alignment settings. Pick the setting with straightest bottom letter box line that is parallel to the Bezel edge.. 14. Press ‘ENTER” to save and exit the mode.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Pb Solder Using Lead Free Solder The above symbol indicates Lead (Pb) Free solder was used during the construction of PWBs. Only Lead Free solder should be used when servicing these PWBs. Solder must be compatible with that used by the manufacturer. Leaded solder can not be used on PWBs manufactured with Pb-free solder.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 CHIP PARTS REPLACEMENT Some resistors, shorting jumpers (0 Ohm resistors), ceramic capacitors, transistors and diodes are chip parts. The following precautions should be taken when replacing these parts. Cautions: 1. Use a fine tipped, well insulated soldering iron and tweezers. 2.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 REPLACEMENT PARTS Parts Ordering To expedite delivery of replacement parts orders, specify the following: 1. Model Number/Serial Number 2. Part Number and description 3. Quantity Note: Unless complete information is supplied, delay in processing of orders will result.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 QUICK REFERENCE FOR COMMON PARTS ALL MODELS MODEL W D-60735 W D-60C8 W D-65735 W D-65736 W D-65835 W D-65C8 W D-73735 W D-73736 W D-73835 W D-73C8 PART Lamp-Cartridge Lamp Ballast Speaker Fan-Exhaust Fan-Scirocco (Lamp) Fan-Engine (DMD) Sensor-Temperature PWB-Sw-Lamp PART NUMBER 915B403001 938P127010 480P084010 299P335010 299P321010 299P339010 299P337010 935D985001 Module-Color-Wheel 938P13
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 Ref # Part # IC102 IC2001 IC2004 IC2005 IC2101 IC2102 IC2201 IC2202 IC2301 IC2302 IC2401 IC2402 IC2A02 IC2A03 IC2A04 IC2E01 IC2J01 IC3A01 IC3D03 IC3E02 IC3F01 IC3P01 IC7A01 IC7A03 IC7C00 IC7C01 IC7C02 IC7E01 IC7F00 IC7F01 IC7F02 IC7F03 IC7F04
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 Ref # Part # Part Name & Description D7T08 D7T09 D7T10 D7T21 D7T22 D7T23 D7T24 D7T25 D7T26 D7T27 D7T28 D7T29 D7T30 D8203 D8204 D9A00 D9A02 D9A03 D9A04 D9A05 D9A07 D9A08 D9A18 D9A19 D9A20 D9A22 D9A23 D9A24 D9A25 D9A26 D9A31 D9C50 D9C51 D9C52
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 [#] Ref # Part # Part Name & Description L7N01 L8001 L8002 L8003 L8004 L8007 L8008 L8009 L8010 L8011 L8012 L8014 L8015 L8016 L8017 L8018 L8019 L8020 L8021 L8022 L8030 L8202 L8203 L8206 L8302 L8307 L8313 L8318 L8501 L8504 L8511 L9C01 L9C51
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 Ref # Part # Part Name & Description [#] Ref # R9A01 R9A02 R9A03 R9A09 R9A11 R9A19 R9A20 R9A21 R9A22 R9A25 R9A30 R9A42 R9A43 R9A76 R9A77 R9A78 R9A82 R9A83 R9A09 R9A11 R9A19 R9A20 R9A21 R9A22 R9A25 R9A30 R9A42 R9A43 R9A76 R9A77 R9A78 R9A82
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 Ref # Part # [#] Part Name & Description S7L24 S7L25 S7L26 S7L27 S7L28 S7L29 432P109010 432P109010 432P109010 432P109010 432P109010 432P109010 SW-KEY BOARD - KSHS611BT SW-KEY BOARD - KSHS611BT SW-KEY BOARD - KSHS611BT SW-KEY BOARD - KSH
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g), WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 Ref # Part # Part Name & Description 622D484010 HOLDER-LED 623D418010 HOLDER-FAN 623D439020 HOLDER-MIRROR-EDGE 623D439030 HOLDER-MIRROR-EDGE-T 623D439040 HOLDER-MIRROR-EDGE 623D439050 HOLDER-MIRROR-EDGE 642B177010 SUPPORT BALLAST 642C438010
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 [#] Model Legend: (a) WD-60735, (b) WD-60C8, (c) WD-65735, (d) WD-65736, (e) WD-65835, (f) WD-65C8, (g) WD-73735, (h) WD-73736, (i) WD-73835, (j) WD-73C8 SCREEN PARTS Ref# (0) (1) (1) (1) (2) (2) (2) (3) (3) (3) (3) (3) (4) (4) (4) (4) (4) (5) (5) (5) (5) Part# LENS-TAPE 491P217010 491P217020 491P217030 491P218010 491P218020 491P218030 593B261020 593B322010 593B341010 593B350010 593B371010 593B
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 /WD-73735 / WD-73736 / WD-73835 / WD-73C8 MIRROR PARTS LIST Model KIT Description Part # MIRROR WD-60C8 KIT-MIR 767D086010 HOLDER-MIRROR-EDGE (BTM) WD-60735 HOLDER-MIRROR-EDGE (SIDE) 767D086010 623D439050 623D439020 MIRROR WD-65735 WD-65736 KIT-MIR 767D086020 STIFFENER, 22-11/16 in.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 /WD-73735 / WD-73736 / WD-73835 / WD-73C8 (WD-65835 Only) 2-3/8 in. STIFFENER-TOP STIFFENER-SIDE 1-9/16 in. Example of 65” (Back Side of Mirror) Date Code 2 in. COVER-HOLDER-MIRROR 5-7/8 in. (Back Side of Mirror) Example of 73” 5-7/8 in. Date Code 7-7/8 in.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 /WD-73735 / WD-73736 / WD-73835 / WD-73C8 Mirror-3: Install mirror into MIRROR-BOX and secure with HOLDER-MIRROR-SIDE (60” models do not have HOLDER-MIRROR-SIDE) Mirror-4: Install COVER-HOLDER-MIRROR to top of mirror (73” models only) 73” Top of Mirror Front of Mirror Mirror-5: fit COVERHOLDERMIRROR Back of Mirror 73” & V39++ Models: Install HOLDER-MIRROR-TOP.
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 MAIN POWER SUPPLY Page 47
DC/DC Supplies MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Page 48
ANALOG VIDEO SIGNAL PATH MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Page 49
DIGITAL VIDEO SIGNAL PATH MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Page 50
SOUND SIGNAL PATH MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Page 51
OVERALL CONTROL CIRCUIT MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Page 52
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 INPUT/OUTPUT AUTO DETECT Page 53
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 Lamp Control CIRCUITRY Circuitry LAMP CONTROL Page 54
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 SHORT DETECT CIRCUITRY ENGINE PROTECT CIRCUITRY Page 55
MODELS: WD-60735 / WD-60C8 / WD-65735 / WD-65736 / WD-65835 / WD-65C8 / WD-73735 / WD-73736 / WD-73835 / WD-73C8 System 5 / Wired Remote I/O Page 56
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 V39 & V39+ only PG 1.....BLOCK 6 5 4 3 2 1 HD1 G FI-RE21S-HF 22 GND 23 GND 24 GND 25 GND 5 4 3 2 1 PA 3. TP13.etc. show test points. 4. CAPACITOR HD2 Not indicated PF, for numbers more than 1 uF, for numbers less than 1 Value CABLE-3D 7 2. Wave form were taken with standard color bar signal.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PG 2.....POWER A (TO LAMP BALLAST) PL 5 1 LAMP GND 340V 3 4 B 1 L9D03 ! HF2836-353Y1R0-T01 (MI) 3 D9A18 1S2076A/1S2471OM LAMP BALLAST POWER SUPPLY. DOUBLER CIRCUIT. 2 ! S2 2 3 1 4 LAMP BALLAST SWITCH C1 Q9A09 C2 S1 LKT1AF-12V (MI) K9A20 3 S2 2 R9A43 220K 1/2W R9A42 220K 1/2W S1 R9A02 1.8 10W 2SC3052-T112-1E,F R9A41 3.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 3.....MAIN1 [DC-DC / IF] TO PWB-PREAMP/CONT/LED 12VSL TO 5VSL B 3 BAT54S D9G01 D9G02 1 2 R9G03 100 1/16W 1 C9G03 0.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 4.....MAIN2 [AV-SWITCH / TUNER] A TO FRONT PWB 12 11 10 8 9 7 6 CE 5 4 3 2 1 DGND Fr_Y/CV R2J22 75 1/16W R2J24 75 1/16W R2J26 120K 1/16W Fr_PB Fr_PR Fr_R R2J28 120K 1/16W Fr_L Fr_YUV_Det Fr_CV_DET BOSS R2J20 75 1/16W B MAIN 03 IR-OUT INP2-Y 2 3 R2J93 120K 1/16W R1 Q2J05 13 6 14 6 PB1 R2J65 C2J06 1U 10V/6.
R2201 150 1/10W T.M.D.S. Data 0- 10 T.M.D.S. Clock+ 11 T.M.D.S. Clock Shield R2207 47K 1/16W 3 12VSL-SBL BLUE-LED HDMI-DETF 4 SYST5-CTRL2 R2E05 22 1/10W 10 3B 2B 5 9 3A 2Y 6 3Y VSS 8 R2E06 22 1/10W R2EA3 22K 1/16W DGND 7 R2016 3.3K R2015 1/16W 3.
3 4 5 6 7 8 10 11 12 R8097 100 1/16W 8 2 7 3 6 4 5 DGND FCEN[3] no use A3 A4 A5 A6 A7 X240-YIN D-IF+ X240-CIN D-IF- IF-AGC 3.3VS MAIN 9 OSDSEL1 IF+ IF- IF-AGC FDC_AVSS FDC_AVDD FE_OSC_AVDD FS_AVSS FS_AVDD FS_DVSS FS_DVDD FPVDD FPVSS TP-GP4 5VS R8053 100 1/16W 1/16W R8057 10K 1/16W A8 A9 A10 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 25V/16V 25V/16V A24 6 7 3.3V DGND IC8002 R8066 3.3K 1/16W C80K5 10uF 6.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 7.....MAIN5 [DM-MEMORY] A MEMVREF R8111 1K 1/16W R8110 1K 1/16W DGND MEMCLKA,MEMCLKAN,MEMCLKEA CASAN,CSAN[0],DQMAN[0-3],QSA[0-3],RASAN,WEAN CASAN,CSAN[0],DQMAN[0-3],QSA[0-3],RASAN,WEAN AA[0-14] AA[0-14] DQA[0-31] B DQA[0-31] TP1.3VS-DM R8102 R8118 1/16W 33-JX4 RM1608X4 (3216) 1/16W 33-JX4 RM1608X4 (3216) R8126 33 1/16W 1.3V DQA[3] C8104 0.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MS-SI MS-CLK LAD[15] IC8322 KFG1216U2B-DIB60 MS-SO A MS-CSN PG 8.....MAIN6 [DM-ROM / AV] G10 H10 J10 K10 MS-CSN A10 B10 C10 D10 E10 F10 L10 M10 N10 MS-SO MS-SI DGND A1 A2 A3 A4 A5 A6 C8310 0.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 9.....MAIN7 [ANALOG-DIGITAL CONVERTOR] A B TP1.8V-ADC [ 1.8V C7E17 0.1 25V/16V C7E18 47 6.3V 3.3VSCL 3.3VSDA DGND ] C TO MAIN 013 (MICRO) L7E03 1.8V GND [ C7E37 8200 C7E33 25V/16V 0.1 R7EA5 0 1/16W R7E71 0 1/16W L7E01 DGND 3.3V 1.8V 1.8V-HDMI D3.3V R7E37 1.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 10....
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 11....MAIN9 [SPA3 MEMORY] [ SPA2-2.5VS TPVTTREF SPASDVREF S2D[0-15] C7F02 0.1 25V/16V VSS 66 DQ0 DQ15 65 3 VDDQ 3 6 4 DQ1 4 5 5 DQ2 6 VSSQ 2 7 9 VDDQ VSSQ 58 2 7 3 6 10 DQ5 DQ10 57 3 6 4 5 11 DQ6 4 5 UDQS 51 R7F05 56 8 26 BA0 A11 41 2 7 2 7 27 BA1 A9 40 3 6 3 6 28 A10/AP A8 39 4 5 4 5 29 A0 A7 38 30 A1 31 A2 32 C7F10 0.1 25V/16V 7 SAD[3] SAD[2] SAD[1] C7F09 0.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 12....MAIN10 [TMDS] A OUTBB[1] C7C77 0.1 25V/16V OUTRB[4] OUTRB[5] OUTRB[6] 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 C7C95 0.
MAIN 5 9 10 11 12 13 14 15 16 I2SMCLKA I2SSDATA I2SLRCKA I2SSCLKA MASD MAWS A 8 I2S_A MAIN 4 MAIN 4 MASCK 3.3VS PWR MAIN 1 7 AUDADCLK PG 13....MAIN11 [AUDIO] 6 Sys.clk. gen. 5 MAIN 4 4 1.8VS-DM 3 9VS 2 5VS 1 9VS C3A01 MAIN-R Q3A01 R3A06 100 AUDIO ADC Q3A02 DGND 2SC3052-T112-1E,F L3A02 2SC3052-T112-1E,F ADC3.3VS 1/16W MAIN-L 12.288MHz MAIN 2 0.1 25V/16V MMZ1608S601A L3A03 R3A01 100 5VS-A MMZ1608S601A 1/16W R3A07 820 1/16W C3A05 K-4.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 14....MAIN12 [MICRO] 3.3VSL A LAMP-R R7AC2 4.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PG 15....
