User manual

2
2
4
7
I
285
Upper limit signal (X1E) . . . . . . . . . . . . . . . . . . . . . 34
Upper limit switch (FLS)/lower limit switch (RLS) . . 215
V
Variable parameter . . . . . . . . . . . . . . . . . . . . . . . . 75
Voltage range/Current consumption . . . . . . . . . . . . 40
W
WDT error, H/W error signal (X10) . . . . . . . . . . . . . 32
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
When a positioning error occurs . . . . . . . . . . . . . . 247
When mounted on MELSECNET/H remote I/O station
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
When operation stops abnormally during positioning
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
When OPR cannot be completed . . . . . . . . . . . . . 249
When positioning cannot be executed . . . . . . . . . . 246
When the motor does not stop . . . . . . . . . . . . . . . 246
When the OP position is in error . . . . . . . . . . . . . . 249
When the positioning speed is different from the specified
speed
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
When the upper limit switch (FLS)/lower limit switch
(RLS) function is not used
. . . . . . . . . . . . . . . . . . 216
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Wiring upper limit switch (FLS) and lower limit switch
(RLS)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
Workpiece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Z
Zero adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 59
ZERO LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Zero signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279
Zero/gain adjustment. . . . . . . . . . . . . . . . . . . . . . . 59
Zero/gain adjustment change complete flag (X2B) . . 36
Zero/gain adjustment change request signal (Y1B) . . 37
Zero/gain adjustment data writing complete flag (X2A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Zero/gain adjustment data writing request signal (Y1A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Zero/gain adjustment mode/Normal mode setting . . 101
Zero/gain adjustment specification . . . . . . . . . . . . . 92
Zero/gain adjustment status . . . . . . . . . . . . . . . . . . 86
Zero/gain adjustment value specification . . . . . . . . . 92
Zero/gain execution status . . . . . . . . . . . . . . . . . . . 86