OPERATION MANUAL FX-10P-E
This manual explains the programming and monitoring procedures of the micro PC MELSEC-FX series using the FX-10P-E handy programming panel. Read this manual carefully and thoroughly and make sure the specifications for handy programming panel are correct. See the corresponding FX series PC manual for details about PC handing and instructions. CONTENTS 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P1 2. Sample program operation . . . . . . . . . . . . . . . . . . P11 3.
FX-10P-E Handy programming panel Guidelines for the Safety of the User and Protection of the FX-10P-E HANDY PROGRAMMING PANEL. This manual provides information for the use of the FX-10P-E HANDY PROGRAMMING PANEL. The manual has been written to be used by trained and competent personnel.
FX-10P-E Handy programming panel Note’s on the Symbols Used in this Manual At various times through out this manual certain symbols will be used to highlight points which are intended to ensure the users personal safety and protect the integrity of equipment. Whenever any of the following symbols are encountered its associated note must be read and understood. Each of the symbols used will now be listed with a brief description of its meaning.
FX-10P-E Handy programming panel • Under no circumstances will Mitsubishi Electric be liable responsible for any consequential damage that may arise as a result of the installation or use of this equipment. • All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.
FX-10P-E Handy programming panel Caution on operation Thoroughly read the manual and sufficiently assure safety before executing the operation to forcibly set devices to ON/OFF or the operation to change present values and set values of word devices in the test mode. Otherwise, the machine may be damaged and accidents may occur by erroneous operations.
Version upgrade to support FX1S, FX1N, FX2N and FX2NC Series Programmable controllers. (ver 4.10 or later) The FX-10P-E (ver 4.10 or later) fully supports all items and procedures used for the FX1S, FX1N, FX2N and FX2NC PLCs. Read section 1-3 in addition to the contents of the text when using the FX-10P-E (ver 4.10 or later). 1. New Features Table 1.
2. List of Additional Devices and Instructions • For details of each instruction and devices, refer to the FX programming manual. Table 2.1 Auxiliary relays Data registers Index registers Table 2.2 Devices M0 to M3071 D0 to D7999 V0 to V7, Z0 to Z7 3072 points 8000 points 16 points Basic Instructions LDP ORP LDF ORF ANDP INV ANDF Table 2.3 Applied Instructions FNC No. Instruction 59 PLSR 110 ECMP 111 EZCP 118 EBCD 119 EBIN 120 EADD 121 ESUB 122 EMUL 123 EDIV Applied Instructions FNC No.
3. New Operations for FX2N, FX2NC, FX1N, FX1S Support 3.1 Basic and Applied instructions are added Symbol and input operation of additional basic instructions Table 3.
Applied instruction input operation FNC Applied Instruction No. SP Operand 1 SP Operand 2 ..... GO The number of operands vary depending on the instruction. • It is the responsibility of the operator to ensure that the instruction entered is valid for the current unit.
3.2 Expansion of Device Range • For a list of the new device ranges see section 2. Handling index registers “V0” and “Z0” index registers are equivalent to registers “V” and “Z” respectively, so either one can be used for programming. When entering “V1” to “V7” or “Z1” to “Z7” add a numeral 1 to 7 to the “V” or “Z” before pressing 3.3 SP or GO .
3.4 Others Device conversion Device number conversion is not possible between the following devices because the number of program steps required is different. - M0 to M1535 ↔ M1536 to M3071 (FX2N and FX2NC only) - 16-bit counter ↔ 32-bit counter (all FX models) Writing the program to the FX-EEPROM-16 • When an instruction is inserted to a 16K-step program saved in the FX-EEPROM-16 in online mode, it may take 5 to 50 seconds depending on the total program size and the instruction insertion position.
OPERATION MANUAL FX-10P-E HEAD OFFICE: MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310 HIMEJI WORKS: 840, CHIYODA CHO, HIMEJI, JAPAN MODEL FX-10P-O-E MODEL CODE 09R913 JY992D33401B (SEN) Effective Mar. 2003 Specifications are subject to change without notice.
