Car Amplifier User Manual

ManualsBrandsMitsubishi Electronics ManualsCar AmplifierMELSERVO MR-J2S- A

Table Of Contents

Safety Instructions
COMPLIANCE WITH EC DIRECTIVES
CONFORMANCE WITH UL/C-UL STANDARD
<>
CONTENTS
Optional Servo Motor Instruction Manual CONTENTS
1. FUNCTIONS AND CONFIGURATION
- 1.1 Introduction
- 1.2 Function block diagram
- 1.3 Servo amplifier standard specifications
- 1.4 Function list
- 1.5 Model code definition
- 1.6 Combination with servo motor
- 1.7 Structure
  - 1.7.1 Parts identification
  - 1.7.2 Removal and reinstallation of the front cover
- 1.8 Servo system with auxiliary equipment
2. INSTALLATION
- 2.1 Environmental conditions
- 2.2 Installation direction and clearances
- 2.3 Keep out foreign materials
- 2.4 Cable stress
3. SIGNALS AND WIRING
- 3.1 Standard connection example
- 3.2 Internal connection diagram of servo amplifier
- 3.3 I/O signals
  - 3.3.1 Connectors and signal arrangements
  - 3.3.2 Signal explanations
- 3.4 Detailed description of the signals
- 3.5 Alarm occurrence timing chart
- 3.6 Interfaces
  - 3.6.1 Common line
  - 3.6.2 Detailed description of the interfaces
- 3.7 Input power supply circuit
- 3.8 Connection of servo amplifier and servo motor
- 3.9 Servo motor with electromagnetic brake
- 3.10 Grounding
- 3.11 Servo amplifier terminal block (TE2) wiring method
  - 3.11.1 For the servo amplifier produced later than Jan. 2006
  - 3.11.2 For the servo amplifier produced earlier than Dec. 2005
- 3.12 Instructions for the 3M connector
- 3.13 Power line circuit of the MR-J2S-11KA to MR-J2S-22KA
4. OPERATION
- 4.1 When switching power on for the first time
- 4.2 Startup
- 4.3 Multidrop communication
5. PARAMETERS
- 5.1 Parameter list
  - 5.1.1 Parameter write inhibit
  - 5.1.2 Lists
- 5.2 Detailed description
6. DISPLAY AND OPERATION
- 6.1 Display flowchart
- 6.2 Status display
- 6.3 Diagnostic mode
- 6.4 Alarm mode
- 6.5 Parameter mode
- 6.6 External I/O signal display
- 6.7 Output signal (DO) forced output
- 6.8 Test operation mode
7. GENERAL GAIN ADJUSTMENT
- 7.1 Different adjustment methods
  - 7.1.1 Adjustment on a single servo amplifier
  - 7.1.2 Adjustment using MR Configurator (servo configuration software)
- 7.2 Auto tuning
- 7.3 Manual mode 1 (simple manual adjustment)
  - 7.3.1 Operation of manual mode 1
  - 7.3.2 Adjustment by manual mode 1
- 7.4 Interpolation mode
- 7.5 Differences in auto tuning between MELSERVO-J2 and MELSERVO-J2-Super
  - 7.5.1 Response level setting
  - 7.5.2 Auto tuning selection
8. SPECIAL ADJUSTMENT FUNCTIONS
- 8.1 Function block diagram
- 8.2 Machine resonance suppression filter
- 8.3 Adaptive vibration suppression control
- 8.4 Low-pass filter
- 8.5 Gain changing function
9. INSPECTION
10. TROUBLESHOOTING
- 10.1 Trouble at start-up
- 10.2 When alarm or warning has occurred
11. OUTLINE DIMENSION DRAWINGS
- 11.1 Servo amplifiers
- 11.2 Connectors
12. CHARACTERISTICS
- 12.1 Overload protection characteristics
- 12.2 Power supply equipment capacity and generated loss
- 12.3 Dynamic brake characteristics
- 12.4 Encoder cable flexing life
- 12.5 Inrush currents at power-on of main circuit and control circuit
13. OPTIONS AND AUXILIARY EQUIPMENT
- 13.1 Options
- 13.2 Auxiliary equipment
14. COMMUNICATION FUNCTIONS
- 14.1 Configuration
  - 14.1.1 RS-422 configuration
  - 14.1.2 RS-232C configuration
- 14.2 Communication specifications
  - 14.2.1 Communication overview
  - 14.2.2 Parameter setting
- 14.3 Protocol
- 14.4 Character codes
- 14.5 Error codes
- 14.6 Checksum
- 14.7 Time-out operation
- 14.8 Retry operation
- 14.9 Initialization
- 14.10 Communication procedure example
- 14.11 Command and data No. list
  - 14.11.1 Read commands
  - 14.11.2 Write commands
- 14.12 Detailed explanations of commands
15. ABSOLUTE POSITION DETECTION SYSTEM
- 15.1 Outline
  - 15.1.1 Features
  - 15.1.2 Restrictions
- 15.2 Specifications
- 15.3 Battery installation procedure
- 15.4 Standard connection diagram
- 15.5 Signal explanation
- 15.6 Startup procedure
- 15.7 Absolute position data transfer protocol
- 15.8 Examples of use
- 15.9 Confirmation of absolute position detection data
- 15.10 Absolute position data transfer errors
  - 15.10.1 Corrective actions
  - 15.10.2 Error resetting conditions
Appendix
- App 1. Signal arrangement recording sheets
- App 2. Status display block diagram
- App 3. Combination of servo amplifier and servo motor
REVISIONS

3 - 36

3. SIGNALS AND WIRING

3.4.5 Speed/torque control change mode

Set "0003" in parameter No. 0 to switch to the speed/torque control change mode.

(1) Control change (LOP)

Use control change (LOP) to switch between the speed control mode and the torque control mode from

an external contact. Relationships between LOP and control modes are indicated below:

(Note) LOP Servo control mode

0 Speed control mode

1 Torque control mode

Note. 0: off

1: on

The control mode may be changed at any time. A change timing chart is shown below:

Note: When the start (ST1 ST2) is switched off as soon as the mode is changed to speed control,

the servo motor comes to a stop according to the deceleration time constant.

10V

OFF

Torque

control mode

Servo motor speed

Control change (LOP)

(Note)

Speed

control mode

Speed

control mode

Analog torque

command (TC)

Load torque

Forward rotation in driving mode

(2) Speed setting in speed control mode

As in Section 3.4.2 (1).

(3) Torque limit in speed control mode

As in Section 3.4.1 (5).