Car Amplifier User Manual

ManualsBrandsMitsubishi Electronics ManualsCar AmplifierMELSERVO MR-J2S- A

171

172

173

174

175

176

177

178

179

180

Table Of Contents

Safety Instructions
COMPLIANCE WITH EC DIRECTIVES
CONFORMANCE WITH UL/C-UL STANDARD
<>
CONTENTS
Optional Servo Motor Instruction Manual CONTENTS
1. FUNCTIONS AND CONFIGURATION
- 1.1 Introduction
- 1.2 Function block diagram
- 1.3 Servo amplifier standard specifications
- 1.4 Function list
- 1.5 Model code definition
- 1.6 Combination with servo motor
- 1.7 Structure
  - 1.7.1 Parts identification
  - 1.7.2 Removal and reinstallation of the front cover
- 1.8 Servo system with auxiliary equipment
2. INSTALLATION
- 2.1 Environmental conditions
- 2.2 Installation direction and clearances
- 2.3 Keep out foreign materials
- 2.4 Cable stress
3. SIGNALS AND WIRING
- 3.1 Standard connection example
- 3.2 Internal connection diagram of servo amplifier
- 3.3 I/O signals
  - 3.3.1 Connectors and signal arrangements
  - 3.3.2 Signal explanations
- 3.4 Detailed description of the signals
- 3.5 Alarm occurrence timing chart
- 3.6 Interfaces
  - 3.6.1 Common line
  - 3.6.2 Detailed description of the interfaces
- 3.7 Input power supply circuit
- 3.8 Connection of servo amplifier and servo motor
- 3.9 Servo motor with electromagnetic brake
- 3.10 Grounding
- 3.11 Servo amplifier terminal block (TE2) wiring method
  - 3.11.1 For the servo amplifier produced later than Jan. 2006
  - 3.11.2 For the servo amplifier produced earlier than Dec. 2005
- 3.12 Instructions for the 3M connector
- 3.13 Power line circuit of the MR-J2S-11KA to MR-J2S-22KA
4. OPERATION
- 4.1 When switching power on for the first time
- 4.2 Startup
- 4.3 Multidrop communication
5. PARAMETERS
- 5.1 Parameter list
  - 5.1.1 Parameter write inhibit
  - 5.1.2 Lists
- 5.2 Detailed description
6. DISPLAY AND OPERATION
- 6.1 Display flowchart
- 6.2 Status display
- 6.3 Diagnostic mode
- 6.4 Alarm mode
- 6.5 Parameter mode
- 6.6 External I/O signal display
- 6.7 Output signal (DO) forced output
- 6.8 Test operation mode
7. GENERAL GAIN ADJUSTMENT
- 7.1 Different adjustment methods
  - 7.1.1 Adjustment on a single servo amplifier
  - 7.1.2 Adjustment using MR Configurator (servo configuration software)
- 7.2 Auto tuning
- 7.3 Manual mode 1 (simple manual adjustment)
  - 7.3.1 Operation of manual mode 1
  - 7.3.2 Adjustment by manual mode 1
- 7.4 Interpolation mode
- 7.5 Differences in auto tuning between MELSERVO-J2 and MELSERVO-J2-Super
  - 7.5.1 Response level setting
  - 7.5.2 Auto tuning selection
8. SPECIAL ADJUSTMENT FUNCTIONS
- 8.1 Function block diagram
- 8.2 Machine resonance suppression filter
- 8.3 Adaptive vibration suppression control
- 8.4 Low-pass filter
- 8.5 Gain changing function
9. INSPECTION
10. TROUBLESHOOTING
- 10.1 Trouble at start-up
- 10.2 When alarm or warning has occurred
11. OUTLINE DIMENSION DRAWINGS
- 11.1 Servo amplifiers
- 11.2 Connectors
12. CHARACTERISTICS
- 12.1 Overload protection characteristics
- 12.2 Power supply equipment capacity and generated loss
- 12.3 Dynamic brake characteristics
- 12.4 Encoder cable flexing life
- 12.5 Inrush currents at power-on of main circuit and control circuit
13. OPTIONS AND AUXILIARY EQUIPMENT
- 13.1 Options
- 13.2 Auxiliary equipment
14. COMMUNICATION FUNCTIONS
- 14.1 Configuration
  - 14.1.1 RS-422 configuration
  - 14.1.2 RS-232C configuration
- 14.2 Communication specifications
  - 14.2.1 Communication overview
  - 14.2.2 Parameter setting
- 14.3 Protocol
- 14.4 Character codes
- 14.5 Error codes
- 14.6 Checksum
- 14.7 Time-out operation
- 14.8 Retry operation
- 14.9 Initialization
- 14.10 Communication procedure example
- 14.11 Command and data No. list
  - 14.11.1 Read commands
  - 14.11.2 Write commands
- 14.12 Detailed explanations of commands
15. ABSOLUTE POSITION DETECTION SYSTEM
- 15.1 Outline
  - 15.1.1 Features
  - 15.1.2 Restrictions
- 15.2 Specifications
- 15.3 Battery installation procedure
- 15.4 Standard connection diagram
- 15.5 Signal explanation
- 15.6 Startup procedure
- 15.7 Absolute position data transfer protocol
- 15.8 Examples of use
- 15.9 Confirmation of absolute position detection data
- 15.10 Absolute position data transfer errors
  - 15.10.1 Corrective actions
  - 15.10.2 Error resetting conditions
Appendix
- App 1. Signal arrangement recording sheets
- App 2. Status display block diagram
- App 3. Combination of servo amplifier and servo motor
REVISIONS

7 - 6

7. GENERAL GAIN ADJUSTMENT

7.2.4 Response level setting in auto tuning mode

Set the response (The first digit of parameter No.2) of the whole servo system. As the response level

setting is increased, the trackability and settling time for a command decreases, but a too high response

level will generate vibration. Hence, make setting until desired response is obtained within the vibration-

free range.

If the response level setting cannot be increased up to the desired response because of machine resonance

beyond 100Hz, adaptive vibration suppression control (parameter No. 60) or machine resonance

suppression filter (parameter No. 58

59) may be used to suppress machine resonance. Suppressing

machine resonance may allow the response level setting to increase. Refer to Section 8.1 for adaptive

vibration suppression control and machine resonance suppression filter.

Parameter No. 2

Response level setting

Gain adjustment mode selection

Machine characteristic

Response level setting

Machine rigidity

Machine resonance

frequency guideline

Guideline of corresponding machine

1 Low 15Hz

2 20Hz

3 25Hz

4 30Hz

5 35Hz

6 45Hz

7 55Hz

8 Middle 70Hz

9 85Hz

A 105Hz

B 130Hz

C 160Hz

D 200Hz

E 240Hz

F High 300Hz

Large conveyor

Arm robot

General machine

tool conveyor

Precision

working

machine

Inserter

Mounter

Bonder