INSTALLATION GUIDE 1
Setting information MAC-558IF-E address(MAC) MAC-558IF-E serial number(ID) MAC-558IF-E code(PIN) Indoor unit model name Indoor unit serial number Outdoor unit model name Outdoor unit serial number System commissioning date MAC-558IF-E installation date Installer contact details Name Telephone number Wi-Fi Control minimum requirements for operation: • Compatible WPS router, capable of WPA2-AES encryption.
Mitsubishi Electric Wi-Fi Heat Pump Control Important Note: Before carrying out installation of the MAC-558IF-E adaptor please read the safety instructions listed on page 8 of this installation guide. Register Your Heat Pump(s) Thank you for choosing a Mitsubishi Electric Heat Pump with Wi-Fi Control. Once your adaptor is installed either download the app (search term: Mitsubishi Electric) or visit our website to register your heat pump(s).
Wi-Fi Control: Installation Instructions Information for installers The following steps explain how to connect the MAC-558IF-E Adaptor to a Mitsubishi Electric Heat Pump. EQUIPMENT REQUIRED FOR INSTALL: MAC-558IF-E Adaptor WPS Enabled Router Wi-Fi Installation Guide Tools to remove cover of indoor unit INSTALLATION GUIDE # 2 Ph ill ip s Important Note: Before going to the users home, ensure they have a WPS capable router and WPA2-AES encryption can be set.
3 Remove the cover of the indoor unit, the cable terminal, and the cover to the control board. 5 Run the cables down the back of the unit with the other cables. Tuck cabling away and secure. 7 Check that the MAC-558IF-E Adaptor is flashing. The install has now been completed. 4 Locate the CN105 port on the main control board and connect the MAC-558IF-E Adaptor. 6 Reassemble the indoor unit and restore power to the system. 8 The adaptor is now able to be connected to the user’s router.
Wi-Fi Control: Installation Instructions Information for users The following steps explain how to connect the MAC-558IF-E Adaptor to a router. KEY (LED LIGHTS): ON OFF FLASHING 1 Check Wi-Fi and WPS are enabled on your router. The connection procedure varies depending on your router – refer to your router manual for more information. 3 Activate WPS on your adaptor by using a small object to press and hold the WPS button for two seconds. 6 2 Activate WPS mode on your router.
4 Turn the adaptor over and check LED 1 (top light) is flashing. 6 Next, the bottom light (LED 3) will start flashing as it connects to the internet. This may continue for up to 10 minutes. 8 If LED 2 (orange) lights up at any stage there may be a problem. Check the troubleshooting section on page 11.* 5 When LED 1 remains solid for 5 seconds the adaptor is connecting to your router. 7 When LED 1 and LED 3 flash alternately the unit is successfully connected to the internet.
Safety Instructions • Read all safety instructions before using the Wi-Fi Adaptor. • This installation manual contains important safety information. Be sure to comply with the instructions. • After installing the Wi-Fi Adaptor, provide this installation manual to the user. Instruct users to store it with their heat pump instruction manual in a safe location. Warning (Improper handling may have serious consequences, including serious injury or death.
Caution (Improper handling may have consequences, including injury or damage to house.) • To prevent damage from static electricity, touch a nearby metal body to discharge static electricity from yourself before touching the Wi-Fi Adaptor. • Do not use in special environments.
Product Introduction No Item Description 1 WPS switch Activates WPS 2 RESET switch Resets the system and ALL settings 3 LED1 (Green) Shows the wireless communication state 4 LED2 (Orange) Shows the MAC-558IF-E state 5 LED3 (Green) 3 4 5 1 2 Shows the local communication state Parts Adaptor unit [with connecting cable (5-core)] Optional screw for mounting 3.
Troubleshooting If at any stage you see the orange LED 2 light up, this is an indication that there is a problem with the router communicating with the adaptor. If this occurs, you may need to check the following: • WPS is working on your router • Signal is reaching the adaptor • DHCP addresses are available • Your router is compatible with the adaptor.
Contact Details Mitsubishi Electric New Zealand Mitsubishi Electric Australia www.mitsubishi-electric.co.nz/wifi www.mitsubishielectric.com.au/wifi WELLINGTON SYDNEY HEAD OFFICE HEAD OFFICE 1 Parliament Street PO Box 30772 Lower Hutt 5040 348 Victoria Road Rydalmere NSW 2116 Phone 0800 639 434 Fax (04) 560 9133 Phone (02) 9684 7777 Fax (02) 9898 0484 Helpline opening hours 8.30am - 5.
