KD79D904H01_Cover.fm Page 1 Friday, October 14, 2011 9:58 AM Air-Conditioners PEAD-RP71, 100, 125, 140JAA OPERATION MANUAL FOR USER For safe and correct use, please read this operation manual thoroughly before operating the air-conditioner unit.
Contents 1. Safety Precautions ................................................................ 2 2. Parts Names ......................................................................... 3 3. Screen Configuration ............................................................ 6 4. Setting the Day of the Week and Time .................................. 6 5. Operation .............................................................................. 6 6. Timer ........................................................
1. Safety Precautions 1.2. During operation Caution: Caution: • • • • • Do not use any sharp object to push the buttons, as this may damage the remote controller. Do not twist or tug on the remote controller cord as this may damage the remote controller and cause malfunction. Never remove the upper case of the remote controller. It is dangerous to remove the upper case of the remote controller and touch the printed circuit boards inside. Doing so can result in fire and failure.
2. Parts Names ■ Wired Remote-Controller (PAR-21MAA option) “Sensor” indication Display Section Displayed when the remote controller sensor is used. Day-of-Week For purposes of this explanation, all parts of the display are shown as lit. During actual operation, only the relevant items will be lit. Shows the current day of the week. Time/Timer Display “Locked” indicator Shows the current time, unless the simple or Auto Off timer is set. If the simple or Auto Off timer is set, shows the time remaining.
2. Parts Names ■ Wireless Remote-Controller (option) SET TEMPERATURE button ON/OFF button SET TEMPERATURE button sets and any desired room temperature. CHECK TEST RUN MODEL SELECT Pushing button starts operation. Pushing again stops operation. NOT AVAILABLE FAN SPEED button This button is used to set fan speed to low, medium or high. AUTO STOP/AUTO START button Used for selecting timed starting or stopping.
3. Screen Configuration Set Day/Time Function Selection of remote controller TIME SUN A D C Standard Control Screens ˚F˚C ˚C OFF ON B C Timer Monitor Timer Setup SUN MON TUE WED THU FRI SAT MON TIMER OFF B ˚F˚C WEEKLY WEEKLY For details on setting the language for the remote controller display, refer to section 8. Function Selection. The initial language setting is English.
5. Operation ■ Press the ON/OFF button 1 again. • The ON lamp 1 and the display area go dark. Note: Even if you press the ON/OFF button immediately after shutting down the operation is progress, the air conditioner will not start for about three minutes. This is to prevent the internal components from being damaged. 5.2. Mode select ■ Press the operation mode ( tion mode 2. 5.3. Temperature setting s To decrease the room temperature: Press button 3 to set the desired temperature.
5. Operation 5.5.1. For Wired Remote-controller ● To run the ventilator together with the indoor unit: ■ Press the ON/OFF button 1. • The Vent indication appears on the screen (at 8). The ventilator will now automatically operate whenever the indoor unit is running. ● To run the ventilator independently: ■ Press the Mode button 2 until cause the ventilator to start. appears on the display. This will ● To change the ventilator force: ■ Press the Ventilation button 8 as necessary.
6. Timer 7. Press the appropriate Set Temperature button 3 to set the desired temperature (at 7). * Each press changes the setting, in the following sequence: No display (no setting) ⇔ 24 ⇔ 25 ⇔ ... ⇔ 29 ⇔ 30 ⇔ 12 ⇔ ... ⇔ 23 ⇔ No display. (Available range: The range for the setting is 12 °C to 30 °C. The actual range over which the temperature can be controlled, however, will vary according to the type of the connected unit.) 8.
6. Timer 7. After completing steps 3 to 6 above, press the Filter in the value. button 4 to lock Note: Your new settings will be cancelled if you press the Mode (Return) button 2 before pressing the Filter button 4.
6. Timer 6.2. For wireless remote controller (option) 4 5 Timer Setting TIMER AFTER OFF AUTO OFF C D B A 1 1. Be sure that the “Auto Off” is visible on the screen (at 1). 2. Hold down the Timer Menu button B for 3 seconds, so that “Monitor” is indicated on the screen (at 4). • The timer remaining to shutdown appears at 5. 3. To close the monitor and return to the standard control screen, press the Mode (Return) button 2.
7. Other Functions 7.2. Error Codes indication When the Check button is pressed: If you have entered contact number to be called in the event of a problem, the screen displays this number. (You can set this up under Function Selection of remote controller. For information, refer to section 8.) CALL:XXXX XXX:XXX ERROR CODE ˚C ˚C ON/OFF ON/OFF Error Code ERROR CODE ON/OFF ON lamp (Flashing) Indoor Unit’s Error Code Indoor Unit No.
8. Function Selection [Function selection flowchart] Setting language (English) Normal display (Display when the air condition is not running) Hold down the E button and press the D button for 2 seconds. E Press the operation mode button. G Press the TIMER MENU button. D Press the TIMER ON/OFF button. Hold down the E button and press the D button for 2 seconds. Remote controller function selection mode Item1 G Change Language Item2 Dot display English G Germany E F Spanish TEMP.
8. Function Selection [Detailed setting] [4]–3. Mode selection setting [4]–1. CHANGE LANGUAGE setting The language that appears on the dot display can be selected. • Press the [[ MENU] button G to change the language. 1 English (GB), 2 German (D), 3 Spanish (E), 4 Russian (RU), 5 Italian (I), 6 Chinese (CH), 7 French (F), 8 Japanese (JP) Refer to the dot display table. [4]–2. Function limit (1) Operation function limit setting (operation lock) • To switch the setting, press the [ ON/OFF] button D.
8.
8. Function Selection Selecting language English Germany Spanish Russian Italy Chinese French Japanese Room air temperature display setting Automatic cooling/heating display setting 9.
11. Trouble Shooting Having trouble? Air conditioner does not heat or cool well. Here is the solution. (Unit is operating normally.) ■ Clean the filter. (Airflow is reduced when the filter is dirty or clogged.) ■ Check the temperature adjustment and adjust the set temperature. ■ Make sure that there is plenty of space around the outdoor unit.
11. Trouble Shooting Having trouble? Noise is louder than specifications. Here is the solution. (Unit is operating normally.) ■ The indoor operation sound level is affected by the acoustics of the particular room as shown in the following table and will be higher than the noise specification, which was measured in an echo-free room. High soundLow soundNormal rooms absorbing rooms absorbing rooms Broadcasting Location Reception room, Office, hotel studio, music examples hotel lobby, etc. room room, etc.
KB79U748H01_EN.pm65 19 2011.10.
KD79D904H01_Backcover.fm Page 24 Friday, October 14, 2011 9:47 AM Please be sure to put the contact address/telephone number on this manual before handing it to the customer. HEAD OFFICE: TOKYO BLDG.
