User's Manual

ManualsBrandsMitraStar Technology ManualsElectronicsVDSL IAD

Table Of Contents

DSL-2401HNA-T1CC User’s Guide
Contents
Introduction
- 1.1 Overview
- 1.2 Hardware Connection
- 1.3 LEDs (Lights)
Introducing the Web Configurator
- 2.1 Overview
  - 2.1.1 Accessing the Web Configurator
- 2.2 The Network Map Screen
- 2.3 The Status Screen
- 2.4 The Web Configurator Layout
  - 2.4.1 Title Bar
  - 2.4.2 Main Window
WAN
- 3.1 The WAN Screen
  - 3.1.1 Edit ADSL Ethernet Connection
  - 3.1.2 Edit VDSL Ethernet Connection
Wireless 2.4GHz
- 4.1 Wireless General Screen
- 4.2 More AP Screen
  - 4.2.1 Edit More AP
- 4.3 MAC Authentication Screen
- 4.4 The WPS Screen
- 4.5 The WDS Screen
- 4.6 The WMM Screen
- 4.7 Scheduling Screen
  - 4.7.1 Add or Edit Schedule
- 4.8 Advanced Screen
Wireless 5GHz
- 5.1 Wireless General Screen
- 5.2 MAC Authentication Screen
- 5.3 The WPS Screen
- 5.4 Advanced Screen
- 5.5 Wireless Station Information
LAN
- 6.1 The LAN Setup Screen
- 6.2 The Static DHCP Screen
- 6.3 The IP Alias Screen
- 6.4 The UPnP Screen
- 6.5 The IPv6 LAN Setup Screen
Static Route
- 7.1 Configuring Static Route
  - 7.1.1 Add/Edit Static Route
- 7.2 IPv6 Static Route
  - 7.2.1 Add/Edit IPv6 Static Route
- 7.3 The DNS Route Screen
  - 7.3.1 Add/Edit DNS Route
- 7.4 The Current Route Screen
Quality of Service (QoS)
- 8.1 The QoS General Screen
- 8.2 The Queue Setup Screen
  - 8.2.1 Edit a QoS Queue
- 8.3 The Class Setup Screen
  - 8.3.1 Add/Edit QoS Class
- 8.4 The QoS Monitor Screen
Network Address Translation (NAT)
- 9.1 The General Screen
- 9.2 The Port Forwarding Screen
  - 9.2.1 The Port Forwarding Screen
  - 9.2.2 The Port Forwarding Add/Edit Screen
- 9.3 The Address Mapping Screen
  - 9.3.1 The Address Mapping Rule Edit Screen
- 9.4 The DMZ Screen
- 9.5 The ALG Screen
Dynamic DNS
- 10.1 The Dynamic DNS Screen
Filter
- 11.1 The IP/MAC Filter Screen
- 11.2 The IPv6/MAC Filter Screen
Firewall
- 12.1 Firewall General Screen
  - 12.1.1 Add/Edit Interface Default Policy Screen
- 12.2 Rules Screen
  - 12.2.1 Rules Edit Screen
- 12.3 DoS Screen
  - 12.3.1 The DoS Advanced Screen
Parental Control
- 13.1 The Parental Control Screen
  - 13.1.1 Add/Edit a Parental Control Rule
Certificates
- 14.1 Local Certificates
- 14.2 Trusted CA
- 14.3 Trusted CA Import
- 14.4 View Certificate
VoIP
- 15.1 The SIP Account Screen
  - 15.1.1 Edit SIP Account
- 15.2 The SIP Service Provider Screen
  - 15.2.1 Edit SIP Service Provider
- 15.3 Phone Screen
- 15.4 Call Rule Screen
System Monitor
- 16.1 The Log Screen
- 16.2 The WAN Traffic Status Screen
- 16.3 The LAN Traffic Status Screen
- 16.4 The NAT Traffic Status Screen
- 16.5 The VoIP Status Screen
User Account
- 17.1 Overview
- 17.2 The User Account Screen
System
- 18.1 The System Screen
Time Setting
- 19.1 The Time Setting Screen
Log Setting
- 20.1 The Log Setting Screen
Firmware Upgrade
- 21.1 The Firmware Upgrade Screen
Backup/Restore
- 22.1 The Backup/Restore Screen
- 22.2 The Reboot Screen
Remote Management
- 23.1 The General Screen
- 23.2 The WWW Screen
- 23.3 Telnet Screen
- 23.4 FTP Screen
- 23.5 SNMP Screen
- 23.6 DNS Screen
- 23.7 ICMP Screen
- 23.8 SSH/SCP/SFTP Screen
Troubleshooting
- 24.1 Overview
- 24.2 Power, Hardware Connections, and LEDs
- 24.3 Router Access and Login
- 24.4 Internet Access
- 24.5 Wireless Internet Access
- 24.6 Phone Calls and VoIP
Legal

Chapter 8 Quality of Service (QoS) 69

Table 40 QoS > Class Setup: Add/Edit

LABEL DESCRIPTION

Rule Index Select the (order) number of this rule.

Active Select to enable this classifier.

Classification Order Select an existing number for where you want to put this classifier to move the

classifier to the number you selected after clicking Apply.

Select Last to put this rule in the back of the classifier list.

Ether Type Select a predefined application to configure a class for the matched traffic.

If you select IPv4 (0x0800), you also need to configure source or destination MAC

address, IP address, DHCP options, DSCP value or the protocol type.

If you select ARP (0x0806) (available when you set Interface to From LAN), you can

configure source or destination MAC addresses.

If you select 802.1Q (0x8100) (available when you set Interface to From LAN) you

can configure an 802.1p priority level.

Interface Select whether to apply this class to traffic from the LAN or from the WAN.

To Queue Select a queue to apply to this class (available when you set Interface to From

WAN).

You should have configured a queue in the Queue Setup screen already.

From Interface Select the interface from which the traffic class comes.

IP Address Select the check box and enter the source IP address in dotted decimal notation. A

blank source IP address means any source IP address.

IP Subnet Mask Enter the source subnet mask.

Exclude Select this option to exclude the packets that match the specified criteria from this

classifier.

Port Range If you select TCP or UDP in the IP Protocol field, select the check box and enter the

port number(s) of the source.

Exclude Select this option to exclude the packets that match the specified criteria from this

classifier.

MAC Address Select the check box and enter the source MAC address of the packet.

MAC Mask Type the mask for the specified MAC address to determine which bits a packet’s

MAC address should match.

Exclude Select this option to exclude the packets that match the specified criteria from this

classifier.

IP Address Select the check box and enter the destination IP address in dotted decimal

notation. A blank source IP address means any source IP address.

IP Subnet Mask Enter the destination subnet mask.