User's Manual

ManualsBrandsMitraStar Technology ManualsElectronicsVDSL VOIP

Table Of Contents

HGW-2501GN-R2 User’s Guide
Contents
Introduction
- 1.1 Overview
- 1.2 Hardware Connection
- 1.3 LEDs (Lights)
Introducing the Web Configurator
- 2.1 Overview
  - 2.1.1 Accessing the Web Configurator
- 2.2 The Network Map Screen
- 2.3 The Status Screen
- 2.4 The Web Configurator Layout
  - 2.4.1 Title Bar
  - 2.4.2 Main Window
WAN
- 3.1 The WAN Screen
  - 3.1.1 Edit ADSL Ethernet Connection
  - 3.1.2 Edit VDSL Ethernet Connection
Wireless 2.4GHz
- 4.1 Wireless General Screen
- 4.2 More AP Screen
  - 4.2.1 Edit More AP
- 4.3 MAC Authentication Screen
- 4.4 The WPS Screen
- 4.5 The WDS Screen
- 4.6 The WMM Screen
- 4.7 Scheduling Screen
  - 4.7.1 Add or Edit Schedule
- 4.8 Advanced Screen
LAN
- 5.1 The LAN Setup Screen
- 5.2 The Static DHCP Screen
- 5.3 The IP Alias Screen
- 5.4 The UPnP Screen
- 5.5 The IPv6 LAN Setup Screen
Static Route
- 6.1 Configuring Static Route
  - 6.1.1 Add/Edit Static Route
- 6.2 IPv6 Static Route
  - 6.2.1 Add/Edit IPv6 Static Route
- 6.3 The DNS Route Screen
  - 6.3.1 Add/Edit DNS Route
- 6.4 The Current Route Screen
Quality of Service (QoS)
- 7.1 The QoS General Screen
- 7.2 The Queue Setup Screen
  - 7.2.1 Edit a QoS Queue
- 7.3 The Class Setup Screen
  - 7.3.1 Add/Edit QoS Class
- 7.4 The QoS Monitor Screen
Network Address Translation (NAT)
- 8.1 The General Screen
- 8.2 The Port Forwarding Screen
  - 8.2.1 The Port Forwarding Screen
  - 8.2.2 The Port Forwarding Add/Edit Screen
- 8.3 The Address Mapping Screen
  - 8.3.1 The Address Mapping Rule Edit Screen
- 8.4 The DMZ Screen
- 8.5 The ALG Screen
Dynamic DNS
- 9.1 The Dynamic DNS Screen
Filter
- 10.1 The IP/MAC Filter Screen
- 10.2 The IPv6/MAC Filter Screen
Firewall
- 11.1 Firewall General Screen
  - 11.1.1 Add/Edit Interface Default Policy Screen
- 11.2 Rules Screen
  - 11.2.1 Rules Edit Screen
- 11.3 DoS Screen
  - 11.3.1 The DoS Advanced Screen
Parental Control
- 12.1 The Parental Control Screen
  - 12.1.1 Add/Edit a Parental Control Rule
Certificates
- 13.1 Local Certificates
- 13.2 Trusted CA
- 13.3 Trusted CA Import
- 13.4 View Certificate
VoIP
- 14.1 The SIP Account Screen
  - 14.1.1 Edit SIP Account
- 14.2 The SIP Service Provider Screen
  - 14.2.1 Edit SIP Service Provider
- 14.3 Phone Screen
- 14.4 Call Rule Screen
System Monitor
- 15.1 The Log Screen
- 15.2 The WAN Traffic Status Screen
- 15.3 The LAN Traffic Status Screen
- 15.4 The NAT Traffic Status Screen
- 15.5 The VoIP Status Screen
User Account
- 16.1 Overview
- 16.2 The User Account Screen
System
- 17.1 The System Screen
Time Setting
- 18.1 The Time Setting Screen
Log Setting
- 19.1 The Log Setting Screen
Firmware Upgrade
- 20.1 The Firmware Upgrade Screen
Backup/Restore
- 21.1 The Backup/Restore Screen
- 21.2 The Reboot Screen
Remote Management
- 22.1 The General Screen
- 22.2 The WWW Screen
- 22.3 Telnet Screen
- 22.4 FTP Screen
- 22.5 SNMP Screen
- 22.6 DNS Screen
- 22.7 ICMP Screen
- 22.8 SSH/SCP/SFTP Screen
Troubleshooting
- 23.1 Overview
- 23.2 Power, Hardware Connections, and LEDs
- 23.3 Router Access and Login
- 23.4 Internet Access
- 23.5 Wireless Internet Access
- 23.6 Phone Calls and VoIP
Safety Warnings
New Bookmark

Chapter 5 LAN 44

Table 18 Network Setting > LAN > LAN Setup

LABEL DESCRIPTION

IP Address Enter the LAN IP address you want to assign to your Router. T

he factory default is

192.168.1.1.

IP Subnet Mask Type the subnet mask of your network. The factory default is 255.255.255.0. Your

Router automatically computes the subnet mask based on the IP address you enter,

so do not change this field unless you are instructed to do so.

RIP Version Specify the RIP (Routing Information Protocol)

version, which allows a router to

exchange routing information with other routers.

Direction Specify how much routing information the Router sends and receives on the subnet.

Multicast IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to

establish membership in a multicast group

IGMP Snooping Select Enable

d to activate IGMP Snooping. This allows the Router to passively learn

memberships in multicast groups. Otherwise, select Disabled to deactivate it.

IGMP Quickleave Select Enable

d to immediately removes a port when the Router detects an IGMP

version 2 leave message on that port.

DHCP Select Enable to have the Router assign IP addresses, an IP default gateway and DNS

servers to LAN computers and other devices that are DHCP clients.

Select DHCP Relay to

have the Router forward DHCP requests to the DHCP server.

If you select Dis

able, you need to manually configure the IP addresses of the

computers and other devices on your LAN.

You need to configure the following fields if you select Enable or DHCP Relay.

HCP Relay Server

Address

you set DHCP to DHCP Relay, enter the IP address of the DHCP relay server.

IP Pool Starting

Address

Specify the first of the contiguous addresses in the IP address pool.

Pool Size Specify the size, or count of the IP address pool.

State Select Enable

enable the DHCP conditional serving pool for the IPTV. DHCP server

will offer IP address from the conditional pool if the DHCP request sent from a set-

top box contains the specific Vendor ID.

Gateway Enter the IPTV server’s IP address.

Subnet Mask Enter the IPTV server’s subnet mask.

Pool Start/End Specify the first and last of the contiguous addr

esses

in the IPTV server’s IP address

pool.

DNS Server 1/2 Enter the IPTV server’s first/second DNS server IP address.

VendorID Specify the IPTV’s vendor ID.