I SX-50111 DIGITAL PRIVATE AUTOMATIC BRANCH EXCHANGE (DPABX) POCKET REFERENCE GUIDE FOR MSS3/54 PN 9104-091-120-NA Issue 2, November 1990 "Copyright 1990, MITEL Corporation. All rights reserved. '"'Trademark.
/ PN 91 04-091-120-NA NOTICE The Information contained In this document is believed to be accurate In all respects but is not warranted by Mltel Corporation (MITEL~. The Information is subject to change without notice and should not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mltel and Its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document.
Pocket Reference Guide CONTENTS PAGE 1. NETWORK CONNECTION INFORMATION . . . . . . . . . . . . . 2. WIRING CHARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. WIRING DIAGRAMS . . .. •. . . . . . .. . •. . .. . .. . .. . . . 7 4. EQUIPMENT NUMBERS CHARTS • . • . • • • . . . . • . . • . . . 11 5. FEATURE INDEX . . • . • • . . • . . . . . • . . . . • . . . . . . . . . . 13 6. CUSTOMER DATA ENTRY REGISTERS Load Default Data . • . . • . . . . . • . . . . • . . . . . • . . . . .
PN 9104-091-120-NA CONTENTS (CONT'D) PAGE COMMAND 191 USER SECURITY CODE PROGRAMMING 70 COMMAND 192 RMATS SECURITY CODE •..•...... 71 COMMAND 193 DISA ACCESS CODE . . • . . . . . . . • . . 72 COMMANDS 301 - 310 EXTENSIONS ..•••........ 73 COMMANDS 321 - 330 BLOCK EXTENSION NUMBERING ........•.•.......•.....•.... 74 COMMANDS 341 - 350 BlOCK EXTENSION MEMBERSHIPS . . . . • . . . . . • . . • . . . . . • . . • • . . . 75 COMMANDS 361 - 366 EXTENSION .HUNT GROUPS . . 76 COMMAND 381 STATION RING GROUP . . . .
Pocket Reference Guide LIST OF TABLES TABLE TITLE PAGE 2-1 2-2 Tip and Ring Assignments - Lines . . . . . . . . . . . 3 Tip and Ring Assignments - Trunks . . . . . . . . . 4 2-3 Tip and Ring Assignments - Power Fall Transfer Circuits ............................. 5 2-4 Tip and Ring Assignments - Universal Card . . . 6 4-1 Station EQuipment Numbers . . . . . . . . . . . . . . 11 4-2 SUPERSET/Trunk Equipment Numbers . . . . . . . 12 5-1 Feature lnde>< . . . . . . . . . . . . . . . . . . . . . . . . .
,.~ N Cl ! .!. Cl iI I,D ..
Pocket Referenc:e Guide 1. NETWORK CONNECTION INFORMATION FCC Registration Number BN285B-16887.-MF-E DOC Approval Number 1731975 A FCC Ringer Equivalence Number (REN) 1.08 load Number (Canada) 73A USOC Connector -CO Trunks RJ21X USOC Connector - 2-wlre E&M Trunks RJ2EX USOC Connector - 4-wire E&M Trunks RJ2GX USOC Connector -DID Trunks RJ21X Service Order Code - E&M Trunks (Type I, 2:- and 4-wira) 9.
: ..., ID fA )> 2 I ~ I ~ - c l II) ,2 ... ...
Pocket Reference Guide 2.
PN 9104-091.-120-NA TABLE 2-2 TIP AND RING ASSIGNMENTS - TRUNKS fair Colour Pin W-81. Sl-W W-0 26 1 27 z o-w 28 3 29 4 3(1 5 31 fi 32 7 33 W-G G-W W-BR SR-W w-s s-w A-Bl BL-R R-0 O-R R-G G-R R-BR BR-R R-S S-R BK-BI. BI.-BK SK-0 0-BK Bi'C-G G-Bi'C BK-BR BR-BK BK-S S-BK 8 34 9 35 10 36 11 37 12 38 13 39 14 ~0 15 41 : 16 Y-81. SL-Y 142 17 Y-0 0-Y I 50 :25 - Page 4 v-s s-v 1.
Pocket Reference Guide TABLE 2-3 TIP AND RING ASSICNMENTS POWER FAIL TRANSFER CIRCUITS Pin 26 Pair Colour W-BL BL-W Connection (LS/GS Trunk Card) 41 16 Y-BL BL-Y Sea TIP AND RING ASSIGNMENTS -TRUNKS 42 17 Y-O 0-Y Not Used Not Used 43 18 44 19 Y-G G-Y Y-BR BR-Y STATION T1 STATION R1 ONS LINE CARD Tl ONS LINE CARD R1 TRUNK Tl TRUNK Rl TRUNK CARD T 1 TRUNK CARD Rl STATION T2 STATION R2 ONS LINE CARD T2 ONS LINE CARD R2 TRUNK T2 TRUNK R2 TRUNK CARD T2 TRUNK CARD R2 1 I 45 20 46 21 47 22 48 23 49
~.
Packet Reference Guide 3. WIRING DIAGRAMS 6-WIRI. JACKI (CUS'JOME:R-PII"~D-EDJ CON-T:ROl (;AII.D m !~__ 8-WlRE CAlliE' WliRINO «:USTQMf~-I>I!CMDEOI NOTE$: 1. Ttl~ Allt:NIMNT -coNIOLE c.Af-5 IE PLAiCED 4 ...,.MUM. OF 200m F1IOM THE r;OHI~L OOU>. Z. :C.CNSOL! Mlti"'G PAJRI- 11-li, :1-5. I ......} M:US' B~ K!Pf A5 PAI'RS IN PlANT WI RING. I(A(IUC.
/ "' ~ 1 "' c ; ii -----' L.- --- _ _ _ .
Pocket Reference Guide T ;!!_ UtGS ...... T DN$ ...... Titlt.JNK ., ~· @ 1iiili"t1 TOT 4!5 co 5l
! "'I • I ...
Pocket Reference Guide 4. EQUIPMENT NUMBERS CHARTS TABLE 4-1. STATION EQUIPMENT NUMBERS Slot Cct 1 2 4 3 5 7 6 8 9 10 01 001 017 033 049 065 081 097 113 129 145 02 002 018 034 050 066 082 098 114 130 146 03 003 019 035 051 067 083.
PN 9104-091-120-NA TABLE 4-2 SUPERSET'MITRUNK EQUIPMENT NUMBERS . Slot CCt 1 2 3 4 5 6 7 8 9 10 01 01 09 17 25 33 41 49 57 65 73 02 02 10 18 26 34 42 50 58 66 74 03 03 11 19 27 35 43 51 59 67 75 04 04 12 20 28 36 44 52 60 68 76 05 05 13 21 29 37 45 53 61 69 77 06 06 14 22 30 38 46 54 62 70 78 07 07 15 23 31 39 47 55 63 71 79 08 08 16 24 32 40 48 56 64 72 80 Note: E&M Trunks use ODD Equipment Numbers only.
Packet Reference Guide 5. FEATURE INDEX Feature Index, Table 5-1, lists the programmable features of the SX-5001 system and their corresponding Customer Data Entry fields; TABLE 5-1 FEATURE INDEX Feature Name Abbreviated Dial Command Register Field 100 09 13 07 5 15 c,h j c-f b- J 110 121 - 129 Account Codes (Note: must also enable SMDR.
PN 9'104-091-120-NA TABLE 5-1 (CONT'Dl FEATURE INDEX · Feature Name Automatic Rlngdown Circuit Automatic Night Service Automatic Route Selection and Toil Control Automatic Wake-Up Command Register Field 121 - 129 2 d 301 - 210 c 100 01 - 16 08 100 301 - 310 341 - 350 501 - 580 700 70l - 745 750 751 752 13 01 - 16 01 - 16 1 001- 800 01 - 06 001 - 200 001 - 100 001 - 100 c,e c- I g g h d.e.
Pocket Refereru:e Guide TABLE 5-1 (CONT'D) FEATURE INDEX Feature Name Call Direction Call Forwarding - Busy Call Forwarding - Busy/No Answer Call Forw~rdlng - EMternal Call Forwarding -Follow Me Call Forwarding -No Answer Register 121 - 129 110 121 - 129 2 c 11 4 c - f c 11 12 c- f 100 110 121 - 129 100 121 - 129 e c 4 6 2 110 121 - 129 100 110 121 - 129 DB c- f Call Hold {Extension) 100 110 no Call Pickup 4 09 501 - 580 100 Call Hold Retrieve d b- f b- j c Call Hold (Attendan
PN 9104-091-120-NA TABLE 5-1 (CONT'DI FEATURE INDEX Command Register Field Call Selection 501 - 580 4 5 d b Call Transfer 100 121 - 129 11 c,d 2 8 b 100 121 - 129 11 8 c b-e 110 15 c- 100 121 - 129 11 c,d 2 b b-e Conflict Dialing 100 e Consoleless Operation 100 09 02 Feature Name Camp-On Clear All Features Conference a 08 Contact Monitor ~ Page 16 110 121 - 129 9 3 501 - 580 8 4 5 100 301 - 310 17 01 - 16 c f d c,d,f- I c- f g b-e d- 9 b-e c-e c
Pocket Reference Guide TABLE 5-1 (CONT'D) FEATURE INDEX Feature Name Command Register 100 100 16 c 16 d-h Data Demultiplexer Data Dump/Load Field Data Line Security 121 - 129 3 d Dictation Trunk 151 501 121 501 2 4 9 8 b-e d- g Direct-In lines Direct Inward Dial Trunks Direct Inward System Access (DISA} - 156 - 580 - 129 - 580 100 110 121 - 129 185 501 - 580 4 05 35-37 8 01 - 14 1 4 5 6 7 g-1 c - f d,e c,d e,j d - k b ~ f b. d- J 121 - 129 2 193 01 e b.
PN 9104-091-120-NA TABLE 5-1 (CONT'O) FEATURE INDEX Feature Name Do Not Disturb E&M Trunks Command Register 110 121 - 129 165 33 151 - 156 501 - 580 2 01 - 14 1 1 2 3 4 Field c- f k.
Packet Reference Guide TABLE S-1 (CONT'D) FEATURE INDEX Command Register Field Hunt Groups {Extensions) (See also Log-In Hunt Groups) 110 361 - 366 19- 24 01 02 - 09 c- Hunt Groups (Trunks} 151 - 156 151 - 156 1 Feature Name Identified Trunk Group Incoming Call I dantitlcation Internal Calls to Console Night Answer Point Last Number Redial Line Appearances Lockout Alarm Log-ln Hunt Groups Manual Line Message Register Audit (Printer required; refer to PRINTER).
PN 9104-091-120-NA TABLE S-1 (CONT'D} FEATURE INDEX Feature Name Command Register Field 1DD 151 - 156 10 2 2 185 01 - 14 g f e b-tl c,d 100 110 121 - 129 38,39 Messages - Advisory 121 - 129 7 MessagesCall Me Back 401 - 480 Message Registration 121 - 129 3 Message Waiting • 12 2 c- f c- f El b c Music on Hold 100 09 f Night/Day Switching 185 01 - 14 c,d Off-Premises Extensions 301 - 310 01 - 16 h Originate-Only Extensions 121 - 129 2 c 100 08 c-1 110 121 - 129 501 -
Pocket Reference Guiile TABLE S-1 (CONT'D) FEATURE INDEX Fnture Name Command Register Field 100 16 c- h Remote Maintenance Administration and Test System (RMATS) 100 110 1g2 501 - 580 1 26 1,2 4 5 d c - f b- f d-g b-e Restrictive Station Control 121 - l2g 2 f Reversal Meaning 501 - 580 2 d,e Ring Group 110 381 501 - 580 25 01 - 09 4 5 c ..
PN 9104:-091-120-NA TABLE 5-1 (CONT'O) FEATURE INDEX Feature Name Register field 100 06 c 100 301 - 310 401 - 480 121 - 129 07 01 - 16 01 - 15 c- e d- l c- I 2 j System Security Code Programming 190 01 b-e Test line 100 01 06 ll e.
Pocket Reference Guide TABLE 5-t (CONT'DJ FEATURE INDEX Feature Name Trunk Groups Command Register Field 121 - 129 151 - 156 1 l b-g 2 3 b - k b- h 2 3 b-a b b- i b- f 4 1 501 - 580 b-1 c 4 b- Trunk Intercepts 501 - 580 4 d- k b- f Trunk Signaling DTMF/Rotary Outpulsing 100 151 - 156 2 2 f 9 Trunk-to-Trunk Plus Station Conferencing 100 121 - 129 501 - 580 05 c- I 2 c Unlimited Walt For Dial Tone 151 - 156 2 b User Security Code Programming 180 191 1,2,3 01 b - h Voice
PN 9104-091-120-NA TABLE 5-1 (CONT'D) FEATURE INDEX Feature Name Voice Mall Port {Cont'd} Walt For Dial Tone ~ Page 24 Command 121 301 361 401 - Register 7 129 310 ' 01 - 16 2- 9 366 480 15 151 - 156 2 Field d.
Pocket R11terence Guide 6. CUSTOMER DATA ENTRY REGISTERS Load Default Data &.tn Defaults are listed for each register. On a new Installation, the default data must be loaded as follows. 1. Ensure Power Supply is OFF. 2. $et all Control Card Switches OPEN. 3. Switch Power Supply ON. Wait for Control Card LED to show ?. (The Console displays LOAD DEFAULT DATA?). 4. Within 10 seconds, toggle Status Switch 1 to the CLOSED position and then back to OPEN. Walt for the Control Card LED to dlsplav A.
PN 9104-091-120-NA Access to Programming TABLE 6-2 PROGRAMMING ACCESS FROM THE ATTENDANT CONSOLE TO ACCESS CDE FROM THE ATTENDANT CONSOLE: Note: For read-only access, omit the steps involving the STATUS key. • Press and hold down the STATUS key. • The Attendant Console LCD displays the software identifier and maintenance release number. ~~~~~ MS54-MR~ --- I • Enter a security code {System Security Code default Is 7712 end User Security Code default is 1234).
Pocket Reference Guide TABLE;6-3 PROGRAMMING ACCEss: FROM THE TEST LINE ENTER PROGRAMMING MODE FROM THE TEST LINE l. Status Swlt~h 2 on the Control Card must be CLOSED for : Test Line operation. ! 2. It Is recommended that a SUPERSEt 4"' telephone be used as a Test Line as It has an LCD display. 3. Command 100 Register 1 fields e. f. g must be programmed with the Equipment Number of the Test Line set. Default Is 001. • Press n or dial 70.
PN 9104-091-120-NA TABLE 1-4 TEST LINE SOFTKEV EQUIVALENT KEY SEQUENCES Console Test Ll~e Softkey Soft~y ENTER YES, NEXT FWO - ... Test Line Key Sequence .., *2 "'3 *5 DELETE WFOT ' 1 "6 PAUSE '' EXIT "7 EXIT I *4 VIEW •o SAVE SAV~ ** QUIT CANqEL "II Note; The VIEW, DELETE, WFOT end PAUSE softkeys are used In programming ARS. Refer to Section MITL9104-091..1~20-NA, Automatic Route Selection, for more iitformation.
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS System Maintenance a b c d e t g h 0 1 1 1 0 D 1 0 0 - Disable. 1 = Enable unless indicated otherwise c: Automatic Diagnostics d: RMATS Protocol Selection Oa CCITI 1 • North American e.f.
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'D) Attendant Functions I: I: I:[: I: I: 0 • Disable, 1 ~ Enable unless Indicated otherwise c: Executive Busy Override (Console) 0 =Disable 1 ~ Enable except on I!C Trunks 2 • Enable on all Calls d: Console Inhibit e,f: RESERVED Page 30
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) Tone and Ringing Control B b c d e f g h i l 0 3 0 1 4 1 1 2 0 0 0 • Disable. 1 • Enable unl.
PN 910-4-091-120-NA l,j: DTMF/Call Progress Tones Selected If field H • 1: 00 - 09 a DTMF Digits 0 - 9 10 ,. DTMF sign 11 =OTMF #sign * rr field H = 2: 00: Dial Tone 01 • Busv Tone 02 =Reorder Tone [:1:1:1:1 These field values should not be changed.
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) Trunk Connections II b c d 0 5 D 0 e 0 ~ f 0 - - g h i 0 0 L-~_j = 0 Disable, 1 ., Enable unless indicated otherwise c: CO To CO Connection d: E&M To E&M Connection e: CO To E&M Connection 0 5 Disable 1 • Enable for Incoming CO trunks only 2 • Enable for Outgoing CO trunks only 3 ,.
PN 9104-091-120-NA COMMAND 1"00 SYSTEM OPTIONS (CONT'D) Station Attribute& a b c d e f 9 0 6 0 1 0 0 0 c: Station $wrtchhook Flash Timing 0 1 2. 150-750 ms 150-1500 ms ~ Flash Is Release 3 : 90 ms Calibrated Flash a a d: Station Olgit Coliection 1 = 10 pps 2.
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) SUPERSET Telephone Attributes a b 0 -- 7 '-- c 0 - L___ a d 0 '--- 1 - 0 = Disable, 1 ..
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'D} Overflow Control a 0 - c b 8 ,_ 2 d e f g 1 3 2 0 L_ - h I 0 0 - I c: Overflow Mode In Oay Service 0 ~Disable 1 lmmediele Switching to Overtlow 2 • Automatic Switching to Overflow after Timeout 3 - Automatic Switching to Night Service = d: Night Bell Mod!' In Night Service 0 ..
Poeket Reference Guide COMMAND 100 SYSTEM ·oPTIONS (CONT'D} Features Selection 1 a b c 0 9 , d e f g h j 0 0 0 0 0 0 0 = Disable.
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'D) Features Selection 2 8 b c d e f g h I I 1 0 1 0 0 0 0 0 o I 0 = Disable, 1 • Enablli! unless indicated otherwise c: Automatic Wake-Up 0 • Disable 1 Enable with Wake-Up tone 2 ..
Pocket Reference Guida COMMAND 100 SYSTEM OPTIONS (CONT'D) Timeout Selection a b c d e f 9 h 1 1 3 3 3 3 1 1 c: Timed Recall - Camp-On (Trunks) 1 - 7 X 10 seconds d: Timed Recall - No Answer 1 - 7 X 10 seconds e: Timed Recall - Call Hold (Extension) 1 - 4 X 1 minute f: Timed Recell - Call Hold (Attendant) 1 - 7 X 10 secontls g: Cell Forwerd No Answer Timeout 1 - 7 X 10 seconds h: Drop Unanswered Trunks After 5 Minutes 0 ~ Disable, 1 = Enable Page 39
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'O) Message Waiting 1:1:r: 1:r:rl c: Message Waiting System Enable 0 • Disable 1 ; Enable with Lamps 2 : Enable with Bells 3 "' Enable with 30-second Manual Line d: Message Waiting Indication 0 .. Always 1 " During Day Service Only e: Message Waiting Indication Interval {1 - 4) X 5 minutes f: Message Waiting Automatic Cancel 0 ..
Pocket Reterence Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) Automatic Route Selection (ARS) a b 1 3 c 0 d 0 a f g \l I l 0 0 0 0 1 0 0 • Disable, 1 • Enable unless Indicated otherwise c: ARS Enable d: ARS Attendant Bypass a: ARS Alarms f: ARS Return Dial lone g: Expensive Route Warning lone h: Attendant ARS Routing Class of Service (RCS} 0 • ARS Does Not Apply 1 "RCS 1 2=RCS2 3 aRCS 3 1: ARS lnterdiglt llmeout 0 = 5 seconds 1 a 10 saconds j: Abbreviated Dial ARS Bypass Page 41
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'D) Messa~e System Detail Renording (SMDR) I:I:1:I:I:I~ r: 1:I~ l~ T: I · 0 ~ Disable, 1 " Enable unless Indicated otherwise c: SMOR System Enable 0 1 2 3 "Disable = Enable Incoming Trunks Calls Only " Enable Outgoing Trunks Calls Only = Enable Both Incoming and Outgoing Trunk Calls d: Record Meter Pulses a: long Call Indicator f: Incoming Calls Record Only COs g: Drop Cells Of less Then 8 Digits h: Drop Incomplete Outgoing Calls i: Overwrite Queued P
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) Account Code Control r:tw-:r.
PN 9104-091-120-NA COMMAND 100 SYSTEM OPTIONS (CONT'D) Printer Control a b e d 8 f g h 1 6 0 4 0 8 1 0 ' 0 • Disable. 1 • Enable unless Indicated otherwise c: Data Demultiplexer Enable d: Printer Baud Rete 0" 110 1 - 150 2-300 3 .. 600 5- 1800 6:2400 7-4800 8-9600 4.
Pocket Reference Guide COMMAND 100 SYSTEM OPTIONS (CONT'D) Contact Monitor B b c d e 1 7 0 D D c.d,e: Contact Monitor Night Answer Point (During Attendant In hi bit or Night Service) ODD = Console 001 - 160 • Station Equipment Number 161 m Night Bell . - ,.~- _.,,P~~.
PN 9104-091-120-NA COMMAND 110 FEATURE ACCESS CODES a b c 0 1 0 0 2 5 0 PAGING ACCESS 0 3 5 1 CALL HOLD 0 4 5 2 0 5 5 3 0 6 5 4 0 7 5 5 d e f DIAL ACCESS TO ATTEI'DAAIT CALL I-IJLD RETRIEVE - LOCAL I CALL HOLD RETRIEVE - REMOTE I DIAL CALL PICKUP SYSTEM ABBREVIATED DIAL ACCEl I 0 8 5 6 0 9 5 7 TAFAS PICKUP \ 0 5 8 CALL FOOWARD - NO ANSWER 1 1 5 9 CALl FORWARD - BUSY T 2 6 0 CALL FWD - BUSY/NO ANSWER 1 3 7 0 PROGRAMMING ACCESS c - f: Access C
Pocket Reference Guide COMMAND 110 FEATURE ACCESS CODES (CONT'D) a b c d 1 4 7 1 1 5 4 4 4 CLEAR ALL FEATURES 1 6 4 5 1 CALL PAAK (ATTEI'LIAAIT) 1 7 4 5 2. CALL PAAK (ATTEI'LIANT) 2 1 8 4 5 3 CALL 1 9 4 9 l H..M GROJP 1 ACCESS 2 0 4 9 2 H.JilT GROOP 2 ACCESS 2 1 4 9 3 f-UilT GROOP 3 ACCESS 2 2 4 9 4 fUoiT GROJP 4 ACCESS 2 3 4 9 5 1-lNT GROOP 5 ACCESS 2 4 4 9 6 1-lNT GROOP 6 ACCESS 2 5 4 9 7 2 - 6 L_ - - e f ATTEI'Il!WT FI.J>.
PN 9104-091-120-NA COMMAND 110 FEATURE ACCESS CODES (CONT'D) c e f a b 2 7 2 8 7 5 Acoo..M' CCDE ENTRY 2 9 7 6 RESERVED 3 0 6 1 OIRECTED/ATT CALL PICKUP 3 1 7 4 3 2 6 2 CALLBACK SETUP 3 3 6 3 DO OOT 0 ISn.JRB 3 4 6 4 H.
/ Pocket Reference Guide COMMANDS 121- 129 CLASSES OF SERVICE 1 - 9 Regl5ter 1 1: I:J: r: I:I:I~ I: I:J : 0 " Disable, 1 ..
PN 9104-091-120-NA COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 (CONT'D) Register 2 8 b c d e f g h i I k. 2 1 1 0 0 0 1 0 0 0 0 0 = Disable, 1 c Enable unless Indicated otherwise b: Swltchhooi
; .:..: c: 0 '
PN 9104-091-120-NA COMMANDS 121 ... 129 CLASSES OF SERVICE 1- 9 (CONT'D) Register 3 ' 8 b c d e f g h I I k 3 1 1 0 1 0 1 0 0 1 0 0 • Disable, t * Enable unless Indicated otherwise b: Automatic Callback Busy/No Answer c: Paging Access d: Data line Security .
Pocket Reference Guide COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 (CONT'D) Rag later 4 I : I: I: I : I: I: I: For fields b - I: I : I: e:: D ~ Disable all Call Forwarding 1 e Allow forwarding of trunks or extensions to Internal numbers only 2 • Allow forwarding of extensions only to • Internal or external numbers 3 • Allow forwarding of trunks or extensions to Internal or external numbers b: Call Forward - Follow Me c: Call Forward - Busy d: Call Forward - No Answer e: Cell Forward - Busy/No Answer F
PN 9104-091-120-NA COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 {CONT'D) Register 5 II b c d e f g 5 1 1 1 1 1 1 h , I I 1: 1 1 0 0 c Disable, 1 - Enable unless Indicated otherwise b: Abbreviated Dial Numbers 10 - 19 or 100 - 199 c: Abbreviated Dial Numbers 20 - 29 or 200- 299 d: Abbreviated Dial Numbers 30 - 39 or 300-399 e: Abbrevieted Dial Numbers 40 - 49 or 400- 499 f: Abbreviated Dial Numbers 50 - 59 or 500- 599 g: Abbreviated Dial Numbers 60 - 69 or 600-699 h: Abbreviated Dial N
Pocket Reference Guide COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 (CONT'D) Register 6 ~ ~ o ~ Disable, 1 • Enable unless indicated otherwise b: NOT USED c: Outgoing Access To E&M Tie Trunks d: Outgoing Access To CO Trunks Page 55
P}ll 9104-091-120-NA COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 (CONT'D) Register 1 8 b c d e f 7 1 0 0 0 0 '- g h 0 0 - 0 • Disable, 1 c Enable unless Indicated otherwise b: SUPERSET 4 Message Programming c: Account Code Entry 0 • Not allowed 1 c Optional 2 • Required for Toll Calls Only 3 • Required for All Calls (Toll 8t Non-Toll) d: Auxiliary Attendant Position e: Directed Call Pickup f: Directed Call Pickup Security g: Hunt Group Login h: Lock-out Alarm Page 56
.;/ 2=r,.. Poc:ket Reference Gui~~../ ---------------------------------------· COMMANDS 121 - 129 CLASSES OF SERVICE 1 - 9 (CONT'D) Register 8 l:ltl:l:, 0 ~ Disable, 1 c Enable unless Indicated otherwise b: Extension Camp-on c: CO Trunk Camp-on cl: Inward Dial Trunk Camp-on e: DID Restriction Page 57 ' ·c. s.
PN 9104-091-120-NA COMMANDS 151 - 156 TRUNK GROUPS 1 - 6 Register 1 [ffil:l:l:ltl:[j b: Trunk Select (0 ~ Automatic} c: Type of Hunting o " Circular, 1 = Terminal d: Overflow Trunk Group 1 - 6 0 =Disable e: Identified Trunk Group 0 = Disable, 1 " Enable f - 1: Trunk Group Access Code Defaults: Cmd 151 = 9, Cmd 152 = 8. Cmd 153 ":78, Cmd 154 e 79 Cmd Hi!. • blank.
Pocket Reference Guide COMMANDS 151 - 156 TRUNK GROUPS 1 - 6 (CONT'D) Register 2 1:1:1:1:1: I: 1:1:1:1:1:, 0,. Disable, 1 =Enable unless indicated otherwise b: Wait For Dial Tone 0 = No w&it outpulsa attar delay 1 ~ Wait up to 5 seconds. then outpulse anyway 2 " Check for dial tone every 5 seconds 3 = Unlimited wait with detection by user c: Dial Tone Detection Timing 0 = 120 ms required, 1 = 40 ms required tl: Delay Before Outpulsing l - 5 seconds Note: Wait for Dial Tone must be set too.
PN 9104-091-120-NA g: DTMF or Rotary Outpulslng 0 .. OTMF, 1 c Rotary 2 • Rotary, Disable Outgoing Audio Until Answer 3 "' Rotary, Inhibit DTMF Until Answer h: Simulate CO Dial Tone 1: Trunk Group SMDR Enable j: Trunk Group Last Number Redial k: Trunk Group Manual ES.
Pocket Reference Guide COMMANDS 151 - 156 TRUNK GROUPS 1 - 6 (CONT'D) Register 3 I:J:l : I_: I: I:I:j: b: Message Registration o = Disable, 1 • Enable c: Count Additional Message Units 0 • Disable, 1 • Enable 2 • Enable, Insert Pseudo Message Unit every 6 Seconds 3 • Enable, Insert Pseudo Message Unlt every 60 Seconds d,e: Initial Message Unit Charge 00- 99 Units t,g: Additional Massage Unit Charge 00- 99 Units h: Pseudo Answer Timer 1 - 1 X 10 secomls Page 61
PN 9104-091-120-NA COMMANDS 151 - 156 TRUNK GROUPS 1 - 6 (CONT'D) Register 4 I a b c d e ' 4 0 0 0 0 ! b: Sending Answer On Incoming Dial Trunks 0 ~ 1 ~ 2 ~ Send Answer When Answer Received (Supervision Is Answer Only) Send Answer After End of Dialing (Time-out} Send Answer Upon Accessing OutgoIng Trunk c: Behind PABX Operation 0 ~Disable 1 ~ Enable. Flash is Loop Disconnect 2 ~ Enable, Flash is Riog Ground d: Behind PBX Recall Signal Duration 0 = 500 ms.
Pocket Reference Guide COMMAND 180 USER PROGRAMMING ACCESS Register 1 a b c d e f Q 1 0 0 0 0 0 0 0 " Disable, 1 m Enable unless Indicated otherwise b: Command 100, System Options c: Commands 121 - 129, COS Programming d: Command 110. Feature access Codes e: Commands 301- 310.
PN 9104-Gtt-120-NA COMMAND 180 USER PROGRAMMING ACCESS (CONT'D) Reglaur 2 un l:_ma~ m: 0 .. Disable, 1 ..
Pocket Reference Guide COMMAND 180 USER PROGRAMMING ACCESS (CONT'D) Register 3 a b c d e t 3 0 0 0 0 0 0 • Disable, 1 " Enable unless Indicated otherwise b: Command 185, Function Key Programming c: Com111and 190, System Security Programming d: Command 191, User Security Code Program- ming e: Command 193, DISA Access Code Programming f: Command 192. RMATS Security Code Pro- gramming Note: Fields c and f should be always disabled.
PN 9104-091-120-NA COMMAND 185 ATTENDANT CONSOLE FUNCTION KEYS 8 b c d 0 1 1 0 FIJ£TI CJ>J key 0 2 l 4 STATUS key 0 3 0 7 TRLfl( 0 4 0 4 CALL BLOCK key 0 5 0 5 OVERFLON 0 6 0 3 PAGE 0 7 0 6 WAKE-UP key 0 8 0 1 MSG REG key 0 9 0 2 OVERRIDE 0 0 9 MESSAGE key 1 1 i 5 BOTH _key 1 2 1 3 SWAP key 1 3 1 1 BELL key 1 4 2.
Pocket Reference Guide COMMAND 1BS ATTENDANT CONSOLE FUNCTION KEVS (CONT'D~ e.b: Key Number (l-14) c,d: Key Function: 00 " Unassigned ~ Message Registration /Restrictive Station Control 02 a OVerride 03 =Page 04 • Call Block 05 = TAFAS Overflow 06 .. Automatic Wake-up 0.7 = Trunk Status 08 ~ Account Code Entry 09 = Message Waiting 10 = Function 11 • Bell Mute 01 12 =Night 13 = Swep/Splft 14 =Status 15 .. Both 16 • Room. Status 1.
Pocket Reterence Guide COMMAND 190 SYSTEM SECURITY CODE Register 1 a , b c d e 7 7 7 2 b: System Security Code 1st Digit c: System Security Code 2nd Digit D-9 d: System Security Code 3rd Digit e: System Security Code 4th Digit P1ge &9
PN 9104-091-120-NA COMMAND 191 USER SECURITY CODE PROGRAMMING Register 1 8 b c d e 1 1 2 3 4 b: User Security Code 1st Digit c: User Security Code 2nd Digit 0 d: User Security Code 3rd Digit e: User Security Code 4th Digit Page 70 ~ 9
PoCkl!lt Reference Guide COMMAND 192 RMATS SECURI1'V CODE Register 1 a , I b c d e f 0 2 4 6 aI b: RMATS SecuritY Code 1st Digit c:: RMATS Security Code 2nd Digit d: RMATS Security Code 3rd Digit I 0 - 9 I 0 - 9 e: RMATS Security Code 4th Digit f: RMATS Security Code 5th Digit Register 2 8 b c d 9 f 2 1 3 5 7 9 b: RMATS S9curlty Code 6th Digit c: RMATS Security Code 7th Digit d: RMATS Security Code Sth Digit e: RMATS Security Code 9th Digit f: RMATS Security Code lOth D
PN 9104-091-120-NA COMMAND 193 DISA ACCESS CODE Register 1 ~ GEEE b: DISA Access Code 1st Digit c: DISA Access Code 2nd Digit 0- 9 d: OISA Access Code 3rd Digit Note: Callers on a DISA Trunk with DISA Access Code Required enabled In its Class of Service must enter the Access Code. By default, the OISA Access Code Is not required and cellars have lmmediete access to SX-50 system features.
Poc:ke.t Reference Guide COMMANDS 301 - 310 EXTENSIONS i·itiTI:I: 1:1:1: 1~ I:m a,b: Circuit number 01 - 16 (Ol - DB for COV Card) Note: Even circuit numbers are Invalid for the OPS Una Card.
PN 9104-091-120-NA COMMANDS 321 - 330 BLOCK EXTENSSON NUMBERING 8l~R:lTI ITJE a.b: Circuit number of First Extension In Block 01 - 16 c.d: Circuit number of last Extension ln Block 01 - 16 .
Poeket Refaranee Guida COMMANDS 341 - 350 BLOCK EXTENSION MEMBERSHIPS a b c d e f g 0 1 0 1 1 1 0 h 0 - - a,b: Circuit number of First Extension in Block 01 - 16 c,d: Circuit number of Last Extension in Block 01 - 16 e: Class of Service 1 - 9 D = No Class of Service f: Pickup Group 1 - 7 0 =No Pickup Group g: ARS Routing Class of Service 0 s ARS Does not Apply 1 • RCS 1 2 = RCS 2 3 • RCS 3 4 • Attendant Selectable RCS h: OPS Loop Length 0 1 =Short (under 2 km) c Long (over 2 km} Pa
PN 9104-091-120-N~ COMMANDS 361 - 366 EXTENSION HUNT_ GROUPS ~ ~ b: Hunt Type 0 ..
Pocket Reference Guida COMMAND 381 EXTENSION RING GROUP rrtr'T·J a: Ring Group Member Number 1 - 9 b - e: Extension Number 1 - 9999 Page 77
PN 9104-091-120-NA COMMANDS 401 - 480 SUPERSET TELEPHONE LINES I·I·I:I:I:I:I~ I~ I:I *1 tor Key Number 01, 0 for key~ numbered 02 - 15 a,b: SUPERSET Telephone Key Number c: Line Appearance Type 0 = Speed Dial Key 1 = Prime Line 2 =Key line, 3 = Multiple Call line 4 " Direct Trunk Select 5 = Direct llne Select 6 = Private line 7 Personal Outgoing line 8 = Attendant Function Key (Auxiliary Attendant only} 9 = Mes~age Waiting Key {Programmable on Key 03 only and valld on SUPERSET 3 Sets only} = d: Ringing
Pocket Reference Guide d,e; Attendant Function Key (Line Appearance Type • 8 onlY) 01 ~DIAL 0 02 = DO NOT DISTURB 03,. RECALL 04 =HOLD 1 05,. HOLD 2 06,. HOLD 3 07 • LDN 1 08 c LDN 2 09cLDN3 10 ~ MESSAGE WAITING 11 = MSG REGISTER 12 ,. NIGHT SERVICE 13 " OVERFLOW Note: A maximum of five appearances of each Auxiliary Attendant function key can be programmed on the SX-50 DPABX.
PN 91 04-091-120-NA COMMANDS 501 - 680 TRUNKS 41 - 80 Register 1 B b c d e f g h I I 1 1 1 1 1 0 1 0 1 0 co 1 2 1 3 1 0 1 0 2 1 E8M 1 0 1 6 1 1 0 3 I 2 om I 0 - -- 0 • Disable, 1 • Enable unless indicated otherwise b: Trunk Group Membership 1 - 6 {0 • Incoming Calls Only) c: Trunk Alarm Control d: Trunk Hardware Type 0 1 2 3 4 5 6 " • • " • " • Short Analog CO Trunk Long Analog CO Trunk Analog Toll Office Analog Tie Trunk Satellite Tie Trunk Short Analog DID Tr
Pocket Reference Guide 1: Trunk use 0 ~Disabled 1 • Used· as a CO 2 • Used as an E&M Trunk 3 .. Used as a DID Trunk ]: Trunk Dialing Type 0 • Dll, 1 • DISA.
PN 9104-091-120-NA COMMANDS 501 - 580 TRUNKS 01 - 80 (CONT'D) Register 2 I: I : I: I: I : I : I: I : I : I b: Trunk Outpulsing Make/break Ratto 0 ~ 60/40, 1 = 65/35, 2 a 30/20, 3 • 35/15 c: Disconnect Supervision Guaranteed? 0 =No, 1 =Yes d: Disappearance of Reversal 0 = Is Ignored. 1 a means Disconnect a: Reversal Meaning On Call Origination 0 = Not Incoming Call, l =Incoming Call f: Disconnect Timing 0 • 60 msec 1 c 500 msec 2 a 1.5 sec 3 = 4.0 sec 4 m 10.
Pocket Reference Guide COMMANDS 5.
PN 9104-491-120-NA TABLE 6-5 E&M MODULE SWITCH FUNCTIONS , Function Switch OPEN - PBX to Une • +3 dB CLOSED - PBX to Line " -13 dB 2 OPEN - Una to PBX • -4 dB CLOSED - Line to PBX • -11 dB 3 OPEN - Complex Balance Enabled CLOSED - 600 Ohm Balance Enabled 4 OPEN - 600 Ohm Balem:e Enabled CLOSED - Complex Balance Enabled 5 OPEN - 4-Wire Operation CLOSEO - 2-Wire Operation 6 OPEN - Type 5 Signaling CLOSED - Type 1 Signaling 7 NOT USED 8 NOT USED Note: The settings of Switch 3 and Switch 4 mu
Pocket Reference Guide COMMANDS 501.- 580 TRUNKS 01 - 80 (CONT'D) Reglster4 u·l :I:I:I:I:I~ I:I~ I~ I:I fl: 0 for CO and DID. 1 for El!oM 0 • Disable, 1 • Enable unless indicated otherwise b: Dictation Trunll(for LS/GS Trunks) c: Inter-ringing Delay (for lS/GS Trunks) 3- 9 seconds d: Day Answer Mode or Day Illegal Number Intercept (DID/DISA) D ~ Direct-In line 1 =LON 1 2 •LON 2 3 • LDN3 e,f.
PN 9104-091-120-NA COMMANDS 501 - 580 TRUNKS 01 - 80 (CONT'D) Register 5 8 b c d e f ' 5 0 o· tl l! 0 0 - Disable, 1 .. Enable unless Indicated otherwise b: Night Answer Mode or Night Inward Dial Trunk Intercept (010/DISA) 0 s 1 & Flexible Night Service LON 1, 2 " LON 2.
PDGket Reference Guide COMMANDS 501 - 580 .
PN 9104-091-120-NA COMMANDS 1101 - !i80 TRUNKS 01 - 80 (CONT'D) Register 7 a 7 -- b c 0 2 ·- ·- b,c: Incoming (01 - e d 4 -- 3 3 L_ - Sel~ure 15l~o: f - g h I 0 2 0 _,I - Debounce Timer 10 ms d: Wink Timer (3 - 6) J< 50 ms e: Permanent-Signal Partial-Dial Timer (\ - 6) x 5 sec f: DID Disconnect Timer {3 - Ill x 50 ms g - i: Rei &lise Acknowledge Timer 002 - 120 sec Page 88
Po~:ket Referen~:e Guide COMMAND 600 VERIFIED AUTHORIZATION CODES (VAC) PROGRAMMING ITIITII :I:I:I~ I~ I:I I I:I I~ I j k m a,b,c: Register Number 001 ~ 999 d: VAC Activation 0 • Disable, 1 B Enable e: COS for Authorization Code 1 - 9 • COS (for VAC) 0 ~Disable f: ARS Routing Number 1 - 3 ~ ARS RCS (for VAC) 0 ..
PN 9104-091-120-NA COMMAND 700 ARS DIGIT COMPARISON TABLE FfEJTrf4U i:i,b,c: Entry Number 001 - 800 d.
Pocket Rafarence Guide COMMANDS 701 • 745: ARS TIME-OF-DAY TABLE [1:1:1:1:1;1:1:1~1~1:1~1:[1 a: Period Number 1 - 6 b,c: Start Hour 0()- 23 d,e: Start Mlnute 00 - 59 f,g,h: RCS 1 Route List 0()1 - 200 l,j,k: RCS 2 Route List 000 • access l,m,n: RCS 3 Routa List restricted Page 11
Pl\1 9104-091-120-NA COMMAND 750 ARS ROUTE LIST TABLE Urr~ I~ I:I:I~ I:I~ I~ I:FJJIUJ a,b,c: Route List Number 001 - 200 d.e.f: 1st Choice Route Number g,h,i: 2nd Choice Route Number j,k.
Pocket Reference Guida COMMAND 7S1 ARS ROUTE TABLE I· I· I: I: I: I: I: I: I e,b,c: Route Number 001 - 100 d: Trunk Group Number 1 - 6 e,f,g: Digit Modification Entry Number 001 - 100 h: Toll Calls (Req'd for Account Code Bypass) o • Non-Toll 1 • Toll Page 93
l_ PN 1104-GBl-120-NA COMMAND 752 ARS DIGIT MODIFICATION TABLE ITT' I~ I·J :1·-__,I~ I a,b,c: Digit Modification Number 001 - 100 d.
Pocket Reference Guide 7. PROGRAMMING ERRORS Alarm Messages 1\ave the following format; A 12 0034 NO TRUNK RElEASE AGK. 05/02 Al&rm Code Equipment Nwroer Explan&torv message Slot/Circuit (whare applicable) The 7-segment Status Display lED is located at the right edga of the Control Card, under the cover. A flashing digit shows tha number of alarms In the alarm queue. o Is displayed If there are no alarms. After a power-up or reset the display can show a steadily lit digit. This is an alarm code.
\ PN 9104-091-120-NA TABLE 7-1 PROGRAMMING ERROR CODES Error Code Description E01 Illegal Command Identity E02 Digit keyed while Access Mode Error displayed. E03 Directory Number already eKists.
Pocket Reference Guide TABLE 7-1 (CONT'D) PROGRAMMING ERROR CODES Error Code ·- Description E22 Device must be an eKtenslon. E23 ARS Busy - Calls In progress E24 DJglt String already programmed E25 Digit String register overflow E26 No Digit String entered E27 Digit aree Is full. E28 The start time entered for this time period Is earlier than or equ1111 to the start time of the preceding period. Time periods must be entered In ascending order.
PN 9104-091-120-NA TAB.LE 7-1 (CONT'D) PROGRAMMING ERROR CODES Error Code Description E4D Invalid Auxiliary Attendant Equipment (must be a SUPERSET 4 Telephone). E41 Auxiliary Attendant not Idle E42 Auxiliary Attendant programming conflict E43 Invalid base Directory Number (Occurs when programming Commands 301 - 310). E44 Invalid Directory Number (Occurs when programming CommandS 321 - 330). E45 Contact monitor conflict.
Pocket Reference Guide 8. ATTENDANT AND MAINTENANCE FUNCTIONS TABLE 8-1 ATTENDANT AND MAINTENANCE FUNCTIONS Function Code Night Service - ON *11 Night Service - OFF *12 Identify Alarm and Clear *13 Set 12-Hour Clock *14 + 2-diglt hrs, 2-diglt minutes Set 24-Hour Clock * 15 -+ 2-diglt hrs, 2-digit minutes Lamp Test *16 Music ON *17 Music OFF *18 Access Trunk *19 +Trunk Eqpt. No. Trunk Emergency Release *20 -+ Trunk Eqpt. No. Night Answer Point *21 + Trunk Eqpt No. + Answer Pt. Ext.
PN 9104-G91-t2D-NA TABLE 8-t (CONT'D) ATTENDANT A"ND MAINTENANCE FUNCTIONS Function Code Cancel AU Alarms. Alarm Indicators and Busy-Outs *32 Busy Out Trunk ~1 Busy Out OTMF Generator ~2 Busy Out DTMF Receiver *43 + OTMF Receiver Number Busy Out Dlal Tone Detector *44 + Detector No. Change Verified Authoril!allon Code ~5 + Trunk Eqpt. No. Unbusy Trunk *51 + Trunk Eqpt. No. Unbusy DTMF Generator *52 Unbusy OTMF Receiver it53 • OTMF Receiver Number Unbusy Dial Tone Detector *54 .,.
·Po~:ket Refvren~:·e G1.1ide TABLE 8-1 (CDNT'D) ATTENDANT AND MAINTENANCE FUNCTIONS Fun~:tlon Set System Date Code *80 + DD-MM-YY Room Status *81 Room Status Printout *82 Do Not Disturb *85 Alarm Print - Automatic *90 .. 1 Alarm Print - Disable *90 ..
...c "U .-.. = 2 ,.' 0 ... ....!. .b ID ~ 0 ID ...
Pocket Reference Guide 9. TROUBLESHOOTING - ALARM CODES TABLE 9-1 TROUBLESHOOTING - ALARM CODES Code ' I Cause Procedure 01 Failed non-volatile RAM test. Reset system. If alarm persists, replace Generic Module. 02 Checksum error in non-volatile AAM test. Reload default data, reprogram. If alarm persists. replace Generic Module. 03 failure in read/write test of non-volatile RAM. Clear alarm. If alarm persists, replace Generic Module. 04 Checksum error in Peripheral Processor PROM.
PN 9104-G91-120-NA TABLE 9-t (CONT'D) TROUBLeSHOOTING - ALARM CODES Cade cause Procedure 21 Dial tone detector felled test and has been busied-out Follow Peripheral Equipment Troubleshooting Procedure, In Section MITL9104-091-350-NA. 22 Station has failed a loopback test. Reset system. If error recurs, replace Line Card. 23 Three-party conference circuit failed test. Reset system. if error recurs, change Control Card. 24 PTMF Receiver felled test Follow Peripheral and has been busied-out.
Packet Reference Guide TABLE 9-1 (CONT'D) TROUBLESHOOTING - ALARM CODES Code Cause Procedure 29 Device Is not being scheduled correctly. Report occurrence In Trouble Log. Include details of device, time and operations when alarm occurred. 30 Attempt to enter CDE data value outside of allowed range. Refer to Section MITL9104-091-210-NA (CDE) for valid data range. Correct entry. 40 Console dead due to hardware failure. Reset system. Try another corisole. Replace Control Card.
PN 9104-()91-120-NA TABLE 9-1 (CONrD) TROUBLESHOOTING - ALARM COOES Code Cause Procedure 81 ARS Route Priority table not programmed. Program Route Priority table. 82 ARS Route Ust not -programmed. Program Route Ust. 83 ARS Digit Modification Table not programmed. Program Olglt Modification Table. 84 (ARS) selected trunk group programmed for manual dial tone verification. Change Trunk Group programming. 85 Set Is locked out. Clear alarms (*32). Replace the set's handset.
( Packet Reference Guide RMATS Parameters 9.01 The modem used to access RMATS must have the following characteristics: • Bell Standard 103 or equivalent • 300 Baud • Even parity • 7 data bits, 2 Stop Bits • Full Duplex • Originate mode.
..• : ao 0 (D > 2 ll!lI I ... I 0 ID 0 ID ,.... ... .
Pocket Reteren;e Guide 10. TROUBLESHOOTING - COMMAND REGISTERS COMMAND 900 UNIVERSAL CARD RESET 1911111 Slot Null'ber When the 'RESET' softkey Is pressed, the Universal Card In the slot Indicated is reset. This command has no effect on other card typss. Note: Key sequence '"4' Is equivalent to 'RESET'.
PN 9104-091-120-NA COMMAND 980 - SYSTEM STATUS DISPLAY System Status Display shows the status of Dial tone detectors, the Tona Generator. OTMF Receivers and diJgnostlc tests.
Pocket Reference Guide COMMAND 980 - SYSTEM STATUS DISPLAY (CONT'D) Register 2 Register NuiOOer Status of Dial Tone Detectors 1-4 o s idle 1 = busy 2 ~ busied-out Status of Tone Generator 0 ~Idle 1 a busy 2 ~ busied-out Page 111
PN 9104-091-12&-NA COMMAND 980- SYSTEM STATUS DISPLAY {CONT'D).
Pocket Reference Guide COMMAND 981 - INTER-DX LINK STATUS DISPLAY This command provides status Information on the Inter-OX chip connection links. Background: OX Chip 0 I 33-64 1 ss-96 I 1-32 OX Chip 2 OX Chip 1 ·- Links 1-32 connect chips 0 and 2. links 33-64 connect chips 0 and 1. Links SS-96 connect chips 0 and 1 or 0 and 2. Devices in slots 1 ami 2 use OX 0. Devices in slots 3,4.5 and 6 use OX 1. Devices In slots 7,8,9 and 10 use OX 2.
PN 9104-091-120-NA COMMAND 981 - tNTER-DX liNK STATUS DISPlAY (CONT'O) Register 1 Register Nu~er Inter-ox Link Number (01-96) Register 2 Register Number lnter-DX Link states 0: not In use 1 : In use Inter-OX link states are stored in bytes, so the display shows eight links at a time. The state of the Inter-OX Link actually reQuested identifies Itself by flashing.
Pocket Reference Guide COMMAND 982 - STATION STATUS DISPLAY Reglater 1 Register Nullber Station equipment number {001 -- 160} Register 2 Regi star NUI!lber Call Processing State {See Tabla 10-1) Cal I Processing Substate (See Table 10-2) Peripheral Processing State (for MITEL personnel only) Page 115
PN 9104-091-120-NA TABLE 10-1 CALL PROCESSING STATE CODES State Code Ot 02 03 04 05 05 07 08 09 OA OB oc 00 OE OF 10 11 12 Page 116 Idle Waiting for a Receiver Slgnellng Busy Reorder Camped on Held Welting for Answer Talk Message Waiting Calling Back Trunk Signaling Automatic Wake-up Announcement Message Register Audit Special Set Hard Hold SMOR Wake up Printer Queue
Pocket Reteren~:e Guide TABLE 10-2 CALL PROCESSING SUBSTATE CODES Code 14 15 16 19 1A 18 1C 10 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 28 2C 20 2E Substate Walt for Una Select (SUPERSET Telephone) Busy Override Swap/call Forward System Admlnlstrlltion Console Functions Direct Trunk Select Hold W Voice Indication Call Hold Pickup Super Functions Waiting lor DISA Access Code Behind PBX Special Substate Speed Call Set Up Manual Digits Into Speed Call Number Select Trunk Substate Add Held Trunk.
PN. 9104-091-120-NA COMMAND 982 - STATION STATUS DISPLAY (CONT'D) Register 3 Conference ~i r-c::u•1 Dial Tone Oe:te.;ao-r Inter-ox Link n'""bor ( l-961 Source Tone 10 -----l !l'
Pocket Reference Guida TABLE 10-3 SOURCE TONE TYPES Tone Type \D 00 01 QUIET 02 RING BACK DIAL TONE REORDER TRANSFER DIAL TONE STATION CAMP-ON TRUNK CAMP-ON DISCONNECT (not used) CAMPED-ON BUsY CALl FORWARD FOLLOW ME DIAL TONE EXECUTIVE BUSY OVERRIDE SIGNAL DIAl TONE PROMPT BEHIND PBX DIAL TONE AUTOMATIC WAKE-UP TONE 03 04 05 06 07 08 09 ,, 10 12 13 14 BUSY ------ ·--- -- ---- ---- Page 119
PN 9104-091-120-NA COMMAND 982- STATION STATUS DISPLAY (CONTD) Register 4 Soun:;e Osvijce Tv_pe IT.E,S,L,R,B,O,H, ?t Sourc11 Device Equ:i J)mlnt NII?Jbe r DeSiinolion Device Type IT.E.S,L.fi,B,O,H,?] T Trunk S C£N H li
Pocket Reference Gullfe COMMAND 982- STATION STATUS DISPLAY (CONT'D) Register 5 Reg! ster Nwmar Station Condition 0 ~ on-hook 1 • off-hook.
PN 9104-091-120-NA COMMAND 983 - SUPERSET STATUS DISPLAY Register 1 ~ Register~::: SUPERSET nuntle r J 00: no SUPERSET telephones in system 01-80: SUPERSET equipment number When this commend Is initially entered, it dls· plays the lowest SUPERSET 4" equipment number currently programmed.
Pocket Reference Guide COMMAND 983 - SUPERSET STATUS DISPLAY (CONT'Dl Register 3 [Jl'MF Rec~:~ivar ~ 1-5) Coni!it-ence c:i rcuit t \-61 Oi~l Tono Dotootor 11-41 lnn•-DX Link n..,b., (1-9S) - - - - - ' Source Tone 10 !Refer to Tobh 10-31-----...J C-odec: Function Control D' Normal Fi I tor/Codac Oporation 1' Digilal Loopbock Codsc Rac:ejve Fi I un Ga~n Codoc Transm;t fij.
PN 9104-091-120-~ COMMAND 913 - SUPERSET STATUS DISPUY (CONT'D) . Register 4 Source Olovi ce Type IT.E,S, L,l\,8,0,1'1, 71 Sour"e Device Equipnenl I'IIOI!ber Dest in:at ion Devic11 Type !T,E,S,L.R,B,O.H, ?I T Trunk E EKtenoion 1.. Trunk Group S CXW R Ring group 0 Opr !Conoolel 1 unknown B Ni ghl lie II H Hunt Group I' Peger Deot iMt ion Device Equipment Number lluKi I ierv De• ice Type IT,E,S,L,R,B,O.H.
Pocket Reference Guide COMMAND 984 - TRUNK STATUS DISPLAY Register 1 ~ Register Nu~er y Trunk equipment number 00 a no trunks in system Ol-80 ~trunk equipment number When this command Is initially entered, the lowest installed trunk equipment number Is displayed.
PN 9104-091-120-NA COMMAND 984 - TRUNK STATUS DISPLAY (CONT'O) Regls••r 3 Conference- circ::ui t Oi11l Tone Detector Inter-ox l-ink nlltlbor (1-S61 Soun,a Tone ID (Refer t~ T•bla 10-3) - - - - - - ' Codec 'Function Control 0; Nor.m;e:1 Filter/C-c;~dsc O,paratlon 1 ~ Oi gj tel Loopba~;k Cod.cc Receive Fi 1 ter Gain Cadee Trensmit Filter_Gain Page 126 0 ._ 7 {0 - Z: Analog 1-oo~baok 3 : PQWer Down -7 dBl - - - - - - - - - ' 0 - 7 CD- +7 dBl --------.
Pocket Reference Guide COMMAND 984- TRUNK STATUS DISPLAY (CONT'D) Register 4 Source DBvice Type IT, E,S,L.R,B,O,H,7) Source Device EquiJ~Mn' N.nber Des1ina1ign Device Type IT, E,S, L,R,B,O,H.7l T Truok StXJ\1 H Ht.m 1 Group £ R ? P E)( t-ens ion Ring group unkn""n Pogar L Trunk Group 0 Opr (ConsDiel B Nigh! !Ia II Oes.tin•1 ion Device Equipn'len.\ Nl.llrlbar .lluxi I ioty Device Typo IT, E.S.L,R.II,O,H. ?l AuJdliary Davie::& Equi:pmen.
f>N 1104-091-120-NA COMMAND 984 - TRUNK STATUS DISPLAY (CONT'DJ RegisterS Rl nglng Voltage o ~High amplitude AC detected on Tip & Ring External Ground (Message Registration) 0 • ncn grounded 1 = grounded Register 6 r-~~~~~--~-, Register Nurroer RESERVED - - - - ' Reverse Currenr Condition 0 • absent l = present {Tip more negative than Ring) Forward Cur rent Condl t ion 0 • absent 1 • present {from CO) Tip 0 1 r Page 121 Ground Condition------~ not grounded ,.
