User guide
Table Of Contents
- Software License Agreement
- Content
- Welcome
- IP Phone Keys
- Getting Started
- Methods of Customizing Your Phone
- Phone Status
- Customizing Your Phone
- Line and Call Appearances
- Presence Key
- Configuring Softkeys
- State-Based Softkeys
- Softkey Display Behavior
- Line Key
- Speed Dial Key
- Do Not Disturb (DND) Key
- Busy Lamp Field (BLF) Key
- BLF/List Key
- Automatic Call Distribution (ACD) Key (for Sylantro Call Managers)
- XML Key
- Flash Key
- Sprecode Key
- Park/Pickup Keys
- Call Forward Key
- BLF/Xfer
- Speed Dial/Xfer
- Speed Dial/Conf
- Directory Key
- Callers List Key
- Redial Key
- Conference Key
- Transfer Key
- Intercom Key
- Phone Lock Key
- Paging Key
- Empty Key
- None Key
- Making Calls
- Receiving Calls
- Handling Calls
- Managing Calls
- Additional Features
- Display DTMF Digits
- Play Call Waiting Tone
- Stuttered Dial Tone
- XML Beep Support
- Status Scroll Delay
- Switch UI Focus to Ringing Line
- Call Hold Reminder During Active Calls
- Call Hold Reminder (on single hold)
- Call Waiting Tone Period
- Goodbye Key Cancels Incoming Calls
- Message Waiting Indicator
- Incoming Intercom Call Features
- Group RTP Paging
- Shared Call Appearance (SCA) Call Bridging
- Star Codes
- Other Features
- Model M680i Expansion Module
- Troubleshooting Solutions
- Why is my display blank?
- Why is my speakerphone not working?
- Why can’t I get a dial tone?
- Why doesn’t my phone ring?
- Why is the light not coming on with a new voicemail message?
- Why is my handset not working?
- How do I find the IP address of my phone?
- Why does my phone display the No Service message?
- How do I change my user password?
- Why does my phone display Bad Encrypted Config?
- How do I restart the IP phone?
- How do I lock my phone?
- Limited Warranty
- Limited Warranty (Australia Only)
- Appendix A - Time Zone Codes
- Index
- Disclaimer
Configuring Softkeys
41-001524-00 REV00 – 04.2014 99
Using the Paging Key
The following procedure describes the use of the Paging key on the IP phone. The procedure assumes you have already
configured the Paging key using the Aastra Web UI.
9. In the Value field, enter a multicast IP address and a port number for the Paging key. When you press this key, the
phone initiates an outgoing multicast RTP session to the specified address using the specified port. (For example,
239.0.1.15:10000).
Notes:
1. When you select Paging for the Type field, the Line field is disabled.
2. The Value field allows for one multicast address entry only.
10.To receive RTP steams for group paging, you must also configure the Paging Listen Addresses parameter at the
path, Basic Settings > Preferences > Group Paging RTP Settings. For more information about setting this parameter,
see “Group RTP Paging” on page 160.
11. Click Save Settings to save your changes
Notes:
• The recipient of a paging call can set a global DND to ignore any incoming pages.
• For incoming paging, the phone uses the Intercom configuration settings. The incoming page is dependant on the
Allow Barge In parameter setting and the idling/on call state.
IP Phone UI
1. On the IP phone, press the softkey or expansion module key you configured for Paging.
The phone opens a multicast RTP session and an outgoing OR incoming phone screen displays.
2. Press the Drop key to end the multicast RTP session and return to the Home screen.
Note:
If you enable global DND on the phone, the incoming multicast RTP session is dropped.