User guide
Table Of Contents
- 11BRing/Message indicators
- 12BSelecting Menu Options
- 13BAbout Feature Access Codes
- 14BLine Interface Module
- 15BDon't cradle the handset!
- 16BProtect your hearing
- 17BAdjust the viewing angle
- 18BRinger Control
- 19BHandset Receiver Volume Control
- 20BSpeaker Volume Control
- 21BDisplay Contrast Control
- 22BFeature Keys
- 23BLanguage Change
- 24BMake a Call - PBX
- 25BMake an External Call - KTS
- 26BMake an Intercom Call - KTS
- 27BAnswer a call
- 28BRedial
- 29BSpeed Call Keys
- 30BSpeed Call – Personal
- 31BHandsfree Operation
- 32BAuto–Answer
- 33BGroup Listen
- 34BHold
- 35BHold and Page
- 36BMute
- 37BHandset Mute (does not work?)
- 38BTransfer
- 39BConference
- 40BConference Split (5324 IP Phone only)
- 41BAdd Held (5324 IP Phone only)
- 42BSwap
- 43BCall Forward
- 44BCall Forward - Remote (I am Here)
- 45BCall Forward - Forced
- 46BCall Forward - Toggle
- 47BMessaging - Advisory
- 48BMessaging - Callback
- 49BAccount Codes
- 50BCallback
- 51BCall Park
- 52BCall Park - System
- 53BCall Park - Specific Orbit
- 54BCall Park - Destination Phone
- 55BCall Pickup
- 56BCampon
- 57BDo Not Disturb
- 58BOverride
- 59BPaging - PA
- 60BPaging - Direct
- 61BHandsfree Answerback to a Direct Page
- 62BPaging - All Sets
- 63BPaging - Group
- 64BDirect Station Select/Busy Lamp Field (DSS/BLF)
- 65BDirect Station Select (DSS)/Busy Lamp Field (BLF)/Call Pickup
- 66BDirect Page/Busy Lamp Field (DP/BLF)
- 67BDirect Station Select (DSS)/Busy Lamp Field (BLF)/Direct Page/Call Pickup
- 68BHeadset Operation
- 69BMusic
- 70BPark and Page
- 71BRecord a Call
- 72BAuto-Latch Microphone
- 73BReminder
- 74BReminder - Multiple
- 75BCall Logging (5324 IP Phone only)
- 76BPhonebook
- 77BCall Monitoring
- 78BDoor Opener
- 79BNight Answer
- 80BDate and Time Setup
- 81BRelease
- 82B
- Secure Hot Swap
- 83BMobile Extension
- 84BTurn the conference unit on and off
- 85BAdjust the conference unit volume
- 86BPlace the conference unit in Presentation mode
- Mute the Conference Unit
- Exit the conference
- 89BTo start a Conference
- 90BAdjust the conference unit volume
- 91BMute the conference unit
- 92BExit the conference
- 93BLINE INTERFACE MODULE MODE
- 94BFAILOVER MODE
- 95BEMERGENCY CALLS
- 96BFEATURE ACCESS CODES
5312/5324 IP Phones User Guide
Swap
To call another party when you are in an established two–party call:
1. Press
( TRANS/CONF ).
2. Dial the number.
To alternate between the two parties:
• Press the Swap/Trade feature key or the Trade softkey.
Call Forward
Call Forward lets you redirect incoming calls to an alternate number.
"External Calls?" redirects your incoming external calls only; "Internal Calls?" redirects your incoming
internal calls only. If you want to redirect both external and internal calls, you must program each
separately.
"Always?" redirects all incoming calls regardless of the state of your telephone. "No Ans?" redirects
calls after several rings if you don't answer. "If Busy?" redirects calls when your telephone is busy.
"Busy/No Ans?" redirects calls when your telephone is busy or when you don't answer.
Note: For information about "I'm Here?", see Call Forward – Remote.
To program Call Forward:
1. Press
( MENU ).
2. Press # or the No softkey until "Call Forwarding?" appears.
3. Press * or the Yes softkey .
4. Press # or the No softkey or the Next softkey until the type of Call Forward that you want to set
up appears.
An asterisk next to the Call Forward option indicates that call forwarding is turned on.
5. On a 5324 IP Phone only, press * or the Review softkey.
6. If a number is already programmed, press * or the Change softkey .
7. Press * or the Program softkey .
8. Dial the destination number.
If you make an error while dialing, press * or the <— softkey to correct errors.
9. Press
( DOWN ) or the Save softkey.
10. Press
( MENU ) to exit.
15