Mitel PBX interface with Conferencing Server Configuration Notes Note: This document section is maintained by Mitel Networks When referring to any information in this document please also check the Additions & Correction section on the last page for updates.
Mitel PBX interface with Conferencing Server Configuration Notes Mitel PBX interface with Conferencing Server Configuration Notes ........................1 Introduction....................................................................................................................3 3300ICP with ISDN or SX2000 with ISDN...............................................................3 Example of T1 PRI programming on 3300 or SX2000...........................................
Introduction This document describes the configuration of Mitel Networks PBX’s to correctly interface to the Interactive Group Communication System by VCon. For more information on the configuration of the IGC, please refer to Mitel 3300 RemoteAbility IGC Integration Specifications V1. Note that all PBX configuration should be undertaken by a qualified Technician.
ANI/DNIS/ISDN Number Delivery Yes Link Descriptor Assignment Number: 4 Address for Message Control: A BER - Maintenance Limit, 10**-n: 4 BER - Service Limit, 10**-n: 3 Data Call Alternate Digit Inversion: Yes Framing Losses in 24 hrs - Maintenance Limit: 255 Framing Losses in 24 hrs - Service Limit: 9000 Integrated Digital Access: ISDN NODE Satellite Link Delay: No Slip Rate - Maintenance Limit (slips/24hr.): 5000 Slip Rate - Service Limit (slips/24hr.
MSDN-DPNSS-DASSII Trunk Circuit Descriptor Number Card Type 4 UNIVERSAL T1 Dual Seizure Priority Incoming Far End Connection Signalling Protocol Local Office MSDN-DPNSS Trunk Service Assignment Trunk Service Number: Release Link Trunk: Class of Service: Class of Restriction: Baud Rate: Intercept Number: Non-dial In Trunks Answer Point - Day: Non-dial In Trunks Answer Point - Night 1: Non-dial In Trunks Answer Point - Night 2: Dial In Trunks Incoming Digit Modification - Absorb: Dial In Trunks Incom
• • • • • Attach VCon IGC server T1 link to NSU, DSU or Embedded PRI card o Configure hardware for Line Termination through jumpers or DIP switch – please refer to the Technician’s Handbook of the correct product (3300 or SX2000) connect to server with a straight through cable Program trunks o for example, please see Example of T1/D4 Programming on 3300 or SX2000 Test link to server by dialing < # > e.g.
ANI/DNIS/ISDN Number Delivery Yes Link Descriptor Assignment Number: 4 Address for Message Control: BER - Maintenance Limit, 10**-n: 4 BER - Service Limit, 10**-n: 3 Data Call Alternate Digit Inversion: Yes Framing Losses in 24 hrs - Maintenance Limit: 255 Framing Losses in 24 hrs - Service Limit: 9000 Integrated Digital Access: T1D4 Satellite Link Delay: No Slip Rate - Maintenance Limit (slips/24hr.): 5000 Slip Rate - Service Limit (slips/24hr.): 7000 Alarm Debounce Timer - Service Limit (millisec.
Digital E and M Trunk Circuit Descriptor Assignment Number: Call Collision Handling: AT&T Call Collision Handling: Ignore Far End Disconnect: Release Acknowledge Timer: Address Signalling: Disconnect Timer: Incoming Start Type: Dial Tone on Incoming Seize: Outpulse Delay Timer: Outgoing Start Type: Supervision Timer: Maximum Wink Timer: Minimum Wink Timer: Guard Timer: Fake Answer Supervision After Outpulsing: Ignore Answer Supervision: Release Supervisio n Expected: Audio Inhibit Until Answer Supervision:
Digital Trunk Assignment Cabinet: Shelf: Slot: Circuit: Card Type: Trunk Number: Trunk Service Number: DTS Service Number: Circuit Descriptor Number: Interconnect Number: 6 1 1 1 UNIVERSAL T1 6101 4 4 1 Example of ARS Programming on 3300 ICP/SX2000 Create Trunk Group Trunk Group Assignment Trunk Group Number 3 Hunt Mode Trunk Group Busy RAD Maximum Network Hop Comments Terminal Analog TG 4 Circular Remoteabilty 5 Terminal To Sx2000 Add individual trunks to trunk group - all 23 ISDN trunks or
2 6102 3 6103 4 6104 5 6105 6 6106 7 6107 8 6108 9 6109 10 6110 7/4/2004 Page 10 of 22
Create Digit Modification Assignment - in this example, we are using Digit Modification number 4, and there are no digits to absorb or to insert Digit Modification Assignment Digit Number of Modification Digits to Number Absorb 1 3 2 0 3 1 4 0 5 0 Digits to be Inserted Final Tone Plan/Information Marker Create Route Assignment - in this example, we are using Route 4 Route Assignment Trunk Group Number Digits Before Outpulsing XNET Trunk Group Number 1 COR Group Number Digit Modifica
SX200 with ISDN • • • • • Attach VCon IGC server to PRI card with straight through cable o Configure hardware for Line Termination. Please refer to SX200 Technician’s Handbook for more information.
Example of T1 PRI Programming on SX200 Refer to SX200 EL/ML Technicians Handbook , Programming a PRI, for System Configuration, Class of Service Options and System Options/System Timers. Form 13 Assign T1 E&M circuit descriptor to the ISDN trunk.
7/4/2004 Page 14 of 22
7/4/2004 Page 15 of 22
Define the incoming ISDN trunk as a Dial In trunk in form 15 7/4/2004 Page 16 of 22
Assign the ISDN trunks to a trunk group in Form 16 7/4/2004 Page 17 of 22
Select a T1 Link Descriptor for the ISDN trunks in form 42 7/4/2004 Page 18 of 22
7/4/2004 Page 19 of 22
Assign the ISDN link descriptor to slot 6 and/or slot 8 on the PRI card bay, Form 43 Form 44, Network Sync - To be determined by qualified Technician SX200 with T1/D4 • • • Attach VCon IGC server to SX200 with cross over cable. Program trunks for T1/D4. All values are default.
T1 Crossover cable wiring Specifications [RJ45 Connector] Supplied with RemoteAbility system.
Addition & Corrections The change I had to make was with the ANI/DNIS insertion in digit mod with T1/D4 trunks: The doc says above to insert **6135922122** The correct format for this string is : *ANI*DNIS* We used this at for fixed ANI at Pyramid: *3125551212*7900* For caller's ANI: **7900* 7/4/2004 Page 22 of 22
