User's Manual

3
If you are connecting a handset, do not connect the power at this point. Proceed
with the following instructions:
Attaching the Bluetooth Handset and Charging Plate to
the 5330/5340/5360 IP Phone (See Figure )
• Disconnect the LAN power supply cable from the back of the phone if you
have not already done so. Detach the corded handset from the phone if
installed.
• Remove the cover on the front of the phone at the bottom of the handset
cradle by removing the retaining screw inserted from the back of the
phone. Keep the screw in a safe place—you must re-use this screw.
 Bring the new charging cover to the phone and plug the power jumper cable
into the connector in the phone.
 Insert the lip on the right side of the cover into the slot on the phone and
snap the cover into place.
 Using the same screw that you removed from the phone in an earlier step,
screw the cover to the back of the phone. Place the Bluetooth Handset in
the phone cradle.
 Reconnect to the power supply by plugging the LAN cable into the LAN port
on the back of the phone. Remember to thread the LAN plug through the slot
on the phone’s base unit, so that the base unit sits level.
NOTE: Mitel-supplied power adapters are the only adapters qualified by Mitel
for connection to the 5330/5340/5360 IP Phones.
 Pair the Bluetooth Handset with the Bluetooth Module:
(a)Ensure that the battery of the Bluetooth Handset is at least partially
charged.
(b)Press and hold down the pairing button on the back of the Bluetooth
Module for 5 seconds to activate telephone pairing mode. The LED on
the Bluetooth Module blinks. The Cordless Devices application opens
on the telephone and prompts you to “Press the pairing button on the
cordless device now”.
(c)Press and hold down the hookswitch on the Bluetooth Handset for 5
seconds to activate accessory pairing mode. The LED on the cordless
accessory blinks. After a moment, the Cordless Devices application
displays the protocol version, firmware version, and hardware version
for the cordless handset to be paired.
(d)Press Yes to confirm pairing. A Pairing Passcode window displays on
the IP Phone.
(e)Enter a valid passcode (default = 0000) using the dialpad (or keyboard
on the 5360 IP Phone). Press OK.
(f) The LED on the Bluetooth Module lights solid for 2 seconds then
resumes normal behavior. The Bluetooth Handset is paired to the
Bluetooth Module.
(g)Press OK to return to the Cordless Devices application. Press Close to
exit the application.
NOTE:
The Bluetooth Handset must be fully charged before use. This will typi-
cally take 3 hours. A new, fully-charged handset battery has a talk time of 6
hours.
Pairing a Bluetooth Headset Device
NOTE: 3rd-party Bluetooth headset devices do not physically attach to a 5330/
5340/5360 IP Phone, nor can they be powered by the phone. Follow the Blue-
tooth headset manufacturer’s instructions for pairing the device.
1. Ensure that the battery of the Bluetooth Headset Device is at least partially
charged.
2. Press and hold down the pairing button on the back of the Bluetooth Modle
for 5 seconds to activate telephone pairing mode. The LED on the Bluetooth
Module blinks. A prompt on the IP Phone displays to follow the manufactur-
er’s instructions for placing the Bluetooth headset in pairing mode. The pair-
ing process ends when the LED on the Bluetooth Module stops blinking.
3. The pairing confirmation window on the IP Phone appears, displaying the
product name for the device to be paired.
4. Press Yes to confirm pairing. A “Pairing Passcode” window displays on the
IP Phone.
5. Enter a valid passcode (default = 0000) using the dialpad (or keyboard on
the 5360 IP Phone). Press OK. An “Auto Connect” window displays on the
IP Phone.
6. Press Yes if the phone will not be shared with other users; press No if the
phone will be shared with other users and multiple headsets.
7. The LED on the Bluetooth Module lights solid for 2 seconds then resumes
normal behavior. The Bluetooth Headset Device is paired to the Bluetooth
Module.
8. Press OK to return to the Cordless Devices application. Press Close to exit
the application.
B