Use and Care Manual

ManualsBrandsMiTek ManualsBuilding Hardware2 in. x 2 in. x 6 in. G185 12-Gauge Angle

231

232

233

234

235

236

237

238

239

240

EWP Hangers

227

MiTek

Product Catalog

EWP Hangers

Top Mount Hanger Charts

Fastener Schedul

Uplif

DF/SP

Ref. No. Ga W H D L TF Type Qty Type LVL PSL LSL SPF DF/SP

160%

HBPH55925 HB5.50/9.25 x 10 5-1/2 9-1/4 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHXU55925

HWP5.37 H=9.25,

HWPH5.37 H=9.25

x 7 5-1/2 9-1/4 3-1/4 11-1/2 3 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH55925 HGLTV5.37 H=9.25 x 7 5-9/16 9-1/4 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

BPH5595 -- x 12 5-9/16 9-1/2 3 -- 2-5/32 4 6 16d 4 10d 3065 3065 3065 2340 -- 3065 850

HBPH5595 HB5.50/9.5 x 10 5-1/2 9-1/2 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHM5595 -- x 7/10 5-5/8 9-1/2 2-1/2 7 3 2 -- 16d 2 10d 3265 3265 3265 2480 -- 3265 --

PHXU5595

HWP5.37 H=9.5,

HWPH5.37 H=9.5

x 7 5-1/2 9-1/2 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH5595 HGLTV5.37 H=9.5 x 7 5-9/16 9-1/2 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

HBPH55112 HB5.50/11.25 x 10 5-1/2 11-1/4 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHXU55112

HWP5.37 H=11.25,

HWPH5.37 H=11.25

x 7 5-1/2 11-1/4 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH55112 HGLTV5.37 H=11.25 x 7 5-9/16 11-1/4 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

5-1/4 x 11-1/2 HLBH55115 -- x 7 5-9/16 11-1/2 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

BPH55118 -- x 12 5-9/16 11-7/8 3 -- 2-1/32 4 6 16d 6 10d 3050 3050 3050 2340 -- 3050 1275

HBPH55118 HB5.50/11.88 x 10 5-1/2 11-7/8 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHM55118 -- x 7/10 5-5/8 11-7/8 2-1/2 7 3 2 -- 16d 2 10d 3265 3265 3265 2480 -- 3265 --

PHXU55118

HWP5.37 H=11.875,

HWPH5.37 H=11.875

x 7 5-1/2 11-7/8 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH55118 HGLTV5.37 H=11.875 x 7 5-9/16 11-7/8 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

HBPH5512 -- x 10 5-1/2 12 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHXU5512 -- x 7 5-1/2 12 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910

4530

-- 5910 1120

HLBH5512 -- x 7 5-9/16 12 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

BPH5514 -- x 12 5-9/16 14 2-1/2 -- 2-1/32 4 6 16d 6 10d 3050 3050 3050 2340 -- 3050 1275

HBPH5514 HB5.50/14 x 10 5-1/2 14 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHM5514 -- x 7/10 5-5/8 14 2-1/2 7 3 2 -- 16d 2 10d 3265 3265 3265 2480 -- 3265 --

PHXU5514

HWP5.37 H=14,

HWPH5.37 H=14

x 7 5-1/2 14 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH5514 HGLTV5.37 H=14 x 7 5-9/16 14 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

BPH5516 -- x 12 5-9/16 16 2-1/2 -- 2-1/32 4 6 16d 6 10d 3050 3050 3050 2340 -- 3050 1275

HBPH5516 HB5.50/16 x 10 5-1/2 16 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHM5516 -- x 7/10 5-5/8 16 2-1/2 7 3 2 -- 16d 2 10d 3265 3265 3265 2480 -- 3265 --

PHXU5516

HWP5.37 H=16,

HWPH5.37 H=16

x 7 5-1/2 16 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910 4530 -- 5910 1120

HLBH5516 HGLTV5.37 H=16 x 7 5-9/16 16 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

BPH5518 -- x 12 5-9/16 18 2-1/2 -- 2-1/32 4 6 16d 6 10d 3050 3050 3050 2340 -- 3050 1275

HBPH5518 HB5.50/18 x 10 5-1/2 18 3-1/2 -- 3 6 16 16d 10 16d

6185 6185 6185 4910

6185

2705

PHM5518 -- x 7/10 5-5/8 18 2-1/2 7 3 2 -- 16d 2 10d 3265 3265 3265 2480 -- 3265 --

PHXU5518 HWPH5.37 H=18 x 7 5-1/2 18 3-1/4 11-1/2 2-1/2 4 4 16d 6 10d 5910 5910 5910

4530

-- 5910 1120

HLBH5518 HGLTV5.37 H=18 x 7 5-9/16 18 6 12 3-1/8 3 12 NA16D-RS 6 16d 10045 10045 10045 7680 -- 10045 1580

1) When I-joist is used as a header, all header nails must be 10d (0.148") x 1-1/2.

2) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted

3) Some listed loads may be increased for short-term loading. Refer to MiTek code evaluation reports for details.

4) When I-Joists with flanges less than 1-1/2" thick are used as headers, the reduction factor for 1-1/4" flange is 0.69 and 0.84 for 1-3/8" flange.

5) NAILS: 10d nails are 0.148" dia. x 3" long, NA16D-RS nails are 0.148" x 3-1/2" long, 16d nails are 0.162" dia. x 3-1/2" long.

Load tables address hanger/header/fastener limitations only. Joist limitations must be determined for each installation

New products or updated product information are designated in blue fon

5-1/4 x 11-7/8

5-1/4 x 9-1/2

Joist Size

(in)

Top

Qty

Face

Qty

5-1/4 x 14

5-1/4 x 12

MiTek USP

Stock No.

I-Joist

Code

Ref.

IBC,

FL,

5-1/4 x 18

5-1/4 x 16

Web

Stiff

Reqd

Allowable Loads Header Type (Lbs.)

1,3

Dimensions (in)

Header Joist Download 100%

5-1/4 x 9-1/4

5-1/4 x 11-1/4

Continued on next page