Use and Care Manual

218
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
EWP Hangers
BPH / HBPH Top Mount Hangers
These hangers are used to support LVL, LSL, and PSL beams
and headers in medium-to-heavy load conditions.
Materials: BPH – 12 gauge; HBPH – 10 gauge
Finish: G90 galvanizing
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• Refer to the top mount chart for applications requiring web stiffeners.
• Requirements for web stiffener from the I-Joist manufacturer should
be followed, even if web stiffeners are not required in MiTek literature.
• For welded installations, see page 325.
Typical BPH
installation
Typical HBPH
installation
BPH HBPH
Nailer Options
– chart represents maximum allowable loads for hangers used on wood nailers. Reference page 203.
Specialty Options Chart
– refer to Specialty Options pages 320 and 322 for additional details
Type Qty Type
2X 4 2 10d x 1-1/2 4 10d x 1-1/2 2080 230 1790 200
3X 4 4 16d x 2-1/2 4 10d x 1-1/2 2360 535 2030 460
(2) 2X 4 4 10d 4 10d x 1-1/2 2310 535 1985 460
4X 4 4 16d 4 10d x 1-1/2 2245 535 1930 460
2X 6 2 10d x 1-1/2 10 16d 2540 -- 2135 --
3X 6 6 16d x 2-1/2 10 10d 4500 -- 3780 --
(2) 2X 6 8 10d 10 16d 4140 1610 3480 1350
4X 6 10 16d 10 16d 5745 1610 4825 1350
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) Listed loads shall not be increased.
3)
Values in the table apply to standard top mount hangers without slope, skew or any other specialty options.
4)
NAILS:
10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long,
16d nails are 0.162" dia. x 3-1/2" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
New products or updated product information are designated in
blue font
.
HBPH
BPH
Uplift
1
160%
Uplift
1
160%
DF/SP
Allowable Loads (Lbs.)
2,3
S-P-F
Allowable Loads (Lbs.)
2,3
MiTek
Series
Nailer
Size
Fastener Schedule
4
Header Joist
Top
Qty
Face
Qty
Download
100%
Download
100%
Option
Skewed
1,3
Sloped Seat
2,3
Sloped / Skewed
1,2,3
Sloped Top Flange
4
Range 1˚ to 50˚ 1˚ to 45˚ See Sloped Seat and Skewed 0˚ to 45˚
1
)
Skewed han
g
ers with skews
g
reater than 15° ma
y
have all
j
oist nailin
g
on outside flan
g
e.
2
)
Slo
p
ed or slo
p
ed / skewed han
g
ers with slo
p
es
g
reater than 15° ma
y
have additional
j
oist nails.
3
)
For skewed han
g
ers, the re
q
uired cut t
yp
e
(
s
q
uare or bevel
)
of
j
oist member ma
y
var
y
based on skew an
g
le
and width of han
g
er. Some s
q
uare cut han
g
ers will re
q
uire custom
p
ricin
g
due to welded back
p
late.
4
)
Slo
p
ed to
p
flan
g
es with slo
p
es
g
reater than 15° ma
y
have additional header nails.
100% of table load
Add
SK , angle required,
right
(R) or left (L) , and
square cut
(SQ) or bevel cut (BV)
to product number.
Example: BPH3595_SK45R_SQ
Add
SL, slope required,
and up
(U) or down (D),
to product number.
Example:
BPH3595_SL30D
See Sloped Seat and Skewed.
Example:
BPH3595_SK45R_SQ_SL30D
Add
SF, angle required
and right
(R) or left (L),
to product number.
Example:
BPH3595_SF30L
Allowable
Loads
Ordering
100% of table load 100% of table load 100% of table load
H
W
D
TF
H
W
D
TF