Manualshelf

Use and Care Manual

ManualsBrandsMiTek ManualsBuilding Hardware2 in. x 2 in. x 6 in. G185 12-Gauge Angle
211212213214215216217218219220
EWP Hangers
211
MiTek
®
Product Catalog
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
EWP Hangers
I-Joist Charts Face Mount Hangers
Dimensions (in)
Ref. No. W H D A Qty Type Qty Type 100% 115% 125% 100% 115% 125%
IHFL15925 IUS1.56/9.5 -- 18 1-1/2 9-1/16 2-1/2 1-1/8 -- 8 10d -- -- 960 1095 1180 50 830 945 1020 40
Min 8 10d 1000 1120 1210 880 990 1065
Max 20 16d 2905 2905 2905 1815 1840 1860
IHFL15112 IUS1.56/11.88 -- 18 1-1/2 11-1/16 2-1/2 1-1/8 -- 10 10d -- -- 1200 1370 1475 50 1040 1185 1275 40
Min 10 10d 1250 1405 1515 1100 1235 1330
Max 24 16d 3065 3095 3115 1815 1840 1860
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 3065 3095 3115 1815 1840 1860
Min 8 10d 2 1000 1120 1210 880 990 1065
Max 20 16d 2 2905 2905 2905 1945 1975 1995
Min 10 10d 1250 1405 1515 1100 1235 1330
Max 24 16d 3295 3325 3350 1945 1975 1995
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 3295 3325 3350 1945 1975 1995
IHFL17925 IUS1.81/9.5 -- 18 1-3/4 8-15/16 2-1/2 1-1/8 -- 8 10d -- -- 960 1095 1180 50 830 945 1020 40
Min 8 10d 1000 1120 1210 880 990 1065
Max 20 16d 2905 2905 2905 2080 2105 2125
IHFL17112 IUS1.81/11.88 -- 18 1-3/4 10-15/16 2-1/2 1-1/8 -- 10 10d -- -- 1200 1370 1475 50 1040 1185 1275 40
Min 10 10d 1250 1405 1515 1100 1235 1330
Max 24 16d 3530 3560 3585 2080 2105 2125
Min 12 1440 1640 1770 1245 1420 1530
Max 14 1680 1915 2065 1455 1660 1785
Min 12 10d 1500 1685 1815 330 1320 1480 1595 260
Max 28 16d 3530 3560 3585 330 2080 2105 2125 260
Min 14 1680 1915 2065 1455 1660 1785
Max 16 1920 2190 2360 1660 1895 2040
Min 14 10d 1750 1965 2120 1540 1730 1865
Max 30 16d 3530 3560 3585 2080 2105 2125
IHFL20925 IUS2.06/9.5 -- 18 2-1/16 8-3/4 2-1/2 1-1/8 -- 8 10d -- -- 960 1095 1180 50 830 945 1020 40
Min 8 10d 1000 1120 1210 880 990 1065
Max 20 16d 2905 2905 2905 2410 2440 2460
IHFL20112 IUS2.06/11.88 -- 18 2-1/16 11-5/16 2-1/2 1-1/8 -- 10 10d -- -- 1200 1370 1475 50 1040 1185 1275 40
Min 10 10d 1250 1405 1515 1100 1235 1330
Max 24 16d 3530 3960 3960 2410 2440 2460
Min 12 1440 1640 1770 1245 1420 1530
Max 14 1680 1915 2065 1455 1660 1785
Min 12 10d 1500 1685 1815 1320 1480 1595
Max 28 16d 4115 4150 4170 2410 2440 2460
Min 14 1680 1915 2065 1455 1660 1785
Max 16 1920 2190 2360 1660 1895 2040
IHFL23925 IUS2.37/9.5 -- 18 2-5/16 9-3/16 2-1/2 1-1/8 -- 8 10d -- -- 960 1095 1180 50 830 945 1020 40
Min 10 10d 1250 1375 1375 1085 1085 1085
Max 24 16d 3530 4000 4320 2675 2705 2725
1) Uplift loads have been increased 60% for wind or seismic loads; no further increase shall be permitted.
2) IHFL (18GA) ─ install (2) 10d (0.148") x 1-1/2" nails through diamond dimple holes into the bottom chord of I-Joist member for a total uplift of 220 lbs.
IHF (16GA) ─ uplift capacity for hangers installed without joist nails is 65 lbs.
3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
Load tables address hanger/header/fastener limitations only. Joist limitations must be determined for each installation.
New products or updated product information are designated in blue font.
Code
Ref.
330
330 260
1-5/8 11 2-1/2 2
Joist Size
(in)
Uplift
1,2
160%
Uplift
1,2
160%
IHF16112
1-1/2 x
9-1/4 - 9-1/2
1-1/2 x
11-1/4 - 11-7/8
1-1/2 x 14
1-5/8 x
9-1/4 - 9-1/2
260
10d x 1-1/2
10d x 1-1/22
10d x 1-1/2 330
1-1/8
1-1/8
1-3/4 x 16
-- -- 16
2 - 2-1/8 x 9-1/2
2 - 2-1/8 x
11-7/8
2 - 2-1/8 x 14
1-5/8 x
11-1/4 - 12
S-P-F Header
Allowable Loads (Lbs.)
MiTek USP
Stock No.
Joist
2
Web
Stiff
Reqd Ga
Header
Fastener Schedule
3
Min/
Max
DF/SP Header
Allowable Loads (Lbs.)
MIU1.56/9 -- 16 1-1/2 9-1/16 2-1/2 2
1-5/8 x 14
1-3/4 x
9-1/4 - 9-1/2
1-3/4 x 11-7/8
1-3/4 x 14
10d x 1-1/22
260
330 260
IHF15925
IHF15112
IHF1514
IHF16925
10d x 1-1/2
9 2-1/2-- --
MIU1.56/11 -- 16 1-1/2 11-1/16 2-1/2
IHF1614 -- -- 16 1-5/8 13-7/16 2-1/2 2 10d x 1-1/2 330
-- -- 16 1-1/2 13-1/2 2-1/2
16 1-5/8
1-1/8
1-1/8
1-1/8
1-1/8
10d x 1-1/2
330
IHFL1714 IUS1.81/14 -- 18 1-3/4 13-3/8 2-1/2 -- -- 50
IHF17112 MIU1.81/11 -- 16 1-3/4 10-15/16 2-1/2 2 10d x 1-1/2
50
IHF1716 MIU1.81/16 -- 16 1-13/16 15-3/4 2-1/2 2 10d x 1-1/2 330
10d x 1-1/2
IHFL1716 IUS1.81/16 -- 18 1-3/4 15-7/8 2-1/2 -- --
1-1/8
2
10d
IHF20112 MIU2.1/11 2-1/2
IHF20925 -- -- 16 2-1/16 8-7/8 2-1/2 2
IHFL2014 IUS2.06/14 -- 18 2-1/16 13-3/16 2-1/2 --
1-1/8
1-1/8
--
IHF2014 -- -- 16 2-1/16 13-1/4 2-1/2 2 10d x 1-1/2
1-1/8
1-1/8
IHF17925 MIU1.81/9 -- 16 1-3/4 8-15/16
10d
10d
2
IHF1714 MIU1.81/14 -- 16 1-3/4 13-3/8 2-1/2 2
2-1/2 1-1/8
1-1/8
1-1/8
1-1/8
1-1/8
260
260
260
40
260
IBC,
FL,
LA
-- 16 2-1/16 11-3/16
10d x 1-1/2
260
330
330
330
260
260
260
40
40
330
330
50
10d x 1-1/2
10d 40
26033022-1/2 10d x 1-1/2 MIU2.37/9 -- 16 2-5/16 9-3/16
-- -- 501-1/8
1-1/8
IHFL2016 IUS2.06/16 -- 18 2-1/16 15-11/16 2-1/2
2-5/16 x 9-1/2
IHF23925
2 - 2-1/8 x 16
Continued on next page
H
W
D
A