Use and Care Manual

Lumber Hangers
141
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Lumber Hangers
MiTek
®
Product Catalog
HD Heavy-Duty Face Mount Hangers
HD hangers are heavy-duty face mount
hangers utilizing round and diamond holes to
achieve design exibility and maximum loads
for use with headers, joists, and trusses.
Materials: 14 gauge
Finish: G90 galvanizing
Options: See chart for Corrosion Finish
Options. All nominal lumber sizes are
available rough/full size lumber. See
Specialty Options Chart
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product
Notes, page 18.
• Min Nailing – Fill all round nail holes.
• Max Nailing – Fill all round and diamond nail holes.
• 16d sinkers (0.148" dia. x 3-1/4" long) may be used at
0.84 of the table load where 16d commons are specied.
Option
Skewed
1,3
Sloped Seat
2,3
Sloped / Skewed
1,2,3
Inverted Flange
1) Skewed hangers with skews greater than 15° may have all joist nailing on outside flange.
2) Sloped or sloped / skewed hangers with slopes greater than 15° may have additional joist nails.
3) For skewed hangers, the required cut type (square or bevel) of joist member may vary based on skew angle
and width of hanger. Some square cut hangers will require custom pricing due to welded back plate.
4) HD option hangers may be manufactured as welded products to achieve listed loads. Welded products have a primer interior finish.
Range
Allowable
Loads
See Sloped Seat and
Skewed
100% of table load.
75% of uplift load on
skews greater than 15˚.
100% of table load.
65% of table load when
nailing into the support
members end grain.
1˚ to 67-1/2˚
when width is 1-3/4" or less.
1˚ to 50˚ on all others.
2-1/4" widths or greater
(Widths < 2-1/4" may be
available as a Custom, contact
MiTek)
100% of table load
1˚ to 45˚
80% of table load.
75% of uplift load on
skews greater than 15˚.
Ordering
Add
IF,
to product number.
Example: HD410_IF
Add
SK, angle required,
right
(R) or left (L), and
square cut
(SQ) or bevel cut (BV)
to product number.
Example: HD410_SK45R_SQ
Add
SL, slope required,
and up
(U) or down (D),
to product number.
Example: HD410_SL30D
See Sloped Seat
and Skewed
Example:
HD410_SK45R_SQ_SL30D
HD610
Typical HD3212
glulam installation
Typical HDQIF
inverted ange installation
Typical HD210-2IF
inverted ange installation
HDQIF
HD51135
Typical HD610
installation
Typical HD210-2
installation
Specialty Options Chart
Refer to Specialty Options pages 320-321 for additional details.
HDQIF inverted ange hangers install with wood screws
eliminating the need to drill bolt holes, simplifying installation.
Materials: 14 gauge
Finish: G90 galvanizing
Options: See chart for Corrosion Finish Options
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• MiTek’s WS15 (1/4" dia. x 1-1/2" long) and WS3 (1/4" dia. x 3" long)
structural wood screws are supplied with HDQIF hangers.
HDQIF Inverted Flange Face Mount Hangers
H
A
W
D
H
A
3"
W
A
H
D
W
additional
diamond holes
for max nailing
standard round
holes for
min nailing