Use and Care Manual
115
Copyright © 2020 MiTek Industries, Inc. All Rights Reserved
Angles & Straps
Angles & Straps
MiTek
®
Product Catalog
F2
The ANJ44S is a 7 gauge heavy duty angle intended to securely
attach a post and beam together.
Materials: 7 gauge
Finish: Hot-dip galvanized
Installation:
• Install with (2) 1/2" x 2-1/2" HDG lag screws into each leg.
ANJ44S-HDG
Typical ANJ44S-HDG installation
ANJ Heavy Angles
Ref. No. W H L Qty Qty 100% 115% 125%
ANJ44S-HDG -- 7 3-1/2 4 4 2 1/2" HDG 2 1/2" HDG 510 585 640 --
1) Loads based on use of (2) 1/2" x 2-1/2" lag screws, loaded parallel to grain, in Douglas Fir-Larch (G=0.50).
Code
Ref.
Dimensions (in)
MiTek USP
Stock No.
Steel
Gauge
Header Joist
Fastener Schedule
1
DF/SP
Allowable Loads (Lbs.)
F2
Lag
Screw
Lag
Screw
Corrosion
Finish
4"
4"
3-1/2"
SCA Stair Angles
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
Typical SCA9-TZ
installation
SCA9-TZ
Typical SCA10-TZ
installation
Stair angles simplify stair construction. There is no need to calculate and
notch stair stringers. Stronger and safer than wood blocking, and the angle
and fasteners are hidden from view.
Materials: 12 gauge
Finish: G-185 galvanizing
Codes: IBC, FL, LA
Installation:
• Use all specied fasteners. See Product Notes, page 18.
• MiTek WS15-EXT (1/4" dia. x 1-1/2" long) structural wood screws are not
supplied with SCA angles.
• Use the SCA9-TZ for single 2x10 stair treads. Use the SCA10-TZ for double
2 x 6 stair treads.
• To calculate stair construction do the following:
1. Find the number of steps needed by dividing the vertical drop in inches from
the deck surface to grade by 7. Round off to the nearest whole number.
(Ex: Vertical drop of 39" divided by 7" equals 5.57 rounded off is 6)
2. Find the step rise by dividing the vertical drop by the number of steps
(39" divided by 6 = 6.5")
3. Find the step run by measuring the depth of your tread board
(Ex: (2) 2x6s with 1/4" gap will have a run of 11-1⁄4")
4. Find the stairway span by multiplying the run by the number of treads
minus one (Ex: 11-1⁄4" x 5 = 56-1⁄4")
• Using the above calculations, mark stair angle locations on each stringer.
Attach a stair angle to the inside of each stringer at the marked locations.
Attach stringers to deck rim joist and railing posts. Position tread-boards
on angles and fasten from below.
Ref. No. Qty Type Download 100%
SCA9-TZ TA9Z 12 9 6 WS15-EXT
445
SCA10-TZ TA10Z 12 10 8 WS15-EXT
595
1) Loads assume rise over run of 7/11.
2) MiTek's WS15-EXT structural wood screws are 1/4" dia. x 1-1/2" long and are not included with SCA angles.
3) HDG lag screws may be substituted for specified MiTek WS15-EXT structural wood screws with no load reduction.
New products or updated product information are designated in
blue font
.
IBC,
FL, LA
Code
Ref.
MiTek USP
Stock No.
Steel
Gauge
L
(in)
Corrosion
Finish
DF/SP
Allowable Loads (Lbs.)
1
Fastener
Schedule
2,3
Corrosion Finish
Stainless Steel Gold Coat
HDG Triple Zinc
Corrosion Finish Stainless Steel Gold Coat HDG Triple Zinc
Corrosion
Finish
Stainless Steel
Gold Coat
HDG
Triple Zinc
L
1-3/8"
1-3/8"