ADPRO® FastTrace™ 2 Series Hardware Installation Manual March 2015 Doc. 21790_05 Firmware version XOa 3.00.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Disclaimer The contents of this document are provided on an "as is" basis. No representation or warranty (either express or implied) is made as to the completeness, accuracy or reliability of the contents of this document. The manufacturer reserves the right to change designs or specifications without obligation and without further notice.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Trade Name Statement ADPRO is a registered trademark of Xtralis Pty Ltd. Contact Us UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 Middle East +962 6 588 5622 Asia +86 21 5240 0077 The Americas +1 781 740 2223 Australia and New Zealand +61 3 9936 7000 www.xtralis.com Environmental Information The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end of life.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Contents 1 Technical Specifications ...................................................................................................................... 9 2 Specific FastTrace Configurations ....................................................................................................12 2.1 FastTrace 2 Lite .........................................................................................................................12 2.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 8 Main and Extension I/O Cards ............................................................................................................48 8.1 Features .....................................................................................................................................48 8.2 Possible Configurations ...........................................................................................................48 8.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 12 Ethernet Card .......................................................................................................................................78 12.1 Installation .................................................................................................................................78 12.2 Ethernet Settings ......................................................................................................................
Hardware Installation Manual 8 ADPRO® FastTrace™ 2 Series 21790_05
ADPRO® FastTrace™ 2 Series 1 Hardware Installation Manual Technical Specifications The FastTrace 2 unit is the current video security system within the ADPRO ® FastTrace™ series. It has been developed as a high performance video security unit that can either be managed by CMS software (e.g. M3000) or by the ADPRO XOa client. Operating system PC platform – Linux OS Network protocols TCP, UDP, FTP, Telnet, HTTP, SMTP, RTSP, RTP Bandwidth Remotely adjustable: compression, fps, and quality.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Video output VGA connector; adjustable resolution (up to SXGA) With MiTAC PH10LU motherboard: DVI-I or DP (DisplayPort) Video compression H.264 Audio compression The audio compression depends on the camera type. Bandwidth Remotely adjustable: compression, fps, and quality. You can specify a bandwidth limit. Bandwidth consumption 6 fps CIF/SIF: 70 kbps 12 fps 4CIF/SIF: 400 kbps in optimal quality Recording type Continuous, on event (e.g.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Multi-site FastTrace 2 configuration is possible: Integration of up to 10,000 FastTrace 2 video security systems Remote video and audio, live video, and consultation of recordings Compatible with FOXnet®Plus, FALCONnet, S3100, Presidium, VSKwin®, VCP, and M3000 SDK for third-party integration Note Please use the reference numbers in this document (for example #17434080) for ordering parts with Xtralis, or for identifying the correct re
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 2 Specific FastTrace Configurations 2.1 FastTrace 2 Lite The FastTrace 2 Lite has been designed, developed and manufactured as a complete FastTrace 2 video security system, but the Entry system license that is included, limits the number of supported cameras to a maximum of 4 analogue cameras. Also note that the FastTrace 2 Lite can only operate with analogue cameras; it does not support IP cameras.
ADPRO® FastTrace™ 2 Series 2.3 Hardware Installation Manual FastTrace 2E The FastTrace 2E is the latest hardware in the ADPRO® FastTrace™ 2 series. It has been developed as a powerful video system with high performance and more efficient operation to replace the former FastTrace units. The FastTrace 2E has up to 20 analogue video inputs, up to 32 IP video inputs, and supports up to 32 analytic channels.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series FastTrace 2 video system). For more information on uploading licenses, see the XOa Client Software User Manual. Note The system license is locked on the FastTrace 2 motherboard and is therefore system specific: the license must include the correct MAC address. When you upload the system license and your unit already has other licenses (e.g.
ADPRO® FastTrace™ 2 Series 3 Hard Disks 3.1 Required Hard Disk Capacity Hardware Installation Manual As there are lots of configuration possibilities, Xtralis has a hard disk space calculator available. You can find this hard disk space calculator on the CD/DVD provided with your FastTrace 2 video system, or you can download it from our website www.xtralissecurity.com. Make sure you log on with sufficient download rights. Note The calculator is an estimating tool only. Figures are purely indicative.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual The screen displays the following information: Device Indicates the specific hard disk Power status The power status column displays one of the following statuses: Smart status ERROR there is a problem retrieving the power status of the drive ACTIVE/IDLE drive operates normally STANDBY drive is in low power mode (drive is in spin-down status) SLEEPING drive is in lowest power mode (drive is completely shut down) The smart status
ADPRO® FastTrace™ 2 Series 3.4 Hardware Installation Manual Material List (for 1 Hard Disk) Part Amount+ Reference Number A Support for disk 2 1 x #1729121* B Support for disk 3 and 4 1 x #1729122* C Disk screws 4 x #17434080 or #17434060 D Dented washers M4 4 x #17720050 E Mounting screws 4 x #17439080 SATA cable 1 x #1652087* Tie-wraps 1 x #17730220 3.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 2. Fix the second disk to the support #1729121* with the screws #17434080 or #17434060 and dented washers M4 #17720050. 3. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the left side of the casing. 4. Connect the disk to the SATA2 connector on the motherboard with the SATA cable (#1652087*). 5.
ADPRO® FastTrace™ 2 Series 7. Hardware Installation Manual Fix the third disk on the top side of the support for disk 3 and 4. If necessary, fix the fourth disk on the bottom side of the same support. Note Make sure to install the disk on the top side of the support first. 8. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the right side of the casing. 9. 10. Connect disk 3 to the eSATA4 connector on the motherboard with a SATA cable (#1652087*).
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 12. If the SATA cables do not have a locking mechanism, use tie-wraps to secure the cables on the disk(s) in the following way: 13. If there are unused cables left, bundle them with tie-wraps. 14. Fix the front plate (#17011610) on the base with the screws (#17444080). Put the cover in place and secure with 10 screws (#17439080). Connect a monitor/screen and keyboard to the server.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual You can now see the mounting holes for the disk bays: 2. Fix the second disk to the support #1729121* with the screws #17434080 or #17434060 and dented washers M4 #17720050. 3. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the left side of the casing. 4. Connect the disk to the SATA2 connector on the motherboard with the SATA cable (#1652087*). 5.
Hardware Installation Manual 7. ADPRO® FastTrace™ 2 Series Fix the third disk on the top side of the support for disk 3 and 4. If necessary, fix the fourth disk on the bottom side of the same support. Note Make sure to install the disk on the top side of the support first. 8. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the right side of the casing. 9. 10. Connect disk 3 to the SATA3 connector on the motherboard with a SATA cable (#1652087*).
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 12. If the SATA cables do not have a locking mechanism, use tie-wraps to secure the cables on the disk(s) in the following way: 13. If there are unused cables left, bundle them with tie-wraps. 14. Fix the front plate (#1701164x or #1701166x) on the base with the screws (#17444080). Put the cover in place and secure with 10 screws (#17439080). Connect a monitor/screen and keyboard to the FastTrace 2 server.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series If the cables connections are different, proceed as follows: 1. 2. 3. 4. 5. 6. 7. 8. Change the cable connections as described in the table. Adjust the boot order in the BIOS. To do so, follow the steps below. Switch off the power supply to the server. Connect a monitor/screen and keyboard to the server. Switch on the power supply and press F2 to enter BIOS mode. Choose Boot, and then choose Boot Drive Order.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 3. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the left side of the casing. 4. Connect the disk to the SATA2 connector on the motherboard with the SATA cable (#1652087*). 5. For the power supply to the disk, connect the remaining SATA power connector on the power cable of disk 1 (not the one on the tail end; that one is reserved for the D.O.M.) to the disk.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 8. Fix the support to the casing with 4 screws (#17439080): 2 at the front, and 2 at the right side of the casing. 9. 10. Connect disk 3 to the SATA3 connector on the motherboard with a SATA cable (#1652087*). If necessary, connect disk 4 to the SATA4 connector on the motherboard with a SATA cable (#1652087*). Caution! Do not bend the SATA cables too sharply to prevent cable damage. 11. 12.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 13. If there are unused cables left, bundle them with tie-wraps. 14. Fix the front plate (#1701164x or #1701166x) on the base with the screws (#17444080). Put the cover in place and secure with 10 screws (#17439080). Connect a monitor/screen and keyboard to the FastTrace 2 server. Switch on the power supply and wait for the boot window to appear. Select XOa Installer and press Enter.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 3.9.2 Activating RAID 1 RAID 1 requires a minimum of 2 hard disks. The size of the RAID 1 recording combination is the smaller of the 2 disks installed in your server. If, for example, you have a 1 TB disk and a 2 TB disk, the RAID 1 recording disk has a 1 TB capacity. Caution! When you apply RAID 1, the system formats the selected disks and erases the data on the disks. You will lose all the data on the disks.
ADPRO® FastTrace™ 2 Series 4 Hardware Installation Manual Fan Speed Selection Two large fans dissipate the heat. The fans have a switch to select the speed: low, medium, or fast. For most ambient temperatures, you can set the fan speed to medium. Change the fan speed only for extreme ambient temperatures. Note The most recent units are equipped with new models of fans. These models have no switch to select the speed. The speed is adjusted automatically.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 5 Front LED Indicators 5.1 Overview There are 3 LEDs on the front of the server: Green LED Power is on Yellow LED Fault Blue LED Storage media activity If the yellow LED lights up, check the status of your server. For more information, see the XOa Client Software User Manual. Caution! When the 3 LEDs are flashing simultaneously, the system is busy updating the recording disks. In that case, do not turn off power. 5.
ADPRO® FastTrace™ 2 Series 5.3 Hardware Installation Manual LED Connections with Main I/O Card In a system with a Main I/O card, the LED board is connected to the Main I/O card.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 6 Required Motherboard 6.1 Overview The FastTrace 2 video system only operates with an Intel DG31PR, Intel DG41TY, Intel DH55TC, Intel DH61BE, or MiTAC PH10LU motherboard. Intel DG31PR motherboard Intel DG41TY motherboard Intel DH55TC motherboard Intel DH61BE motherboard MiTAC PH10LU motherboard 6.2 BIOS Settings 6.2.1 Intel DG31PR or Intel DG41TY Motherboard Choose Main > System Time to set the system time.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Choose Advanced > Event log > Event logging and select the option Disable. Choose Advanced > Chipset Configuration > HPET and select the option Disable. Choose Power > After Power Failure and select the option Power-On. Choose Exit > Exit & Save Changes and select the option Yes. All other parameters can be left to the default settings. 6.2.3 Intel DH61BE Motherboard Choose Main > System Time to set the system time.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 7 Extension Boards 7.1 Overview Type Description HIPI PCI Express extension board for 8 IP cameras. (Not compatible with MiTAC PH10LU motherboard) See also technical datasheet 19531930 – HIPI card. Ethernet For FastTrace 2E only: Ethernet connection for IP camera network up to 32 IP cameras. An Ethernet card is not required with the MiTAC PH10LU motherboard.
ADPRO® FastTrace™ 2 Series 7.2 Hardware Installation Manual General Rules The FastTrace 2 video system offers 6 extension slots: On Intel DG31PR and Intel DG41TY motherboards: two PCI Express slots, two PCI slots, and two physical slots. On Intel DH55TC and Intel DH61BE motherboards: three PCI Express slots, one PCI slot, and two physical slots. On the MiTAC PH10LU motherboard: four PCI Express slots, and two physical slots. You can insert a HIPI card only in a PCI Express slot.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Slot Type Accepts 2 PCI Express Main I/O Extension I/O HIPI (ETH1) for 8 IP cameras 3 PCI Main I/O Extension I/O A/V with 4 or 8 channels (lowest camera numbers: CAM 1 > 4/8) 4 PCI Main I/O Extension I/O A/V with 4 or 8 channels (highest camera numbers: CAM 5/9 > 8/16) 5 / Extension I/O 6 / Main I/O 7.3.1.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Hybrid (16 Channels) Slot Type Extension Card 1 PCI Express HIPI (ETH1) 2 PCI Express Extension I/O 2 3 PCI Main I/O 2 4 PCI A/V 8 channels 1 5 / Extension I/O 1 6 / Main I/O 1 7.3.2 With Intel DG41TY Motherboard 7.3.2.1 Network/Monitor/Keyboard Note You must restart the XOa client software after connecting devices to a USB port. USB input 1 (/dev/ttyU1) is reserved for an external modem. 7.3.2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Slot Type Accepts 4 PCI Main I/O Extension I/O A/V with 4 or 8 channels (highest camera numbers: CAM 5/9 > 8/16) 5 / Extension I/O 6 / Main I/O 7.3.2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 7.3.3 With Intel DH55TC Motherboard 7.3.3.1 Network/Monitor/Keyboard Note You must restart the XOa client software after connecting devices to a USB port. USB input 1 (/dev/ttyU1) is reserved for an external modem. 7.3.3.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Example: camera numbers 1–4 allocated to the 4CH A/V card, and numbers 5–12 allocated to the 8CH A/V card. Note Only the A/V cards type DS42xx are allowed on the Intel DH55TC motherboard. 7.3.3.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual IP Cameras (8 or 16 Channels) Slot Type Extension Card 1 PCI Express HIPI (ETH1) 2 PCI Express HIPI (ETH2) 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 Hybrid (12 Channels) Slot Type Extension Card 1 PCI Express HIPI (ETH1) 2 PCI Express Extension I/O 2 3 PCI Express A/V 4 channels 1 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 Hybrid (16 Channels) Slot Type Exten
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 7.3.4.1 Network/Monitor/Keyboard Note You must restart the XOa client software after connecting devices to a USB port. USB input 1 (/dev/ttyU1) is reserved for an external modem. 7.3.4.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Slot Type Extension Card 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 Analogue Cameras (8 Channels) Slot Type Extension Card 1 PCI Express A/V 8 channels 1 (DS42xx) 2 PCI Express 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 Analogue Cameras (12 Channels) Slot Type Extension Card 1 PCI Express A/V 4 channels 1 (DS42xx) 2 PCI Express A/V
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Hybrid (12 Channels with 1 HIPI Card) Slot Type Extension Card 1 PCI Express A/V 4 channels 1 2 PCI Express HIPI (ETH1) 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 Hybrid (16 Channels with 1 HIPI Card) Slot Type Extension Card 1 PCI Express A/V 8 channels 1 2 PCI Express HIPI (ETH1) 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 7.3.4.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Slot Type Extension Card 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 If you want to use a second Extension I/O card, you have to replace either the Ethernet card or one of the analogue video cards in the PCI Express slots.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Hybrid (up to 32 Channels* with 1 Ethernet Card) Slot Type Extension Card 1 PCI Express A/V 4 or A/V 8 or A/V 16 channels 2 PCI Express Ethernet Card 3 PCI Express Extension I/O 2 4 PCI Main I/O 2 5 / Extension I/O 1 6 / Main I/O 1 (*) You can purchase IP camera licenses individually or in sets of 4. Depending on the license(s) you have purchased, you will have 1-32 video channels available.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 7.3.5.
Hardware Installation Manual 8 Main and Extension I/O Cards 8.1 Features ADPRO® FastTrace™ 2 Series Note With the FastTrace 2E Series, Xtralis introduced the Next Generation I/O cards. If you are using Next Generation cards with your FastTrace 2E unit, see Main and Extension I/O Cards Next Generation on page 57. The Main I/O (MIO) and Extension I/O (EIO) cards are internal I/O cards, to be fitted inside the ADPRO FastTrace 2 system. They are also called OTB (on-the-board) cards.
ADPRO® FastTrace™ 2 Series 8.3 Hardware Installation Manual Ordering Information Use these reference numbers to place your order with Xtralis: Item Reference Number Main I/O card 39544070 Main I/O card plus mounting set 39544000 Extension I/O card 39544080 Extension I/O card plus mounting set 39544010 8.4 Physical Position Insert the first set of I/O cards in the two furthermost slots (= nearest to the power supply). Use the L-shaped brackets to fix the cards to the chassis.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 8.5 Settings on the Main I/O Card If you are connecting PTZ cameras from the same RS-485 bus to multiple FastTrace 2 servers, set the RS-485 PTZ jumper on the Main I/O card to the 2-wire (PTZ) position. RS-485 cable length: max. 1200 m.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 3. Remove the two cables that connect the LED board on the front to the motherboard. The LEDs will be powered from the Main I/O card (of the 1st set). 4. Before inserting the Main I/O card into the motherboard, connect all necessary cables to the card. See the table below for an overview of cable connections. 5. 6.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual DG41TY motherboard A AUDIO (to MIO card), use adapter #16500660 B USB (to MIO card) C Reset (to MIO card) DH55TC motherboard 52 A AUDIO (to MIO card) B USB (to MIO card) C Reset (to MIO card) 21790_05
ADPRO® FastTrace™ 2 Series Hardware Installation Manual DH61BE motherboard A AUDIO (to MIO card) B USB (to MIO card), use adapter #16500660 C Reset (to MIO card) PH10LU motherboard 8.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Note Check the polarity! If you reverse the connection, the motherboard receives a permanent reset signal. 8.8 Adding an Extension I/O Card 8.8.1 Settings on the Extension I/O Card A From Main I/O card (#21760300) B Jumper setting: normally open relay contact C Jumper setting: normally closed relay contact 8.8.
ADPRO® FastTrace™ 2 Series 8.9 Hardware Installation Manual Adding a Second Set of I/O Cards A Flat cable (#21760300) B Flat cable (#21760300) C EIO 2 D MIO 2 E EIO 1 F MIO 1 G Red conductor = pin 1 H To motherboard AUDIO connector I To motherboard USB connector (MIO 1 only) J Flat cable (#16540260) To insert a second set of I/O cards, proceed as follows: 1. Insert all cards into appropriate slots (see Physical Position on page 49). 2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 8.11 Configuring the Internal I/O Cards The FastTrace 2 server automatically detects all connected MIO and EIO cards. To configure the inputs and outputs, see the XOa Client Software User Manual. 8.12 Input Circuits Use the ADPRO XOa client to configure the inputs as NEOL, SEOL, or DEOL.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9 Main and Extension I/O Cards Next Generation 9.1 Features The Main I/O (MIO) and Extension I/O (EIO) Next Generation cards are internal I/O cards, to be fitted inside the ADPRO FastTrace 2/2E system. They are also called OTB (on-the-board) cards.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9.4 Material List 9.4.1 Main I/O Card with Mounting Set (#39544000) Part Amount + Reference Number Main I/O card (incl. mounting bracket, M3 screws, and hex spacers) 1 x #39544070 (1 x #17291161) (2 x #17439030) (2 x #17210070) Part Amount + Reference Number L-profile 1 x #17291141 Locknut 1 x #17439020 Screw M2.5 2 x #17420060 Nut M2.5 2 x #17429000 Dented washer M2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Part Amount + Reference Number Flat cable (6 pins x 35 cm) 1 x #21760101 Flat cable (10 pins x 20 cm) for USB 1 x #16540260 Flat cable (10 pins x 30 cm) for audio 1 x #16540280 Reset cable 1 x #21760402 Part Amount + Reference Number Connector adapter for DG41TY and DH61BE motherboards 1 x #16500660 Connector adapter for PH10LU motherboard 1 x #16500665 DG41TY: place the adapter on the AUDIO connector.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9.4.2 Extension I/O Card with Mounting Set (#39544010) Part Amount + Reference Number Extension I/O card (incl. mounting bracket, M3 screws, and hex spacers) 1 x #39544080 (1 x #17291161) (2 x #17439030) (2 x #17210070) Flat cable (26 pins) 1 x #21760300 Part Amount + Reference Number L-profile 1 x #17291141 Locknut 1 x #17439020 Screw M2.5 2 x #17420060 Nut M2.5 2 x #17429000 Dented washer M2.
ADPRO® FastTrace™ 2 Series Mounting on chassis: PCI connector: PCI Express connector: 21790_05 Hardware Installation Manual A I/O card, bottom side B Locknut (#17439010) C M3 stud D Chassis E L-shaped metal bracket (#17291141) – on top side F Screw M2.5 (#17420060) Nut M2.5 (#17429000) Dented washer M2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9.6 Settings on the Main I/O Card If you are connecting PTZ cameras from the same RS-485 bus to multiple FastTrace 2 servers, set the RS-485 PTZ jumper on the Main I/O card to the 2-wire (PTZ) position. RS-485 cable length: max. 1200 m. A PTZ and audio (VM22) G USB port; to second Main I/O card B To AUDIO on motherboard (#16540280) H To nearest USB port on motherboard (#16540260) On 1st Main I/O: addressed as /dev/ttyU6.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 3. Remove the two cables that connect the LED board on the front to the motherboard. The LEDs will be powered from the Main I/O card (of the 1st set). 4. 5. Remove the female connectors (A, see figure below) from the Main I/O card before installing. Before inserting the Main I/O card into the motherboard, connect all necessary cables to the card. See the table below for an overview of cable connections. 6. 7.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual DG41TY motherboard A AUDIO (to MIO card), use adapter #16500660 B USB (to MIO card) C Reset (to MIO card) DH55TC motherboard 64 A AUDIO (to MIO card) B USB (to MIO card) C Reset (to MIO card) 21790_05
ADPRO® FastTrace™ 2 Series Hardware Installation Manual DH61BE motherboard A AUDIO (to MIO card) B USB (to MIO card), use adapter #16500660 C Reset (to MIO card) PH10LU motherboard 9.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Note Check the polarity! If you reverse the connection, the motherboard receives a permanent reset signal. 9.9 Adding an Extension I/O Card 9.9.1 Settings on the Extension I/O Card A From Main I/O card (#21760300) No settings are required on the Extension I/O card. 9.9.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9.10 Adding a Second Set of I/O Cards A Flat cable (#21760300) B Flat cable (#21760300) C EIO 2 D MIO 2 E EIO 1 F MIO 1 G Red conductor = pin 1 H To motherboard AUDIO connector I To motherboard USB connector (MIO 1 only) J Flat cable (#16540260) To insert a second set of I/O cards, proceed as follows: 1. Insert all cards into appropriate slots (see Physical Position on page 60). 2.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Warning! Although the pictures below show only the connector, it is strongly recommended to connect the wires with the connectors plugged into the card. Wiring a handheld connector may cause injuries. 9.11.2 Connecting Inputs/Outputs Wiring to Dinkle and Phoenix connectors is identical; except that the position of tabs and holes is swapped. The picture in the procedure below shows a Phoenix connector.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 9.13 Input Circuits Use the ADPRO XOa client to configure the inputs as NEOL, SEOL, or DEOL.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 10 Required Encoder (A/V) Card You use different video cards (encoder cards) with different motherboards in the FastTrace 2 video system: Use DS40xx-HCI encoder cards with the Intel DG31PR and Intel DG41TY motherboards. Use DS42xx-HFVI-E encoder cards with the Intel DH55TC, Intel DH61BE, and MiTAC PH10LU motherboards. Do not mix different cards within the same video system.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual audio compression OggVorbis Codec 16 kbps (DS40xx cards) OggVorbis Codec G711 (DS42xx cards) bandwidth Compression, fps, and quality are remotely adjustable. You can specify a bandwidth limit in the XOa client software. bandwidth consumption 6 fps CIF/SIF: 70 kbps 12 fps 4CIF/SIF: 400 kbps in optimal quality PTZ Several protocols available For a detailed list, see the XOa Client Software User Manual.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series It is recommended to return the faulty video card to your reseller. Switch on the power supply and reboot the video system. The replacement part will include a new license. Upload the received license file to the server. For more information on uploading files to the video system, see the XOa Client Software User Manual. 10.4 Adding a Video Card Switch off the power supply. Open the casing and insert the new video card (in a free slot).
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 10.5 Video Input Termination (75 Ohm/High Impedance) This is only available on the latest version of the 8 or 16 channel video cards. Jumpers JP1–JP8/16 determine whether the corresponding video input is terminated with 75 ohm (if jumper is placed) or not (if jumper is removed).
Hardware Installation Manual 11 ADPRO® FastTrace™ 2 Series HIPI Card for IP Cameras The HIPI card offers an isolated LAN network (10/100/1000 Mbps on RJ45 connector) to connect IP cameras. Note The HIPI card can also function as Ethernet card from version 2.9 onwards. The HIPI card is no longer used for new FastTrace 2 units. It is not compatible with the MiTAC PH10LU motherboard. 11.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Note The HIPI Ethernet interfaces use ETH1 and/or ETH2, not ETH0. In case of 2 HIPI cards with IP only, there is no restriction in which camera is connected to which port. A 16-camera network can be connected to a single port. The HIPI card is automatically detected by the FastTrace 2 video system. Each HIPI card must be configured with a different IP address and a subnet mask.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 11.2 Adding a HIPI Card Use these reference numbers when ordering your HIPI card with Xtralis: Extension Board Reference Number HIPI card: card only 39544300 Hybrid HIPI card: card + mounting set 39544320 11.2.1 Placement on the Intel DG31PR Motherboard Insert the first HIPI card in PCI Express slot E. Insert the second HIPI card in PCI Express slot D. The card in slot E is assigned as ETH1 in the system.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 11.2.3 Placement on the Intel DH55TC Motherboard Insert the first HIPI card in PCI Express slot E. Insert the second HIPI card in PCI Express slot D. The card in slot E is assigned as ETH1 in the system. For more information, see the manual of the motherboard. 11.2.4 Placement on the Intel DH61BE Motherboard Insert the first HIPI card in PCI Express slot E. Insert the second HIPI card in PCI Express slot B.
Hardware Installation Manual 12 ADPRO® FastTrace™ 2 Series Ethernet Card 12.1 Installation FastTrace 2E units with Intel motherboards are standard equipped with an Ethernet card. Units with a MiTAC motherboard do not have an Ethernet card; the motherboard contains the necessary LAN connector.
ADPRO® FastTrace™ 2 Series 13 Hardware Installation Manual DTC Card The DTC card offers down-the-coax PTZ control for analogue cameras. The DTC card is built in at the factory; you cannot order it separately. It is inserted on the back of the audio/video connection board. The DTC card requires software. You can retrieve the current software version of the DTC card in the XOa client software. For more information, see the XOa Client Software User Manual.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 14 PTZ Cameras You can connect PTZ (Pan-Tilt-Zoom) cameras in one of the following ways for PTZ control: on the Main I/O card via a USB converter via the coaxial interface (DTC card) Each method is described in detail below. 14.
ADPRO® FastTrace™ 2 Series PTZ cameras Hardware Installation Manual Main I/O cards Next Generation 14.2 PTZ via DTC Some PTZ cameras can send the PTZ signal through the coax cable. If you want to use this, you must have your FastTrace 2 unit equipped with a DTC card. The DTC card is built in at the factory; you cannot order it separately. Open the PTZ window via System > Connections > Serial Ports / PTZ. Check if the DTC card is present.
Hardware Installation Manual 15 ADPRO® FastTrace™ 2 Series Presidium You can associate video outputs from a Presidium with FastTrace 2 analogue inputs. Use coax cables to connect the video outputs of the Presidium system to the video inputs of the FastTrace 2 video system for further analysis and recording. It is then possible to transmit alarms from the Presidium to the FastTrace 2 server over the IP network. See also the XOa Client Software User Manual.
ADPRO® FastTrace™ 2 Series 16 Hardware Installation Manual Modems You can connect one modem to your server. Normally, you connect a classic PSTN (ISDN) modem with serial port to the server by means of the USB to RS-232 converter. This USB to RS-232 converter needs a specific FTDI chip. The Stollman TA+USBA is the only ISDN modem with USB interface that is supported on the FastTrace 2 unit (without having to use the converter).
Hardware Installation Manual 17 ADPRO® FastTrace™ 2 Series Audio Not only video images can be used in the Live Video screen, also audio – both in and out – is possible. 17.1 Audio IN 17.1.1 Setup For cameras with an audio input, you can choose to record audio and listen to audio in the live view. Note If the connection bandwidth is low, it is recommended to disable live audio streaming. Audio IN is unbalanced audio. Changing the audio settings requires a system restart.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Wiring Diagram 17.1.2.
Hardware Installation Manual 17.1.2.3 ADPRO® FastTrace™ 2 Series ADPRO Audio Unit For more information, see the ADPRO Audio Unit Technical Datasheet.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 17.2 Audio OUT 17.2.1 Setup There is one general audio output available on the server: either via the MIO or via the audio out plug of the motherboard (= green 3.5 mm jack). If necessary, you can add VM22A audio units. Audio outputs are available on one or two VM22A units, connected in cascade. Unit 0 is controlled by the MIO card, and drives loudspeakers 1 to 10.
Hardware Installation Manual 4. 5. 6. 7. ADPRO® FastTrace™ 2 Series Click the Volume button under the Voice recording heading. Adjust the vertical volume slide on the Mic volume or Line volume, depending on which device you are using. Click OK and close the Control Panel. Test with Sound Recorder. In Windows Vista / Windows 7: 1. 2. 3. 4. Open Control Panel and click Hardware and Sound. Open the Recording tab in the Sound window.
ADPRO® FastTrace™ 2 Series 18 Hardware Installation Manual Connecting PIRs 18.1 Required PIR Firmware For a correct functioning of the PIR alarm processing, a minimal PIR firmware version 2.00 is required. Previous firmware versions also work with RS-485 communication, but do not support all features (e.g. Alarm Management). 18.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual (*) Some PIR models have separate 0V terminals for data and power; on other models there is only one common 0V terminal. The PIRs are powered locally by a power adapter. You can place locally powered PIR detectors at the maximum distance of 1200 m for RS-485 cables, but remember that this remains a 3-line communication (RS-485 + 0V). Make sure that there is no difference in earth potential between the server and the PIR. 18.2.1.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual (*) Some PIR models have separate 0V terminals for data and power; on other models there is only one common 0V terminal. The PIRs are powered locally by a power adapter. You can place locally powered PIR detectors at the maximum distance of 1200 m for RS-485 cables, but remember that this remains a 3-line communication (RS-485 + 0V). Make sure that there is no difference in earth potential between the server and the PIR.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series A detailed view of one connected distribution unit: 18.2.3 Connecting the PIR Detector Using a USB to Serial Port RS-485 Converter Connect the PIR detector to the converter and plug the USB cable of the converter in the dev/ttyU2 USB port of the server. Restart the XOa client software after connecting the PIR to the USB port.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual You need to order the USB to serial port RS-485 converter separately (reference number 20415490).
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 19 Network Load Application Bandwidth volume Alarm transmission Negligible Remote control (executing commands) Negligible Software update Volume of about 170 MB Configuration update Volume of 150 kB Video streaming 4CIF / 25 ips 400 kbps / camera 4CIF / 6 ips 140 kbps / camera CIF / 25 ips 80 kbps / camera CIF / 6 ips 43 kbps / camera QCIF / 25 ips 17 kbps / camera QCIF / 6 ips 6 kbps / camera Audio in 16 kbps / camera (with
ADPRO® FastTrace™ 2 Series 20 Hardware Installation Manual Current Consumption Estimated current consumption depends on the installed components and on the system load: Motherboard 16 W (Intel) Processor 25 W (AMD) Intel DG31, DG41: 65 W max. Intel DH55: 73 W max. Intel DH61: 77 W max. 4 channel A/V card 3.
Hardware Installation Manual 21 ADPRO® FastTrace™ 2 Series Retrieving the IP Address Connect a monitor/screen and keyboard to the server. If the video matrix is active, press Ctrl+Alt+F1. The welcome screen appears: Video Security FastTrace 2E (XOa V3.00.003) Ip: 10.0.0.10 Subnet: 255.255.255.0 Gateway: 10.0.0.1 The welcome screen displays the following information: Server model and software version IP address, subnet mask, and gateway.
ADPRO® FastTrace™ 2 Series 22 Hardware Installation Manual Diagnostics In case of major troubles with the server, the system allows to generate a number of traces. In some cases, the Xtralis Support Division may ask you to activate and capture some traces and files that can be helpful to resolve any technical issues. 22.1 Retrieving Traces The server can output its internal trace buffer to hard disk to allow tracing for longer periods of time without losing the data.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series Click the link on the web page. Click Save to store the file on your PC or a network folder. Do not try to find a program online, because this will provide unexpected websites. Click Open and choose Notepad as the default application.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 22.2 Retrieving Reports The server generates a number of reports. You can view these reports via the internet browser. Type the IP address of the server in the address bar of the browser and add /report.php to the IP address. Example: http://10.0.0.10/report.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Performance Vmstat I/O stat PID stat MP stat Network Interfaces – available Interfaces – enabled Routes Listen ports Netstat – all DEV stats Sockstat ARP cache Filesystem Mounts S.M.A.R.T Fsck Open files Free disk space Hardware CPU Memory Mainboard PCI Udev database Server Server version Server process memory usage Files Active config Contact the Xtralis Support Division for further assistance.
ADPRO® FastTrace™ 2 Series 23 Hardware Installation Manual FastTrace 2 Web Pages There are several web pages to consult with the FastTrace 2. To open these web pages in your internet browser you need to type the IP address in the address bar, followed by the extensions as described in the table below. Web page Description index.php This is the main page of the FastTrace 2.
Hardware Installation Manual 24 ADPRO® FastTrace™ 2 Series Maintenance 24.1 Replacing the Filters It is essential that the filters are regularly cleaned and – when needed – replaced by new filters. You need an Allen wrench (3 mm) to remove the front plate of the FastTrace 2 server. Remove the screws indicated by the white arrows on the image below and remove the front plate. Remove the dirty filters and replace them by clean ones (or new filters).
ADPRO® FastTrace™ 2 Series 25 Hardware Installation Manual Product Labelling 25.1 Labels All ADPRO products are labelled. Older systems: Device Marking on Device FastTrace 2 XTRALIS Security Solutions BELGIUM TYPE: ADPRO FastTrace 2 ASSY number 54VHHID0 – YYMM 100–240 VAC; 50/60 Hz; 6 A FOR INDOOR USE ONLY sn. YYYY – 54VHHID0- nnnn Marking on Package XTRALIS Security Solutions BELGIUM TYPE: ADPRO FastTrace 2 ASSY number 54VHHID0 – YYMM 100–240 VAC; 50/60 Hz; 6 A FOR INDOOR USE ONLY sn.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 25.2 Product Number Structure 25.2.1 FastTrace 2 and FastTrace 2X Units Each product version has an 8-digit product number, indicating the installed options.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual 25.2.2 FastTrace 2E Units Each product version has an 8-digit product number, indicating the installed options.
Hardware Installation Manual ADPRO® FastTrace™ 2 Series 25.3 Declaration of Conformity Warning! The FastTrace 2 video system is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
ADPRO® FastTrace™ 2 Series Hardware Installation Manual Appendix A: Abbreviations 3G: third generation GND: ground A: ampere GUI: graphical user interface AGC: automatic gain control HD: high definition AHCI: Advanced Host Controller Interface HDD: hard disk drive APN: Access Point Name HDMI: High-Definition Multimedia Interface HPET: High Precision Event Timer A/V card: audio/video card AWG: American wire gauge BIOS: basic input output system HTTP: hypertext transfer protocol BNC: Bayonet Nei
ADPRO® FastTrace™ 2 Series Hardware Installation Manual pF: picofarad SP: Service Pack PIN: personal identification number SPK: speaker PIR: passive infrared SVGA: Super Video Graphics Array PoE: power over Ethernet SXGA: Super Extended Graphics Array PPP: point-to-point protocol Sync: synchronisation PSTN: public switched telephone network TB: terabyte PTZ: pan tilt zoom TCP: transmission control protocol QCIF: quarter CIF TX: transmission QSIF: quarter SIF UDP: user datagram protocol R
www.xtralis.com UK and Europe +44 1442 242 330 D-A-CH +49 431 23284 1 Middle East +962 6 588 5622 Asia +86 21 5240 0077 The Americas +1 781 740 2223 Australia and New Zealand +61 3 9936 7000 A Disclaimer about this document, statements about Intellectual Property, Copyrights, and Liability, as well as a General Warning are available in an earlier section of this document. Doc.
