Submittal Sheet

TEST
Tensile Strength
Elongation
Durometer (Shore A)
Accelerated Aging
Compression Set
Oil Immersion
Ozone Cracking
Tear Resistance
Water Absorption
GASKET PHYSICAL TESTS (ASTM C 564)
1500 PSI minimum
250% minimum
70 ± 5 @ 76˚F ± 5˚F
15% maximum tensile and 20% maximum elongation
deterioration. 10 points maximum increase in hardness.
All determinations after oven aging for 96 hours at 158˚F.
25% maximum after 22 hours at 158˚F
80% maximum volume change after immersion in ASTM
oil #3 for 70 hours at 212˚F
No visible cracking at 2X magnication of the gasket after 100
hours exposure in 1.0 PPHM ozone concentration at 104˚F.
Testing and inspection to be on gasket which is loop-mounted
to give approximately 20% elongation of outer surface.
Die C 150 lbs. minimum per inch of thickness
20% maximum by weight after 7 days at 158˚F
ASTM
C 564
D412
D412
D2240
D573
D395
D471
D624
D471
SEALING
GASKET
DIMENSIONS
D
1½"
2"
2" x 1½"
3"
3" x 2"
4"
4" x 3"
5"
6"
8"
10"
12"
15"
W
3
3
3
3
3
3
3
4
4
4
4
5.5
5.5
B
0
0
0
0
0
0.875
0.875
2.750
2.750
2.750
2.750
4.000
4.000
C
7.813
9.313
9.313
12.563
12.563
15.063
15.063
17.500
19.875
26.250
33.813
39.000
49.875
L
7.813
9.313
9.313
12.563
12.563
15.938
15.938
20.250
22.625
29.000
36.563
43.000
53.875
W
3
3
3
3
3
3
3
4
4
4
4
5.5
5.5
MISSION
REFERENCE
1½" - C150 HW
2" - C200 HW
2" x 1½" - C215 HW
3" - C300 HW
3" x 2" - C320 HW
4" - C400 HW
4" x 3" - C430 HW
.
5" - C500 HW
6" - C600 HW
8" - C800 HW
10" - C1000 HW
12" - C1200 HW
15" - C1500 HW
CORRUGATED SHIELD DIMENSIONS
D
.15
.18
.09
DETAIL C
SCALE 1 : 1
DETAIL D
SCALE 1 : 1
SIZES 5" - 10"
9 SEALING
RINGS/SIDE
SIZES 1½" - 4"
6 SEALING
RINGS/SIDE
SEALING GASKET DETAILS
W
D
.30
.19
.29
.09
D
W
C
.19
.36
.75
.81
MAX
.026 ± .003
CLAMP DETAILS
HOUSING
.50
⁄" HEX HEAD
SCREW
.47
1.21 MAX
SADDLE
.30
.08 ± .02
CORRUGATED SHIELD DETAILS
.0075 ± .001
.50
.030 ± .004
100 80 70 60
0.020
0.025
0.030
0.035
0.040
0.045
SCREWS TORQUE (INCH POUNDS)
TENSION IN BAND (INCHES))
HEAVYWEIGHT
FROM
BAND TENSION
ADDITIONAL
NO HUBS
FROM STD.
TENSION
USABLE
TYPICAL BAND TENSION VS. HW TORQUE
(AISI 305 SCREWS)
SIZES 1½" THROUGH 4" - 4 BANDS
SIZES 5" THROUGH 15" - 6 BANDS
MEETS:
FM 1680 CLASS 1
ASTM C 1540
ASTM C 564
ASTM A240/A240M
CSA B602
IAPMO 7816
For Heavy Duty
Installations Requiring
More Than a Standard
No Hub Coupling
HeavyWeight Coupling - Submittal
Performance Couplings for Hubless Cast Iron Pipe and
Fitting
s
PROJECT_____________________________________________
ENGINEER____________________________________________
CONTRACTOR_________________________________________
________
PROJECT _____________________________
ENGINEER ____________________________
CONTRACTOR _________________________
MATERIALS
Band Series 304 ASTM stainless steel
Screw Housing Series 304 ASTM stainless steel
Screw Saddle Series 304 ASTM stainless steel
Screw Series 305 ASTM stainless steel
Shield Series 304 ASTM stainless steel
Gasket This gasket is fabricated from a compound with high-quality elastomeric properties
to meet physical testing.
Extended Width - Greater surface load bearing contact of 304 stainless steel shield
accommodates additional sealing clamps and provides for greater load bearing
control between the coupling and surface of the pipe and tting.
Joint Movement Restraint - Additional sealing rings are incorporated into the
circumferentially continuous sealing gasket and meet the requirements of ASTM C
564. The internal profile of the elastomeric gasket ensures a uniform seal through-
out the entire coupling, increasing performance in all cast iron DWV systems.
Pre-Set Calibration - All HeavyWeight Couplings are designed to be installed with
a pre-set torque wrench calibrated to 80 in/lbs. maximum to accommodate the 305
stainless steel ⁄" hex head/shoulder screw.
Rev. 11/16
Mission’s HeavyWeight Coupling is designed to connect cast iron hubless soil pipe
and ttings in sanitary and drain waste and vent (DWV) applications. Couplings
consist of multiple heavy duty 304 series stainless steel worm drive clamps attached
to a heavy duty corrugated 304 series stainless steel shield, over a molded one-piece
elastomeric sealing gasket. Couplings are available in sizes 1½" to 15": 1½" to 4"
utilize four (4) clamps; 5" to 15" utilize six (6) clamps.
Leak-Proof Seal - Stainless steel clamps are 8% thicker than those of a standard no
hub coupling, providing a positive seal when properly tightened to 80 in/lbs. of
torque. Axially slotted clamps enable bands to tighten independently to accomo-
date variances in the outside diameters of the pipe and fittings to be joined,
ensuring a water-tight, leak-proof and root-proof seal.
Corrosion Resistant - 304 series stainless steel components provide highly eective
corrosion resistance in a variety of environments.
Mission Rubber Company LLC
1660 Leeson Lane
Corona, CA 92879
[phone] • Fax [phone]
missionrubber.com