Forever Collection 1/4” FRAMELESS SLIDING DOOR FOR TUB OR SHOWER Models: MSDFVR5412581257 / MSDFVR5412581256 MSDFVR43476512 / MSDFVR5412581270 MSDFVR48526512 INSTALLATION INSTRUCTIONS miseno.com 855.480.2915 infoservice@miseno.
MAINTENANCE: Two primary materials are used to manufacture your new shower enclosure: tempered glass and anodized aluminum. To assure a long-lasting finish on the enclosure, wipe it down with a towel after each use. Never use a scouring agent to clean the aluminum. For occasional, more concentrated cleaning efforts, we find that Lysol Bathroom Cleaner works extremely well. Be sure that any overspray falling on the aluminum frame is rinsed thoroughly and dried.
PARTS LIST A. B. C. D. E. F. G. H. I. J. 1 2 6 6 4 1 2 4 4 8 Tub Track with Vinyl Wall Jambs #8 x 2” Truss Head Screws Plastic Wall Anchors Nylon Spacers Header Glass Panels Hanger Brackets (Pre-assembled) Back Plates Clear Plastic Discs K. L. N. S. T. U. V. X. Y. Z.
Step 1 Measure the wall-to-wall opening at the center of the tub rim. Cut the tub track [A] 1/16” short of this dimension. An inexpensive miter box available at your local hardware store will help you get clean square cuts. WALL JAMB Position the tub track in the center of the tub rim with the tall leg to the exterior. It may be necessary to file a radius on the ends of the tub track and wall jambs to match the corners of the tub.
Step 4 WALL JAMB Replace one wall jamb [B] and attach to the wall with a #8 x 2” truss head screw [D] inserted through the center hole. Slip a nylon spacer [E] over a #8 x 2” truss head screw and install in the top hole of the wall jamb. Repeat for the bottom jamb. Check jamb for plumb and tighten screws. NYLON SPACER NOTE: Do not overtighten the jamb screws. #8 x 2” TRUSS HEAD SCREW Step 5 NOTE: Header shown cut away for clarity.
Step 7 Slide anti-jump stops into position: 1) at left wall jamb 2) at right wall jamb 3) centered in opening Insert SCR11 screw into the pre-drilled hole of each insert. The screws will just press against the header. DO NOT use power tools to insert these screws. DO NOT drill the header for these holes. PRO TIP! If the rollers contact the anti-jump during normal operation, back the screw out of the insert 1/4 of a turn at a time until less contact is made.
Step 9 Slide one of the clear plastic discs [J], then a glass hole sleeve [K] onto the back plate [I]. Push the assembly through the hole in the glass panel, so that the glass hole sleeve is flush with the other side of the panel. Slide the other clear plastic disc onto the protruding end of the back plate, and then slide on the front plate [L]. Repeat this for the second hole on the panel. While holding the towel bar [N] in place, and screw the back plates into the towel bar.
Step 11 EXTERIOR Lift the interior glass panel into position with the rollers engaging the groove in the header [F]. Repeat for the exterior panel. If panels are not parallel to the respective wall jambs, and adjust the rollers up or down in their slots are compensate. HEADER INTERIOR PANEL EXTERIOR PANEL TUB TRACK Please Note: Panels will need to be very close to the center of the opening in order to be installed.
Step 12 Locate the nylon bottom guide [S] in the middle of the tub track [A] with the glass panels in the position shown. With the 7/64” bit, drill two holes into the V-groove through the mounting holes in the guide. Install the bottom guide with two #6 x 3/8” pan head screws [T] through the drilled holes as shown. GLAZED PANELS CENTER GUIDE TUB TRACK (2) #6 X 3/8 “ PAN HEAD SCREW INTERIOR Step 13 Slide the stainless steel bumper inserts [U] into the four soft vinyl jamb bumpers [V].
