Installation Sheet

ManualsBrandsMiseno ManualsDeadboltPrivacy One Sided Full Bore Deadbolt

Table Of Contents

页 1

Door Lock Instructions New Door Preparation

Insert Latch into Hole and keeping it parallel to the

door Edge mark the Outline

Mortise the Door edge with a Chisel or Router 1/8”

deep or until the latch Face plate is flush with the door

when installed

Insert Latch into hole in door

and Mark where it will hit

the door Jamb when properly

closed.

Drill a 1” hole a Minimum of 1”

deep into the door Jamb at the

position Marked

If the Door is a tight fit to the

Jamb you may need to mark

the strike and mortise the

Jamb so the strike sits flush to

the door

JAMB

Step 4 : Prepare Jamb for Strike

Step 3 : Mortise Door for Latch

Fold Template below on

Fold Line and Mark Door

for Lock Bore Hole at

2-3/4” or 2-3/8” Backset

and lock Edge Hole

Centered on the door

edge.

Note: Most exterior doors

2-3/4” Backset is used

Drill through Door Face with

2-1/8” hole saw. Drill one

side until Guide Bit punches

through then Drill from

through with the Hole saw

from the other side to

Complete the Lock Bore Hole

Drill the 1” Latch Hole from

the door edge fully into the

Lock Bore hole

Common Standard for Lock Height off Floor is 36” above the floor.

Deadbolt should be 5.5” above the entrance Knob or lever

2-3/8" BACKSET

2-3/4" BACKSET

MARK FOR 2-1/8"(54mm)

HOLE IN DOOR FACE

2-1/8"(54mm) HOLE

1"(25mm) HOLE

Step 1 : Mark Door

Step 2 : Drill Holes

2-3/8" BACKSET

2-3/4" BACKSET

MARK FOR 1"(25mm)

HOLE IN DOOR EDGE

IMPORTANT!

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

THEN DRILL 1"(25mm)

IN CENTER DOOR OF EDGE

HOLE

FOLD HERE ON

DOOR EDGE

2 /8"(60mm) BACKSET

MARK

FOR

1-3/4"(45mm)

DOOR

DRILL

2-1/8"(54mm)

HOLE

MARK CENTER

OF HOLE ON

DOOR FACE

TEMPLATE

2 /4"(70mm) BACKSET

MARK

FOR

1-3/8"(35mm)

DOOR

FOR INSTALLING

ENTRY LOCK AND DEADBOLTS

Customer Service 800-221-3379

Instruction_Lock_44

JSC-FGS-D101S-M

Customer Service 800-221-3379

Instruction_Lock_44

JSC-FGS-D101S-M

Full Bore One-Sided Deadbolt Lock Installation

Step 1 : Adjust Latch Backset to match your door

Step 2 : Install Latch into the door

Step 3 : Install Lock body

Step 4 : Install Strike

To adjust the backset from 2-3/8" to 2-3/4" follow these steps.

Retract the latch bolt.

Hold the latch tail and

rotate the faceplate

towards you.

Rotate the latch faceplate

away from you and check

to see if the notch is at

the 2-3/4" mark.

Once the notch is in

the groove, pull the

latch faceplate away

from the latch tail.

To adjust the backset from 2-3/4" to 2-3/8" follow these steps.

Retract the latch bolt.

Hold the latch tail and

rotate the faceplate

towards you.

Rotate the latch faceplate

away from you and check

to see if the notch is at

the 2-3/8" mark.

Once the notch is in

the groove, push the

latch faceplate towards

the latch tail.

Install Latch into door and Screw into door with wood screws provided with lock.

Install Strike and test lock

Adjust Strike position if necessary, for firm Closure.

A) Install exterior of lock by Inserting Studs through round holes until plate is Flush with the door.

B) Install the interior of the lock by inserting the spindle into cross cam of latch and pressing Flush to the door. Insert screws

through holes and tighten down with a hand-held screwdriver.

Note: Check alignment of the lock as you tighten the screws to keep lock centered over the bore Hole

1" THROW

TURN

PIECE

TORQUE

BLADE