Installation Sheet

ManualsBrandsMiseno ManualsHardwareBuchanan Tulip Privacy Door Knob Set

Table Of Contents

页 1

Customer Service 800-221-3379

Instruction_Lock_11

MOUNTING

PLATE

INSIDE

ASSEMBLY

JSC-FGS-5762

Customer Service 800-221-3379

Instruction_Lock_11

2- 3/8"(60mm)

2- 3/4"(70mm)

SLIDE

EXTENSION

Note: To reverse the adjustment from 2-3/4"(70mm) to 2-3/8"(60mm):

1) Depress latch (e)

2) Catch the open slot on the rear of the extension piece (f) on the notch (g) inside the latch.

3) Lower extension piece into latch while at the same time releasing the latch. Proceed to

step 4 of the instructions for installing lockset.

Door Lock Instructions New Door Preparation

Insert Latch into Hole and keeping it parallel to the door

Edge mark the Outline

Mortise the Door edge with a Chisel or Router 1/8” deep

or until the latch Face plate is flush with the door when

installed

Insert Latch into hole in door

and Mark where it will hit

the door Jamb when properly

closed.

Drill a 1” hole a Minimum of 1”

deep into the door Jamb at the

position Marked.

If the Door is a tight fit to the

Jamb you may need to mark

the strike and mortise the

Jamb so the strike sits flush to

the door.

JAMB

Step 4 : Prepare Jamb for Strike

Step 3 : Mortise Door for Latch

Fold Template below on

Fold Line and Mark Door

for Lock Bore Hole at

2-3/4” or 2-3/8” Backset

and lock Edge Hole

Centered on the door

edge.

Note: Most exterior doors

2-3/4” Backset is used

Drill through Door Face with

2-1/8” hole saw. Drill one

side until Guide Bit punches

through then Drill from

through with the Hole saw

from the other side to

Complete the Lock Bore Hole

Drill the 1” Latch Hole from

the door edge fully into the

Lock Bore hole

Common Standard for Lock Height off Floor is 36” above the floor.

Deadbolt should be 5.5” above the entrance Knob or lever

2-3/8" BACKSET

2-3/4" BACKSET

MARK FOR 2-1/8"(54mm)

HOLE IN DOOR FACE

2-1/8"(54mm) HOLE

1"(25mm) HOLE

Step 1 : Mark Door

Step 2 : Drill Holes

2-3/8" BACKSET

2-3/4" BACKSET

MARK FOR 1"(25mm)

HOLE IN DOOR EDGE

IMPORTANT!

PLACE TEMPLATE

ON HIGH EDGE OF

DOOR BEVEL

THEN DRILL 1"(25mm)

IN CENTER DOOR OF EDGE

HOLE

FOLD HERE ON

DOOR EDGE

2 /8"(60mm) BACKSET

MARK

FOR

1-3/4"(45mm)

DOOR

DRILL

2-1/8"(54mm)

HOLE

MARK CENTER

OF HOLE ON

DOOR FACE

TEMPLATE

2 /4"(70mm) BACKSET

MARK

FOR

1-3/8"(35mm)

DOOR

FOR INSTALLING

ENTRY LOCK AND DEADBOLTS

Install Latch into door positioned so that wedged shaped side of Bolt engages

the strike first when closing the door

Door Lock Installation

Step 1 : Adjust Latch Backset

Step 2 : Install Latch into the door

SPINDLE

STEMS

Step 3 : Install Lock body

Step 4 : Install Strike

Install exterior of lock by Inserting Lock Spindle Through Half Moon Opening

and Studs through round holes until lock is Flush with the door. (Press in and

Hold Latch to make inserting spindle easy)

For Knobs with vertical key slots the knob should be installed with the Key Slot

positioned so that the Key will be teeth up when used.

Install the interior of the lock by inserting it over the spindle and pressing Flush

to the door. Insert screws through holes and tighten down with a hand-held

screwdriver.

Note: It may be necessary to twist lock knob on interior assembly of lock to align

with connector bar.

Note: Check alignment of the lock as you tighten the screws to keep lock centered

over the bore Hole

Install Strike and test from inside.

Adjust Strike position if necessary, for firm Closure.

Entry Lock only –

Ensure Security

Pin Seats Properly

JSC-FGS-5762

1. The latch is factory preset at 2-3/8"(60mm) backset, which is standard for most doors.

2. To use the 2-3/8"(60mm) backset, no adjustment is required, simply insert the screw

stems on the outside knobs thru holes (a) & (c) of the latch, proceed to step 4 of the

instructions for installing lockset.

A) FOR 2-3/8"(60mm) BACKSET INSTALLATION

B) FOR 2-3/4"(70mm) BACKSET INSTALLATION

1. Push in front of latch (e) and hold lt.

2. Use a screwdriver to push the black insert slide extension up or down

from inside the latch. For best results, while keeping the latch depressed,

push down on the top front ( closest to e ) of the extension slide, while at the same

releasing the latch.

and remove the

slide extension

3. Latch is ready for installation.

4. When using the 2-3/4"(70mm) backset, lockset screw stems are inserted through hole (b)

of the latch and against the outside of location (d) on the latch. proceed to step 4 of the

instructions for installing lockset.