Installation Sheet

ManualsBrandsMiseno ManualsDeadboltElectronic Keyless Entry Deadbolt with Rectangular Rosette and Touch Screen

Table Of Contents

Insert the latch and ensure it is parallel to the door face.

Mark the outline of the faceplate, then take out the latch.

faceplate to be aligned with the door edge.

Note: It is not necessary to chisel the door edge for the

faceplate installation if you use the drive-in latch.

Chisel 5/32" (4 mm) deep along the outline to allow the

Install Latch

You need to stay this

way up when inserting

the latch.

Insert the latch into the door.

(Make sure the cross is on the

bottom of the latch.)

Use 2 wood screws to secure

latch.

Please do not fully tighten the

screws until lock is completely

installed.

Install Drive-in Latch

Drive the latch into the

hole on edge of door.

Mark the Door with Template

Select the height and backset as desired on the

door face; use the TEMPLATE as an indication to

mark the centre of the circle on the door face and

the centre of the door edge.

Machine Screws Qty. 3

Wood Screws Qty. 5

Deadbolt Chassis Screws Qty. 2

J K

Do not use an electric screwdriver during installation.

Backset is a distance from door edge to centr of

hole on door face.

Adjustable latch fits both backset of 2-3/8" (60 mm)

and 2-3/4" (70 mm).

Backset Determination

Drill Holes

Using the marks as a guide to drill a hole

Ø 2-1/8" (54 mm) through the door face for the lockset,

then a hole of Ø 1" (25.4 mm) for latch.

PACKAGE CONTENTS

HARDWARE SCREWS CONTENTS

TOUCHPAD

ELECTRONIC DEADBOLT LOCK

Installation Guide

Description

Quantity

Part

Key

Cylinder

Deadbolt Touchpad Assembly

Deadbolt Latch

Strike Plate

Mounting Plate

Part

Description

Quantity

Receiver Assembly

Battery Cover

Drive-in Sleeve

Determine if the latch needs to be adjusted to the 2-3/4" (70 mm) backset.

To adjust, rotate the latch until it stops.

Reverse the direction to return to the 2-3/8" (60 mm) backset.

LATCH ADJUSTMENT

CHANGE LATCH FACE

Determine which latch mounting method will be used

and make necessary adjustments.

No adjustment required for square latch face plate.

a. Use a flat screwdriver to separate the face plate.

b. Snap selected latch face onto back plate.

Drive-in Installation

Remove original latch faceplate.

Align the as illustrated

and snap into the latch case.

drive-in sleeve

2-3/4" (70 mm)2-3/8" (60 mm)

180°

70 mm

Drive-in Latch

60 mm

FGS- 1PL2-

Summary of content (3 pages)

PAGE 1
2 3 4 5 6 7 8 9 FGS-PL2-1 CHANGE LATCH FACE TOUCHPAD ELECTRONIC DEADBOLT LOCK 0 Determine which latch mounting method will be used and make necessary adjustments. No adjustment required for square latch face plate. a. Use a flat screwdriver to separate the face plate. b. Snap selected latch face onto back plate. a Installation Guide b Drive-in Installation Remove original latch faceplate. Align the drive-in sleeve as illustrated and snap into the latch case.
PAGE 2
5 9 Install Strike b Adjust Thumb Turn Piece Rotate the thumb turn piece to the LEFT at 45 degrees for right-handed doors. Rotate the thumb turn piece to the RIGHT at 45 degrees for left-handed doors. To identify the centre of strike: close the door to lay the latchbolt against the door frame. Mark the centre line on the doorframe exactly opposite the latch hole in the door edge. Measure one half of door thickness from door stop and vertically mark centre line of strike. Drill 1" (25.
PAGE 3
FGS-PL2-2 TOUCHPAD ELECTRONIC DEADBOLT LOCK USER GUIDE ! Default programming code (PC): 0000 Default user code (UC): 1234 Your new programming code (PC) ____________ Your new user code (UC) ___________________ 8 Enter PC 9 Feature: Keypad Security Setting Create a One-Time User Code 4–10 Digits Long 8 Enter PC How to Wake-Up Your Lock- Touch the keypad screen. A random series of numbers will appear and must be pressed to unlock the screen. You can then enter your user code to unlock the door.