Installation Sheet

5.INSTALL EXTERIOR MECHANISM
A. Press cylinder side flush against door
the torque blade is properly positioned in latch crank.
B. Tapped holes in mounting plate of exterior cylinder
should be lined up with latch holes. Key hole should
be in down position.
making certain
6.INSTALL INTERIOR MECHANISM
A. Slide thumb bar and interior
rosette onto torque blade.
B. Insert machine screws through
engaging holes in cylinder and tighten.
holes
1" THROW
TURN
PIECE
Exterior half is fully assembled with exterior torque blade
EXTERIOR TORQUE BLADE
NOTE: The interior torque blade is inserted into the exterior blade.
INTERIOR TORQUE BLADE
A. Install interior cylinder
NOTE: This assembly is placed through latch first.
B. Press interior assembly flush
door making certain the torque blade
is properly positioned in latch hole.
Key hole should be in down position.
against
C. Insert(2) two screws through
countersunk holes engaging holes
in exterior cylinder and tighten.
1.MARK DOOR
A. Fold and apply template to high
edge of door bevel and mark center
of door edge as
indicated on
template at
the desired
height from
the floor.
B. Mark center hole
face through guide
on template for
either 2-3/8"
(60mm) or
2-3/4"
(70mm)
backset.
on door
2.DRILL HOLES
A. Drill thru door face as marked
lockset: It is recommended that
holes be drilled from both sides
to prevent spliting. Hole
size is 2"(50.8mm)
for standard
installations.
for
B. Drill 1"(25mm)
hole in center
of door edge
thru to
2"(50.8mm)
hole for
latch.
B. Chisel 1/8"
deep or until
latch face is
flush with
door edge.
C. Install deadbolt latch in
up position into
hole as shown
on latch insert
and tighten
screws.
4.INSTALL STRIKE
A. Bore 1" hole
deep for deadbolt.
1"minimum
B. Mortise 1/16" deep for strike
locating from 1" hole in door
insert and tighten screws.
A. Insert latch in hole keeping it
to face of door. Mark outline
and remove latch.
parallel
U
P
UP
TORQUE BLADE SHOULD BE
HORIZONTALLY INSERTED
INTO LATCH CRANK
U
P
UP
TORQUE
BLADE
2-3/8" BACKSET
2-3/4" BACKSET
2
-3/
8" BACKSET
2
-
3/4"
B
A
CKS
E
T
3.INSTALL LATCH
INSTRUCTIONS FOR INSTALLING
DOUBLE CYLINDER DEADLOCKS
FOR INSTALLING
DEADLOCKS
NOTE:
TEMPLATE MUST
BE PLACED ON
HIGH EDGE OF
DOOR BEVEL
MARK
PROPER
DOOR
THICKNESS
DRILL 1"(25mm)
HOLE IN EDGE OF DOOR
(2" IN DEPTH)
READ INSTRUCTIONS
1-3/4"(45mm)THICK
DOOR
1-3/8" 35mm
THICK
DOOR
2-3/4"(70mm)
2-3/8"(60mm)
FOLD HERE
2 /8"BACKSET
3
DRILL
2"(50.8mm)
HOLE
BACKSET
DISTANCE
MARK
UP
JSC-FGS-D101
Customer Service 800-221-3379
Instruction_Lock_19
Customer Service 800-221-3379
Instruction_Lock_19
FOR USE ON DOORS 1-3/8" TO 1-3/4" (35mm-45mm)
INSTRUCTIONS FOR INSTALLATION OF
SINGLE AND DOUBLE CYLINDER DEADLOCKS
(A)
2-3/8" - or - 2-3/4"
(60 mm) (70 mm)
Selecting the Proper Backset
The backset is the distance from the door edge to the center of the hole
UP
Latch Faceplate
Latch Tail
Notch
To adjust the backset from 2-3/8" to 2-3/4" follow these steps.
UP
Retract the latch bolt.
Hold the latch tail and
rotate the faceplate
towards you.
Rotate the latch faceplate
away from you and check
to see if the notch is at
the 2-3/4" mark.
Once the notch is in
the groove, pull the
latch faceplate away
from the latch tail.
UP
UP
U
P
To adjust the backset from 2-3/4" to 2-3/8" follow these steps.
Retract the latch bolt.
Hold the latch tail and
rotate the faceplate
towards you.
Rotate the latch faceplate
away from you and check
to see if the notch is at
the 2-3/8" mark.
Once the notch is in
the groove, push the
latch faceplate towards
the latch tail.
UP
UP
UP
UP