ASSEMBLY INSTRUCTION PATIO DOUBLE LOUNGE WF300797,WF300798
X1 R N- O+ N+ OP- M- P+ S M+ B S T Q D T U E A I F K L G C H J Note: 1. 50% Tighten before fixing all screws, Allen wrench is recommended instead of an electric drill. 2. Place the item on a flat ground to adjust and make sure it remains stable. 3. Tighten up all screw with tools gradually. 4. If screw are not aligned with holes during assembly, please loosen all the other screws to 50% and continue the assembly process. 5.
CARTON CONTENT: WF300797 A x1 B x1 C x1 D x1 H x1 I x1 J x1 S x2 T x2 R x1 Hardware WF300798 E x1 F x1 K x1 G x1 L x1 M+ x1 M- x1 N+ x1 N- x1 O+ x1 O- x1 P+ x1 P- x1 Q x1 U x1 Page: 3/20
Part List: A x1 B x1 Back Right E x1 I x1 Side Left Lounge M+ x1 G x1 Middle Seat Lounge Behind Seat Lounge Side Right Lounge L x1 Front Lounge M- x1 Front Bare N+ x1 N- Support M- Support O+ Support O- x1 Support NP- x1 Support P+ S x2 Covered Middle Bare Support N+ P+ x1 R x1 Support Back H x1 K x1 O- x1 Q x1 Arm Left J x1 Support M+ O+ x1 Arm Right Back Left F x1 Front Seat Lounge D x1 C x1 Back Cushion Support P- T x2 Pilow Cushion U x1 Seat Cushion Page: 4/
Hardware List: 2 x 16 pcs Extra 2 pcs 3 x 20 pcs Extra 2 pcs 4 x 11 pcs Extra 2 pcs BOLT M6 x 20MM BOLT M6 x 30MM BOLT M6 x 35MM BOLT M6 x 55MM 5 x 76 pcs Extra 5 pcs 6 x 10 pcs Extra 2 pcs 7 x 21 pcs Extra 2 pcs 8 x 10 pcs Extra 2 pcs 1 x 4 pcs Extra 2 pcs FLAT WASHER M6 9 x 1 pc WASHER M6 x 5MM 10 x 2 pcs NUT M6 11 x 2 pcs COVER NUT M6 12 x 4 pcs Extra 2 pcs KEY 13 x 1 pc SCREW DIVER ALLEN KEY GASLIFT 14 x 2 pcs 15 x 4 pcs Extra 1 pcs Extra 2 pcs WASHER M6 x 10MM BOLT M6 x 2
STEP 1 B x1 10mm B B Use Allen key to loosen Bolt on the side of Back Left (B) about 10 mm. STEP 2 50% A x1 4 x1 5 x2 7 x1 4 A 5 5 7 X1 Bolt Connect The Part from Step 1 & Back Right (A), tighten Bolt (4), Flat Washer (5), nut (7) with Allen Key (10), Key (9).
STEP 3 50% Q x1 1 x4 5 x4 1 5 1 5 X4 Bolt Q Connect The Part from Step 2 & Support Back (Q), tighten Bolt (1), Flat Washer (5) with Allen Key (10). STEP 4 C x1 10mm C C Use Allen key to loosen Bolt on the side of Arm Right (C) about 10 mm.
STEP 5 4 5 7 50% x1 x2 x1 4 5 5 7 X1 Bolt Connect The Part from Step 3 & Step 4, tighten Bolt (4), Flat Washer (5), Nut (7) with Allen Key (10), Key (9). STEP 6 Dx1 10mm D D Use Allen key to loosen Bolt on the side of Arm Left (D) about 10 mm.
STEP 7 4 5 7 50% x1 x2 x1 4 5 5 7 X1 Bolt Connect The Part from Step 5 & Step 6, tighten Bolt (4), Flat Washer (5), Nut (7) with Allen Key (10), Key (9). STEP 8 K x1 2 x2 5 x2 K 2 5 X2 Bolt Connect The Part from Step 7 & Front Bare (K), tighten Bolt (2), Flat Washer (5) with Allen Key (10).
STEP 9 E x1 E Connect The Part from Step 8 & Front Seat Lounge (E). STEP 10 2 x3 5 x3 50% 5 2 X3 Bolt Connect The Part from Step 9, tighten Bolt (2), Flat Washer (5) with Allen Key (10).
STEP 11 F F x1 3 x2 4 x4 5 x 10 7 x4 3 50% 5 X2 Bolt 4 5 5 X4 Bolt 7 Connect The Part from Step 10 & Middle Seat Lounge (F), tighten Bolt (3),(4) Flat Washer (5), Nut (7) with Allen Key (10), Key (9). STEP 12 3 5 x2 x2 5 X2 Bolt 3 Connect The Part from Step 11, tighten Bolt (3), Flat Washer (5) with Allen Key (10).
STEP 13 50% G x1 4 x4 5 x8 7 x4 G 4 5 5 7 X4 Bolt Connect The Part from Step 12 & Behind Seat Lounge (G), tighten Bolt (4), Flat Washer (5), Nut (7) with Allen Key (10), Key (9). STEP 14 H x1 2 x2 3 x3 5 x5 3 H 5 X3 Bolt 2 5 X2 Bolt Connect The Part from Step 13 & , Side Right Lounge (H), tighten Bolt (2), (3), Flat Washer (5) with Allen Key (10).
STEP 15 50% I x1 2 x2 3 x3 5 x5 5 3 X3 Bolt I 2 5 X2 Bolt Connect The Part from Step 14 & Side Left Lounge (I), tighten Bolt (2), (3), Flat Washer (5) with Allen Key (10). STEP 16 J x1 2 x2 3 x2 5 x4 50% 5 J 3 2 5 Connect The Part from Step 15 & Front Lounge (J), tighten Bolt (2), (3), Flat Washer (5) with Allen Key (10).
STEP 17 50% L x1 2 x5 5 x5 5 2 X5 Bolt L Connect The Part from Step 16 & Middle Bare (L), tighten Bolt (2), Flat Washer (5) with Allen Key (10).
STEP 19 M- M- x 1 N+ x 1 NM+ 12 N- x 1 O+ x 1 100% 13 M+ x 1 ON+ P- O- x 1 X4 Screw P+ x 1 P- x 1 O+ 12 x 4 P+ Connect The Support M+ & Support M- , Support N+ & Support N- , Support O+ & Support O- , Support P+ & Support P-. tighten Screw (12) with Screw Driver (13). STEP 20 R Mx1 R x1 M M 1+ Connect The Support M & Covered (R).
STEP 21 R N x1 2+ N N Connect The Part from Step 20 & Support (N) STEP 22 O x1 R O O 3+ Connect The Part from Step 21 & Support (O) Page: 16/20
STEP 23 P x1 R P P 4+ Connect The Part from Step 22 & Support (P) STEP 24 3 x8 5 x16 6 x8 7 x8 100% 3 7 5 6 5 X8 Bolt Connect The Part from Step 18 & Step 23, tighten Bolt (3), Flat Washer (5), Washer (6), Nut (7) with Allen Key (10), Key (9).
STEP 25 14 5 5 6 x2 7 x2 x6 100% 15 11 11 x 2 14 x 2 X2 Bolt 15 x 4 5 11 15 5 6 7 X2 Bolt Connect The Part from Step 14 & Gaslift (11), tighten Bolt (15), Flat Washer (5), Washer (6),(14) Nut (7) with Allen Key (10), Key (9). STEP 26 8 8 x 10 8 8 8 8 Connect The Part from STEP 25 & Cover Nut (8).
STEP 27 Stick string to Covered to Back Lounge. STEP 28 U x1 U Put on Seat Cushion (U) to Lounge. Stick string to Lounge .
STEP 29 S x2 T x2 S S T T Put on Back Cushion (S) & Pilow Cushion (T) to Lounge.
